钢结构用高强度螺栓、 螺母、垫圈检测

GB/T 1231-2006 钢结构用高强度大六角头螺栓、大六角螺母、垫圈技术条件

本标准规定了钢结构用高强度大六角头螺栓、大六角螺母、垫圈及连接副的技术要求、试验方法、检验规则、标志及包装。 本标准适用于铁路和公路桥梁、锅炉钢结构、工业厂房、高层民用建筑、塔桅结构、起重机械及其他钢结构摩擦型高强度螺栓连接

Specifications of high strength bolts with large hexagon head ，large hexagon nuts，plain washers for steel structures

AS/NZS 1252.1:2016 结构工程用高强度钢紧固件组件 螺栓、螺母和垫圈 第 1 部分：技术要求

​Specifies the dimensional, material and marking requirements for steel bolt assemblies comprising steel bolts of property class 8.8, steel nuts

High-strength steel fastener assemblies for structural engineering — Bolts, nuts and washers, Part 1: Technical requirements

AS/NZS 1252.2:2016 结构工程用高强度钢紧固件组件 螺栓、螺母和垫圈 第 2 部分：螺栓组件的验证测试

Gives provisions for verification testing of high-strength steel fastener assemblies for structural engineering, which is the testing undertaken

High-strength steel fastener assemblies for structural engineering — Bolts, nuts and washers, Part 2: Verification testing for bolt assemblies

IS 6649-1985 高强度结构螺栓和螺母用调质垫圈规范

Covers the requirements for through hardened and tempered steel washers intended for assembly with large series hexagon, high strength structural

T/ZZB 0263-2017 风力发电用高强度螺栓、螺母和垫圈

本标准规定了风力发电用高强度螺栓、螺母和垫圈的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和存储及质量承诺。 本标准适用于公称直径为12 mm～64 mm风力发电用的高强度螺栓、螺母和垫圈（以下简称为螺栓、螺母和垫圈）。 本标准规定的螺栓、螺母和垫圈

High strength bolts, nuts and washer for wind power

KS B 2819-2016 结构连接用扭剪式高强度螺栓、六角螺母、平垫圈组套

Sets of torque-shear type high tension bolt, hexagon nut and plain washer for structural joints

DIN 6918:1990-04 用于槽钢高强度结构螺栓连接的方锥垫圈

Square taper washers for high-strength structual bolting of steel channel sections

GB/T 1230-2006 钢结构用高强度垫圈

本标准规定了规格为12mm～30mm高强度垫圈的形式尺寸、技术条件及标记。 本标准适用于与GB/T 1228《钢结构用高强度大六角头螺纹》配套使用的钢结构摩擦型高强度螺纹连接副

High strength plain washers for steel structures

GOST 22356-1977 高强度螺栓、螺母和垫圈 一般规格

High strength bolts and nuts and washes. General specifications

DIN 6917:1989-10 用于工字钢高强度结构螺栓连接的方锥垫圈

Square taper washers for high-strength structural bolting of steel I sections

GOST R 52643-2006 金属结构用高强度螺钉与螺母垫圈.通用规范

High-strength screws and nuts washers for metal structures. General specifications

JB/ZQ 4080-2006 高强度螺栓专用垫圈

Specialized washers for high strength bolts

GOST R 52646-2006 高强螺栓金属结构用垫圈.规范

Washers for high-strength bolts metal structures. Specifications

KS B ISO 7415-2008(2018 淬火和回火高强度结构螺栓用平垫圈

Plain washers for high-strength structural bolting,hardened and tempered

GOST 32484.5-2013 预加载高强度结构螺栓组件. 平垫圈

High-strength structural bolting assemblies for preloading. Plain washers

GB/T 1231-2006 钢结构用高强度大六角头螺栓、大六角螺母、垫圈技术条件

本标准规定了钢结构用高强度大六角头螺栓、大六角螺母、垫圈及连接副的技术要求、试验方法、检验规则、标志及包装。 本标准适用于铁路和公路桥梁、锅炉钢结构、工业厂房、高层民用建筑、塔桅结构、起重机械及其他钢结构摩擦型高强度螺栓连接

Specifications of high strength bolts with large hexagon head ，large hexagon nuts，plain washers for steel structures

AS/NZS 1252.1:2016 结构工程用高强度钢紧固件组件 螺栓、螺母和垫圈 第 1 部分：技术要求

​Specifies the dimensional, material and marking requirements for steel bolt assemblies comprising steel bolts of property class 8.8, steel nuts

High-strength steel fastener assemblies for structural engineering — Bolts, nuts and washers, Part 1: Technical requirements

AS/NZS 1252.2:2016 结构工程用高强度钢紧固件组件 螺栓、螺母和垫圈 第 2 部分：螺栓组件的验证测试

Gives provisions for verification testing of high-strength steel fastener assemblies for structural engineering, which is the testing undertaken

High-strength steel fastener assemblies for structural engineering — Bolts, nuts and washers, Part 2: Verification testing for bolt assemblies

IS 6649-1985 高强度结构螺栓和螺母用调质垫圈规范

Covers the requirements for through hardened and tempered steel washers intended for assembly with large series hexagon, high strength structural

T/ZZB 0263-2017 风力发电用高强度螺栓、螺母和垫圈

本标准规定了风力发电用高强度螺栓、螺母和垫圈的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和存储及质量承诺。 本标准适用于公称直径为12 mm～64 mm风力发电用的高强度螺栓、螺母和垫圈（以下简称为螺栓、螺母和垫圈）。 本标准规定的螺栓、螺母和垫圈

High strength bolts, nuts and washer for wind power

KS B 2819-2016 结构连接用扭剪式高强度螺栓、六角螺母、平垫圈组套

Sets of torque-shear type high tension bolt, hexagon nut and plain washer for structural joints

DIN 6918:1990-04 用于槽钢高强度结构螺栓连接的方锥垫圈

Square taper washers for high-strength structual bolting of steel channel sections

GB/T 1230-2006 钢结构用高强度垫圈

本标准规定了规格为12mm～30mm高强度垫圈的形式尺寸、技术条件及标记。 本标准适用于与GB/T 1228《钢结构用高强度大六角头螺纹》配套使用的钢结构摩擦型高强度螺纹连接副

High strength plain washers for steel structures

GOST 22356-1977 高强度螺栓、螺母和垫圈 一般规格

High strength bolts and nuts and washes. General specifications

DIN 6917:1989-10 用于工字钢高强度结构螺栓连接的方锥垫圈

Square taper washers for high-strength structural bolting of steel I sections

GOST R 52643-2006 金属结构用高强度螺钉与螺母垫圈.通用规范

High-strength screws and nuts washers for metal structures. General specifications

JB/ZQ 4080-2006 高强度螺栓专用垫圈

Specialized washers for high strength bolts

GOST R 52646-2006 高强螺栓金属结构用垫圈.规范

Washers for high-strength bolts metal structures. Specifications

KS B ISO 7415-2008(2018 淬火和回火高强度结构螺栓用平垫圈

Plain washers for high-strength structural bolting,hardened and tempered

GOST 32484.5-2013 预加载高强度结构螺栓组件. 平垫圈

High-strength structural bolting assemblies for preloading. Plain washers