SAE J914-1965 侧转向信号灯
APPLICATION-This SAE Recommended Practice applies to side turn signal lamps intended for use on trucks and buses over 80 in. in width
Side Turn Signal Lamps
SAE J914-2000 侧转向信号灯
Side Turn Signal Lamps for Vehicles Less Than 12 m in Length
SAE J914-1995 侧转向信号灯
SIDE TURN SIGNAL LAMPS
SAE J914A-1973 侧转向信号灯
This SAE Recommended Practice provides definitions, test requirements, and related procedures for side turn signal lamps
SIDE TURN SIGNAL LAMPS
SAE J914B-1978 侧转向信号灯
This engineering design specification provides parameters and general requirements for side turn signal lamps. It may be supplemented by a service
Side Turn Signal Lamps
SAE J914-1968 侧转向信号灯
SIDE TURN SIGNAL LAMPS
SAE J186-1970 辅助高位停车和转向信号灯
This SAE Recommended Practice provides definitions, performance requirements, and related test procedures for high mounted lamps intended
SUPPLEMENTAL HIGH MOUNTED STOP AND TURN SIGNAL LAMPS
SAE J186-1989 辅助高位停车灯和后转向灯
This document provides design parameters@ performance requirements@ and general installation recommendations for supplemental high mounted stop
Supplemental High Mounted Stop and Rear Turn Signal Lamps
SAE J186A-1977 辅助高位停车灯和后转向灯
This SAE Recommended Practice provides design parameters and general requirements for high mounted amps intended to supplement stop and/or cear turn
Supplemental High Mounted Stop and Rear Turn Signal Lamps
SAE J590E-1975 转向信号灯
Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn
TURN SIGNAL FLASHERS
SAE J590-1986 转向信号灯
This recommended practice defines the test conditions, procedures and minimum design requirements for nominal 6, 12 and 24 volt turn signal flashers
TURN SIGNAL FLASHERS
SAE J590C-1968 转向信号灯
Flashers referred to in this SAE Standard are for nominal 12 or 6 dc circuits and are intended to operate at the design loads for the turn signal
TURN SIGNAL FLASHERS
SAE J590E-1977 转向信号灯
Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn
TURN SIGNAL FLASHERS
SAE J590D-1973 转向信号灯
Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn
TURN SIGNAL FLASHERS
SAE J590-1993 转向信号灯
Turn Signal Flashers
SAE J914-1965 侧转向信号灯
APPLICATION-This SAE Recommended Practice applies to side turn signal lamps intended for use on trucks and buses over 80 in. in width
Side Turn Signal Lamps
SAE J914-2000 侧转向信号灯
Side Turn Signal Lamps for Vehicles Less Than 12 m in Length
SAE J914-1995 侧转向信号灯
SIDE TURN SIGNAL LAMPS
SAE J914A-1973 侧转向信号灯
This SAE Recommended Practice provides definitions, test requirements, and related procedures for side turn signal lamps
SIDE TURN SIGNAL LAMPS
SAE J914B-1978 侧转向信号灯
This engineering design specification provides parameters and general requirements for side turn signal lamps. It may be supplemented by a service
Side Turn Signal Lamps
SAE J914-1968 侧转向信号灯
SIDE TURN SIGNAL LAMPS
SAE J186-1970 辅助高位停车和转向信号灯
This SAE Recommended Practice provides definitions, performance requirements, and related test procedures for high mounted lamps intended
SUPPLEMENTAL HIGH MOUNTED STOP AND TURN SIGNAL LAMPS
SAE J186-1989 辅助高位停车灯和后转向灯
This document provides design parameters@ performance requirements@ and general installation recommendations for supplemental high mounted stop
Supplemental High Mounted Stop and Rear Turn Signal Lamps
SAE J186A-1977 辅助高位停车灯和后转向灯
This SAE Recommended Practice provides design parameters and general requirements for high mounted amps intended to supplement stop and/or cear turn
Supplemental High Mounted Stop and Rear Turn Signal Lamps
SAE J590E-1975 转向信号灯
Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn
TURN SIGNAL FLASHERS
SAE J590-1986 转向信号灯
This recommended practice defines the test conditions, procedures and minimum design requirements for nominal 6, 12 and 24 volt turn signal flashers
TURN SIGNAL FLASHERS
SAE J590C-1968 转向信号灯
Flashers referred to in this SAE Standard are for nominal 12 or 6 dc circuits and are intended to operate at the design loads for the turn signal
TURN SIGNAL FLASHERS
SAE J590E-1977 转向信号灯
Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn
TURN SIGNAL FLASHERS
SAE J590D-1973 转向信号灯
Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn
TURN SIGNAL FLASHERS
SAE J590-1993 转向信号灯
Turn Signal Flashers
编辑：北检院编辑部
