GB/T 10922-2006 55°非密封管螺纹量规
本标准规定了55°非密封管螺纹量规的公差、要求、验收及检验、标志与包装等。 本标准规定的螺纹量规适用于检验GB/T 7307-2001规定的55°非密封管螺纹
Gauges for pipe threads with 55 degree thread angle where pressure-tight joints are not made on the threads
JB/T 10031-2019 55°密封管螺纹量规
55° Sealing Pipe Thread Gauge
JBT10031-2019 55°密封管螺纹量规
55° Sealing Pipe Thread Gauge
JB/T 10031-1999 用螺纹密封的管螺纹量规
本标准规定了用螺纹密封的管螺纹量规的名称,代号,尺寸,公差,检验方法和标志与包装。 本标准适用于检验 GB/T 7306-1987《用螺纹密封的管螺纹》所规定的圆锥螺纹和圆柱内螺纹的尺寸
Gauges for pipe threads where pressure-tight joints are made on the threads
GB/T 22091.1-2008 55°密封管螺纹量规 第1部分:用于检验圆柱内螺纹与圆锥外螺纹
GB/T 22091的本部分规定了55°密封管螺纹量规的设计、尺寸和制造公差、检验、标记等。 本部分规定的量规体系1)适用于检验GB/T 7306.1-2000规定的圆柱内螺纹和圆锥外螺纹
Gauges for pipe threads with 55 degree thread angle where pressure-tight joints are made on the threads. Part 1: Verification of paralled internal and taper external threads
ONORM ISO 228 Teil.2:1984 非螺纹密封的管螺纹.限制量规确认
Diese Internationale Norm legt das Prüfen zylindrischer Gewinde mit Grenzlehren fest. Die Gewindema?e und Toleranzen sind in ISO 228/1 (siehe ?NORM
Pipe threads where pressure-tight joints are not made on the threads; Verification by means of limit gauges
DS/ISO 228/2:1985 非螺纹密封连接的管螺纹. 极限量规检验
Denne standard omhandler verifikation, udf?rt ved hj?lp af gevindtolerancev?rkt?j, af cylindriske gevind med dimensioner og tolerancer, som omtalt i
Pipe threads where pressure-tight joints are not made on the threads. Part 2: Verification by means of limit gauges
BS EN ISO 228-2:2003 非螺纹密封连接的管螺纹.用极限量规检验
This part of IS0 228 specifies the verification, by means of limit gauges, of cylindrical threads, the dimensions and tolerances of which are given
Pipe threads where pressure-tight joints are not made on the threads - Verification by means of limit gauges
CSN ISO 228-2:1993 非螺纹密封的管螺纹.第2部分:限制量规确认
Zpracovatel: ?KODA, koncern, Plzeň, a. s., závod Ná?adí, normalizace, I?O 213 101, Jaromír Straka Technická normaliza?ní komise: TNK 7 Závity
Pipe threads where pressure-tight joints are not made on the threads - Part 2: Vertification by means of limit gauges
KS B ISO 228-2:2007 非螺纹密封的管螺纹.第2部分:极限量规检验
이 규격은 나사 한계 게이지를 이용한 원통형 나사의 검사에 대하여 규정한다. 해당 치수 및
Pipe threads where pressure-tight joints are not made on the threads-Part 2:Verification by means of limit gauges
KS B ISO 228-2:2013 非螺纹密封的管螺纹 第2部分:极限量规检验
Pipe threads where pressure-tight joints are not made on the threads-Part 2:Verification by means of limit gauges
BS EN 10226-3:2005 螺纹上有压力密封接缝的管螺纹.用极限量规验证
This document specifies a process using limit gauges, for the validation of taper internal and external threads and parallel internal threads
Pipe threads where pressure-tight joints are made on the threads - Verification by means of limit gauges
BS EN 10226-3:2005(2016 螺纹上有压力密封接缝的管螺纹.用极限量规验证
Pipe threads where pressure-tight joints are made on the threads - Verification by means of limit gauges
ISO 228-2:1980 非螺纹密封的管螺纹 第2部分:用极限量规检验
Pipe threads where pressure-tight joints are not made on the threads — Part 2: Verification by means of limit gauges
ISO 7-2:2000 用螺纹密封的管螺纹 第2部分:用极限量规检验
This part of ISO 7 specifies a process using limit gauges, for the validation of taper internal and external threads and parallel internal threads
Pipe threads where pressure-tight joints are made on the threads - Part 2: Verification by means of limit gauges
GB/T 10922-2006 55°非密封管螺纹量规
本标准规定了55°非密封管螺纹量规的公差、要求、验收及检验、标志与包装等。 本标准规定的螺纹量规适用于检验GB/T 7307-2001规定的55°非密封管螺纹
Gauges for pipe threads with 55 degree thread angle where pressure-tight joints are not made on the threads
JB/T 10031-2019 55°密封管螺纹量规
55° Sealing Pipe Thread Gauge
JBT10031-2019 55°密封管螺纹量规
55° Sealing Pipe Thread Gauge
JB/T 10031-1999 用螺纹密封的管螺纹量规
本标准规定了用螺纹密封的管螺纹量规的名称,代号,尺寸,公差,检验方法和标志与包装。 本标准适用于检验 GB/T 7306-1987《用螺纹密封的管螺纹》所规定的圆锥螺纹和圆柱内螺纹的尺寸
Gauges for pipe threads where pressure-tight joints are made on the threads
GB/T 22091.1-2008 55°密封管螺纹量规 第1部分:用于检验圆柱内螺纹与圆锥外螺纹
GB/T 22091的本部分规定了55°密封管螺纹量规的设计、尺寸和制造公差、检验、标记等。 本部分规定的量规体系1)适用于检验GB/T 7306.1-2000规定的圆柱内螺纹和圆锥外螺纹
Gauges for pipe threads with 55 degree thread angle where pressure-tight joints are made on the threads. Part 1: Verification of paralled internal and taper external threads
ONORM ISO 228 Teil.2:1984 非螺纹密封的管螺纹.限制量规确认
Diese Internationale Norm legt das Prüfen zylindrischer Gewinde mit Grenzlehren fest. Die Gewindema?e und Toleranzen sind in ISO 228/1 (siehe ?NORM
Pipe threads where pressure-tight joints are not made on the threads; Verification by means of limit gauges
DS/ISO 228/2:1985 非螺纹密封连接的管螺纹. 极限量规检验
Denne standard omhandler verifikation, udf?rt ved hj?lp af gevindtolerancev?rkt?j, af cylindriske gevind med dimensioner og tolerancer, som omtalt i
Pipe threads where pressure-tight joints are not made on the threads. Part 2: Verification by means of limit gauges
BS EN ISO 228-2:2003 非螺纹密封连接的管螺纹.用极限量规检验
This part of IS0 228 specifies the verification, by means of limit gauges, of cylindrical threads, the dimensions and tolerances of which are given
Pipe threads where pressure-tight joints are not made on the threads - Verification by means of limit gauges
CSN ISO 228-2:1993 非螺纹密封的管螺纹.第2部分:限制量规确认
Zpracovatel: ?KODA, koncern, Plzeň, a. s., závod Ná?adí, normalizace, I?O 213 101, Jaromír Straka Technická normaliza?ní komise: TNK 7 Závity
Pipe threads where pressure-tight joints are not made on the threads - Part 2: Vertification by means of limit gauges
KS B ISO 228-2:2007 非螺纹密封的管螺纹.第2部分:极限量规检验
이 규격은 나사 한계 게이지를 이용한 원통형 나사의 검사에 대하여 규정한다. 해당 치수 및
Pipe threads where pressure-tight joints are not made on the threads-Part 2:Verification by means of limit gauges
KS B ISO 228-2:2013 非螺纹密封的管螺纹 第2部分:极限量规检验
Pipe threads where pressure-tight joints are not made on the threads-Part 2:Verification by means of limit gauges
BS EN 10226-3:2005 螺纹上有压力密封接缝的管螺纹.用极限量规验证
This document specifies a process using limit gauges, for the validation of taper internal and external threads and parallel internal threads
Pipe threads where pressure-tight joints are made on the threads - Verification by means of limit gauges
BS EN 10226-3:2005(2016 螺纹上有压力密封接缝的管螺纹.用极限量规验证
Pipe threads where pressure-tight joints are made on the threads - Verification by means of limit gauges
ISO 228-2:1980 非螺纹密封的管螺纹 第2部分:用极限量规检验
Pipe threads where pressure-tight joints are not made on the threads — Part 2: Verification by means of limit gauges
ISO 7-2:2000 用螺纹密封的管螺纹 第2部分:用极限量规检验
This part of ISO 7 specifies a process using limit gauges, for the validation of taper internal and external threads and parallel internal threads
Pipe threads where pressure-tight joints are made on the threads - Part 2: Verification by means of limit gauges
编辑:北检院编辑部















