用螺纹密封的管螺纹量规检测

JB/T 10031-1999 用螺纹密封的管螺纹量规

本标准规定了用螺纹密封的管螺纹量规的名称，代号，尺寸，公差，检验方法和标志与包装。 本标准适用于检验 GB/T 7306-1987《用螺纹密封的管螺纹》所规定的圆锥螺纹和圆柱内螺纹的尺寸

Gauges for pipe threads where pressure-tight joints are made on the threads

ISO 7-2:2000 用螺纹密封的管螺纹 第2部分:用极限量规检验

This part of ISO 7 specifies a process using limit gauges, for the validation of taper internal and external threads and parallel internal threads

Pipe threads where pressure-tight joints are made on the threads - Part 2: Verification by means of limit gauges

NF E03-004-3*NF EN 10226-3:2005 用螺纹密封的管螺纹 第3部分：用极限量规检验

Pipe threads where pressure tight joints are made on the threads - Part 3 : verification by means of limit gauges

DIN EN 10226-3 Berichtigung 1:2006 用螺纹密封的管螺纹.第2部分:用极限量规检验

Pipes threads where pressure tight joint are made on the threads - Part 3: Verification by means of limit gauges; German version EN 10226-3:2005, Corrigenda to DIN EN 10226-3:2005-05

GB/T 10922-2006 55°非密封管螺纹量规

本标准规定了55°非密封管螺纹量规的公差、要求、验收及检验、标志与包装等。 本标准规定的螺纹量规适用于检验GB/T 7307-2001规定的55°非密封管螺纹

Gauges for pipe threads with 55 degree thread angle where pressure-tight joints are not made on the threads

ONORM ISO 228 Teil.2:1984 非螺纹密封的管螺纹．限制量规确认

Diese Internationale Norm legt das Prüfen zylindrischer Gewinde mit Grenzlehren fest. Die Gewindema?e und Toleranzen sind in ISO 228/1 (siehe ?NORM

Pipe threads where pressure-tight joints are not made on the threads; Verification by means of limit gauges

JB/T 10031-2019 55°密封管螺纹量规

55° Sealing Pipe Thread Gauge

JBT10031-2019 55°密封管螺纹量规

55° Sealing Pipe Thread Gauge

BS EN ISO 228-2:2003 非螺纹密封连接的管螺纹.用极限量规检验

This part of IS0 228 specifies the verification, by means of limit gauges, of cylindrical threads, the dimensions and tolerances of which are given

Pipe threads where pressure-tight joints are not made on the threads - Verification by means of limit gauges

NBN 586-1962 用于螺纹和量规间密封接缝的ISO管螺纹

ISO pipe threads for unsealed joints between thread and gauge

ONORM M 1900-1980 螺纹管和螺纹栓用密封圈

Diese ?NORM ist anzuwenden für Dichtringe für Rohrverschraubungen und Verschlu?schrauben. Sie enth?lt Abmessungen und Werkstoffe der Dichtringe der

Sealing rings for screwed pipe ions and screw plugs

AS 1722.1:1975 惠氏管螺纹.密封管螺纹

Pipe threads of Whitworth form Part 1: Sealing pipe threads (metric units)

DS/ISO 228/2:1985 非螺纹密封连接的管螺纹. 极限量规检验

Denne standard omhandler verifikation, udf?rt ved hj?lp af gevindtolerancev?rkt?j, af cylindriske gevind med dimensioner og tolerancer, som omtalt i

Pipe threads where pressure-tight joints are not made on the threads. Part 2: Verification by means of limit gauges

GB/T 12716-2011 60°密封管螺纹

本标准规定了牙型角为60=、螺纹副本身具有密封性的管螺纹(NPT和NPsC〉的牙型、基本尺寸、公差、标记和量规。 本标准适用于管子、阀门、管接头、旋塞及其他管路附件的密封螺纹连接

Pipe threads with the thread angle of 60 degrees where pressure-tight joints are made on threads

ISO 228-2:1980 非螺纹密封的管螺纹 第2部分:用极限量规检验

Pipe threads where pressure-tight joints are not made on the threads — Part 2: Verification by means of limit gauges

JB/T 10031-1999 用螺纹密封的管螺纹量规

本标准规定了用螺纹密封的管螺纹量规的名称，代号，尺寸，公差，检验方法和标志与包装。 本标准适用于检验 GB/T 7306-1987《用螺纹密封的管螺纹》所规定的圆锥螺纹和圆柱内螺纹的尺寸

Gauges for pipe threads where pressure-tight joints are made on the threads

ISO 7-2:2000 用螺纹密封的管螺纹 第2部分:用极限量规检验

This part of ISO 7 specifies a process using limit gauges, for the validation of taper internal and external threads and parallel internal threads

Pipe threads where pressure-tight joints are made on the threads - Part 2: Verification by means of limit gauges

NF E03-004-3*NF EN 10226-3:2005 用螺纹密封的管螺纹 第3部分：用极限量规检验

Pipe threads where pressure tight joints are made on the threads - Part 3 : verification by means of limit gauges

DIN EN 10226-3 Berichtigung 1:2006 用螺纹密封的管螺纹.第2部分:用极限量规检验

Pipes threads where pressure tight joint are made on the threads - Part 3: Verification by means of limit gauges; German version EN 10226-3:2005, Corrigenda to DIN EN 10226-3:2005-05

GB/T 10922-2006 55°非密封管螺纹量规

本标准规定了55°非密封管螺纹量规的公差、要求、验收及检验、标志与包装等。 本标准规定的螺纹量规适用于检验GB/T 7307-2001规定的55°非密封管螺纹

Gauges for pipe threads with 55 degree thread angle where pressure-tight joints are not made on the threads

ONORM ISO 228 Teil.2:1984 非螺纹密封的管螺纹．限制量规确认

Diese Internationale Norm legt das Prüfen zylindrischer Gewinde mit Grenzlehren fest. Die Gewindema?e und Toleranzen sind in ISO 228/1 (siehe ?NORM

Pipe threads where pressure-tight joints are not made on the threads; Verification by means of limit gauges

JB/T 10031-2019 55°密封管螺纹量规

55° Sealing Pipe Thread Gauge

JBT10031-2019 55°密封管螺纹量规

55° Sealing Pipe Thread Gauge

BS EN ISO 228-2:2003 非螺纹密封连接的管螺纹.用极限量规检验

This part of IS0 228 specifies the verification, by means of limit gauges, of cylindrical threads, the dimensions and tolerances of which are given

Pipe threads where pressure-tight joints are not made on the threads - Verification by means of limit gauges

NBN 586-1962 用于螺纹和量规间密封接缝的ISO管螺纹

ISO pipe threads for unsealed joints between thread and gauge

ONORM M 1900-1980 螺纹管和螺纹栓用密封圈

Diese ?NORM ist anzuwenden für Dichtringe für Rohrverschraubungen und Verschlu?schrauben. Sie enth?lt Abmessungen und Werkstoffe der Dichtringe der

Sealing rings for screwed pipe ions and screw plugs

AS 1722.1:1975 惠氏管螺纹.密封管螺纹

Pipe threads of Whitworth form Part 1: Sealing pipe threads (metric units)

DS/ISO 228/2:1985 非螺纹密封连接的管螺纹. 极限量规检验

Denne standard omhandler verifikation, udf?rt ved hj?lp af gevindtolerancev?rkt?j, af cylindriske gevind med dimensioner og tolerancer, som omtalt i

Pipe threads where pressure-tight joints are not made on the threads. Part 2: Verification by means of limit gauges

GB/T 12716-2011 60°密封管螺纹

本标准规定了牙型角为60=、螺纹副本身具有密封性的管螺纹(NPT和NPsC〉的牙型、基本尺寸、公差、标记和量规。 本标准适用于管子、阀门、管接头、旋塞及其他管路附件的密封螺纹连接

Pipe threads with the thread angle of 60 degrees where pressure-tight joints are made on threads

ISO 228-2:1980 非螺纹密封的管螺纹 第2部分:用极限量规检验

Pipe threads where pressure-tight joints are not made on the threads — Part 2: Verification by means of limit gauges