电压检测

📅 发布时间:2024-05-27 👤 来源:北检院 👁 阅读:

AS/NZS 4879.2-2010 特低电压(ELV)灯用变压器和电子式降压变流器的性能.第2部分:最低能效标准(MEPS)要求

Specifies minimum energy performance requirements for ELV convertor, when tested in accordance with AS/NZS 4870.1

Performance of transformers and electronic step-down convertors for ELV lamps - Minimum Energy Performance Standards (MEPS) requirements

GOST R 8.648-2008 确保量测一致性的国家制度.仪器测量在频率范围为1.10(指数为-2)至1.10(指数为9)HZ、1000V的交流电压用国家鉴定计划表

State system for ensuring the uniformity of measurements. State verification schedule for instruments measuring of alternate electrical voltage to 1000 V in the frequency range from 1·10 in minus 2 degree up to 2·10 in 9 degree Hz

NF C52-558-2-6-2009 电压为1100V的变压器、电抗器,电源设备及类似装置的安全性.第2-6部分:安全隔离变压器及带有安全隔离变压器的电源设备用详细要求

Safety of transformers, reactors, power supply units and similar products for voltages up to 1100 V - Part 2-6 : particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers.

DIN EN 50143-2010 空载额定输出电压大于1kV但不超过10kV的信号装置和气体发光管装置用电缆

EN 50143 applies to single core cables of rated voltages up to and including 5/10 kV (U0/U) used with electric signs and high-voltage

Cables for signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 000 V but not exceeding 10 000 V; German version EN 50143:2009

DIN EN 50468-2010 带通信端口的设备用由于闪电导致过电压和过电流的抵抗力要求

This European Standard specifies the minimum level of resistibility of equipment having telecommunicatons port(s) to overvoltages and overcurrents

Resistibility requirements to overvoltages and overcurrents due to lightning for equipment having telecommunication ports; German version EN 50468:2009

NF C71-386-204-2009 数字可寻址照明接口.第204部分:操纵装置详细要求.低电压卤素灯(设备类型3)

Digital addressable lighting interface - Part 204 : particular requirements for control gears - Low voltage halogen lamps (device type 3).

NF C91-004-34/A1-2009 电磁兼容性(EMC).第4-34部分:试验和测量技术.每相电源电流高于16 A的设备用电压骤降,瞬断和电压变化抗扰性试验

Electromagnetic compatibility (EMC) - Part 4-34 : testing and measuring techniques - Voltage dips, short interruptions and voltage variations immunity tests for equipment with mains current more than 16 A per phase.

NF C91-004-14/A2-2009 电磁兼容性(EMC).第4-14部分:测验与评量技术.每相输入电流不超过16 A的设备用电压起伏抗扰性试验

Electromagnetic compatibility (EMC) - Part 4-14 : testing and measurement techniques - Voltage fluctuation immunity test for equipment with input current not exceeding 16 A per phase.

NF C53-701-2009 高电压直流(HVDC)电力传输用电压源换流器(VSC)电子管.电气试验

Voltage sourced converter (VSC) valves for high-voltage direct current (HVDC) power transmission - Electrical testing.

BS EN 61558-2-6-2009 小于1100V供电电压用变压器、电抗器、供电机组及类似设备的安全性.安全隔离变压器及含有安全隔离变压器的供电机组用试验及详细要求

Replacement: This part of IEC 61558 deals with the safety of safety isolating transformers for general applications and power supply units

Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1100 V. Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers

BS EN 62386-205-2009 数字可寻址灯光接口.控制装置的详细要求.白炽灯用电源电压控制器(设备类型4)

This International Standard specifies a protocol and test procedures for the control by digital signals of electronic control gear associated

Digital addressable lighting interface - Particular requirements for control gear - Supply voltage controller for incandescent lamps (device type 4)

BS EN 50397-2-2009 交流额定电压大于1 kV和不超过36 kV的高架电力线和相关配件用包覆导线.包覆导线用配件.试验和验收标准

This Part 2 of EN 50397 contains the requirements for accessories that are for use with the covered conductors in accordance with EN 50397-1

Covered conductors for overhead lines and the related accessories for rated voltages above 1 kV AC and not exceeding 36 kV AC - Accessories for covered conductors - Tests and acceptance criteria

BS EN 62386-206-2009 数字可寻址照明接口.控制装置用详细要求.数字信号转换为直流电压信号(装置类型 5)

This International Standard specifies a protocol and test methods for the control by digital signals of electronic control gear, associated

Digital addressable lighting interface - Particular requirements for control gear - Conversion from digital signal into d.c. voltage (device type 5)

BS EN 60034-15-2009 旋转电机.第15部分:耐用线圈架绕线定子线圈交流旋转电机电平的脉冲电压

This part of IEC 60034 relates to a.c. machines incorporating form-wound stator coils. It specifies the test procedures and voltages to be applied

Rotating electrical machines - Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines

BS EN 61000-4-14-1999+A2-2009 电磁兼容性(EMC).试验和测量技术.每相输入电流不超过16A的设备用电压波动防护试验

This part of IEC 61000 is a basic electromagnetic compatibility (EMC) publication. It considers immunity tests for electrical and/or electronic

Electromagnetic compatibility (EMC) - Testing and measurement techniques - Voltage fluctuation immunity test for equipment with input current not exceeding 16 A per phase

AS/NZS 4879.2-2010 特低电压(ELV)灯用变压器和电子式降压变流器的性能.第2部分:最低能效标准(MEPS)要求

Specifies minimum energy performance requirements for ELV convertor, when tested in accordance with AS/NZS 4870.1

Performance of transformers and electronic step-down convertors for ELV lamps - Minimum Energy Performance Standards (MEPS) requirements

GOST R 8.648-2008 确保量测一致性的国家制度.仪器测量在频率范围为1.10(指数为-2)至1.10(指数为9)HZ、1000V的交流电压用国家鉴定计划表

State system for ensuring the uniformity of measurements. State verification schedule for instruments measuring of alternate electrical voltage to 1000 V in the frequency range from 1·10 in minus 2 degree up to 2·10 in 9 degree Hz

NF C52-558-2-6-2009 电压为1100V的变压器、电抗器,电源设备及类似装置的安全性.第2-6部分:安全隔离变压器及带有安全隔离变压器的电源设备用详细要求

Safety of transformers, reactors, power supply units and similar products for voltages up to 1100 V - Part 2-6 : particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers.

DIN EN 50143-2010 空载额定输出电压大于1kV但不超过10kV的信号装置和气体发光管装置用电缆

EN 50143 applies to single core cables of rated voltages up to and including 5/10 kV (U0/U) used with electric signs and high-voltage

Cables for signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 000 V but not exceeding 10 000 V; German version EN 50143:2009

DIN EN 50468-2010 带通信端口的设备用由于闪电导致过电压和过电流的抵抗力要求

This European Standard specifies the minimum level of resistibility of equipment having telecommunicatons port(s) to overvoltages and overcurrents

Resistibility requirements to overvoltages and overcurrents due to lightning for equipment having telecommunication ports; German version EN 50468:2009

NF C71-386-204-2009 数字可寻址照明接口.第204部分:操纵装置详细要求.低电压卤素灯(设备类型3)

Digital addressable lighting interface - Part 204 : particular requirements for control gears - Low voltage halogen lamps (device type 3).

NF C91-004-34/A1-2009 电磁兼容性(EMC).第4-34部分:试验和测量技术.每相电源电流高于16 A的设备用电压骤降,瞬断和电压变化抗扰性试验

Electromagnetic compatibility (EMC) - Part 4-34 : testing and measuring techniques - Voltage dips, short interruptions and voltage variations immunity tests for equipment with mains current more than 16 A per phase.

NF C91-004-14/A2-2009 电磁兼容性(EMC).第4-14部分:测验与评量技术.每相输入电流不超过16 A的设备用电压起伏抗扰性试验

Electromagnetic compatibility (EMC) - Part 4-14 : testing and measurement techniques - Voltage fluctuation immunity test for equipment with input current not exceeding 16 A per phase.

NF C53-701-2009 高电压直流(HVDC)电力传输用电压源换流器(VSC)电子管.电气试验

Voltage sourced converter (VSC) valves for high-voltage direct current (HVDC) power transmission - Electrical testing.

BS EN 61558-2-6-2009 小于1100V供电电压用变压器、电抗器、供电机组及类似设备的安全性.安全隔离变压器及含有安全隔离变压器的供电机组用试验及详细要求

Replacement: This part of IEC 61558 deals with the safety of safety isolating transformers for general applications and power supply units

Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1100 V. Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers

BS EN 62386-205-2009 数字可寻址灯光接口.控制装置的详细要求.白炽灯用电源电压控制器(设备类型4)

This International Standard specifies a protocol and test procedures for the control by digital signals of electronic control gear associated

Digital addressable lighting interface - Particular requirements for control gear - Supply voltage controller for incandescent lamps (device type 4)

BS EN 50397-2-2009 交流额定电压大于1 kV和不超过36 kV的高架电力线和相关配件用包覆导线.包覆导线用配件.试验和验收标准

This Part 2 of EN 50397 contains the requirements for accessories that are for use with the covered conductors in accordance with EN 50397-1

Covered conductors for overhead lines and the related accessories for rated voltages above 1 kV AC and not exceeding 36 kV AC - Accessories for covered conductors - Tests and acceptance criteria

BS EN 62386-206-2009 数字可寻址照明接口.控制装置用详细要求.数字信号转换为直流电压信号(装置类型 5)

This International Standard specifies a protocol and test methods for the control by digital signals of electronic control gear, associated

Digital addressable lighting interface - Particular requirements for control gear - Conversion from digital signal into d.c. voltage (device type 5)

BS EN 60034-15-2009 旋转电机.第15部分:耐用线圈架绕线定子线圈交流旋转电机电平的脉冲电压

This part of IEC 60034 relates to a.c. machines incorporating form-wound stator coils. It specifies the test procedures and voltages to be applied

Rotating electrical machines - Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines

BS EN 61000-4-14-1999+A2-2009 电磁兼容性(EMC).试验和测量技术.每相输入电流不超过16A的设备用电压波动防护试验

This part of IEC 61000 is a basic electromagnetic compatibility (EMC) publication. It considers immunity tests for electrical and/or electronic

Electromagnetic compatibility (EMC) - Testing and measurement techniques - Voltage fluctuation immunity test for equipment with input current not exceeding 16 A per phase

编辑:北检院编辑部

我们的优势

选择北检院的六大理由

📚

CMA/CNAS 双认证

旗下实验室具备国家认证认可监督管理委员会CMA资质认定及中国合格评定国家认可委员会CNAS实验室认可,检测报告具有国际公信力。

🔬

1000+ 台套先进设备

配备扫描电镜、气质联用仪、电感耦合等离子体质谱仪等国际先进检测仪器,确保数据精准可靠。

🏢

15000+ 平米实验室

拥有规模化专业检测基地,涵盖材料、化工、食品、环境等多个专业实验室,满足多领域检测需求。

👥

资深技术团队

汇聚材料科学、化学分析、环境工程等领域专家,拥有10年+行业经验,提供专业可靠的检测分析服务。

快速响应机制

标准检测周期短至3个工作日,加急服务24小时出具报告,全程一对一工程师跟进,确保高效交付。

🌎

全国服务网络

总部位于北京,山东设立分部,服务覆盖全国,为20万+客户提供便捷的一站式检测解决方案。

荣誉资质

旗下实验室资质荣誉

CMA 检验检测机构资质认定

CMA 检验检测机构资质认定

国家认证认可监督管理委员会颁发,具备向社会出具具有证明作用数据的资质。

CNAS 实验室认可证书

CNAS 实验室认可证书

中国合格评定国家认可委员会认可,检测结果获国际互认,具有国际公信力。

ISO 质量管理体系认证

ISO 质量管理体系认证

通过ISO 质量管理体系认证,管理体系实现规范化、标准化。

绿色低碳诚信示范创建企业

绿色低碳诚信示范创建企业

荣获绿色低碳诚信示范创建企业称号,践行可持续发展理念,推动绿色低碳转型,助力"双碳"目标实现。

北京市创新型中小企业

北京市"创新型"中小企业

经北京市经济和信息化局认定的创新型中小企业,具备较强创新能力与较高专业化水平,是优质中小企业梯度培育体系的重要基础力量。

北京市专精特新中小企业

北京市"专精特新"中小企业

经北京市经济和信息化局认定的专精特新中小企业,具备专业化、精细化、特色化、新颖化发展特征,在细分领域具有较强竞争优势。

查看全部资质

仪器设备

国际先进检测仪器,确保检测数据精准可靠

查看全部设备

检测流程

标准化流程,高效交付

01

需求沟通

客户提交检测需求,技术顾问一对一沟通,明确检测项目与标准。

02

样品寄送

客户按照规范要求寄送样品,实验室确认样品状态与数量。

03

实验检测

专业工程师按照标准方法进行检测分析,全程质量控制。

04

数据审核

检测数据经多级审核,确保结果准确、可靠、可追溯。

05

报告出具

出具检测报告,支持电子版与纸质版,快递送达。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通