发布时间:2023-04-18 03:07:31
点击量:0
Specifies methods for the manual ultrasonic testing of fusion welded joints in metallic materials. Intended for use on full penetration welded joints
Non-destructive testing of welds - Ultrasonic testing of welded joints
Ultrasonic testing. Ultrasound probe
Establishes the procedures for measuring performance characteristics of components of pulse-echo ultrasonic non-destructive testing instruments
Non-destructive testing - Ultrasonic inspection - Evaluating electronic characteristics of ultrasonic test instruments
Non-destructive Testing. Welded Joints. Ultrasonic Methods
1.1本标准确立了带屏幕显示的模拟和数字式脉冲回波超声损检测仪各部件性能特性的检测方法。 其目的是建立一种统一的评定方法,为不同实验室和不同时间获取的检测数据的比较及测量结果的分析处理提供依据。 本标准未规定验收准则,该验收准则宜由使用方规定。 超声检测仪的通用部件及其性能特性,包括测量这些
Non-destructive testing.Ultrasonic inspection.Evaluating electronic characteristics of ultrasonic test instruments
Prezentul standard stabile?te condi?ii tehnice generale pentru efectuarea examin?rii manuale cu ui r?sunete a ?mbin?rilor sudate prin topire
Ultrasonic fault detection MANUAL EXAMINATION OF FUSE WELDING JOINTS
Non.destructive testing for welded joints.Ultrasonic methods
本标准规定了利用手工扫查或自动(半自动)扫查的一维线阵相控阵超声技术应用基本原则,进行检测时工艺参数的选用规则,以及确定缺陷位置及尺寸的方法。 本标准适用于厚度为6 mm~200 mm的细晶钢焊接接头。对于其他金属细晶材料焊接接头,在考虑声速的变化后,也可参照本标准。对于厚度超出以上范围的焊接接头
Non-destructive testing.Ultrasonic testing.Test method for phased-array ultrasonic testing
ULTRASONIC INSPECTION OF WELDMENTS
This standard establishes the minimum conditions demanded to undertake nondestructive testing through ultrasonic examination on a welded joint, using
NDT - Ultrasound in welding - Procedure
Ultrasonic testing
本标准规定了P91钢制承压设备对接焊接接头超声波检测一般要求、检测方法、缺陷判定与评级。 本标准适用于采用A型脉冲反射式超声波探伤仪检测P91钢制承压设备对接焊接接头缺陷。 本标准不适用于外径小于等于159承压设备管子和管道环向对接焊接接头超声检测
1.1 This practice covers techniques for the ultrasonic A-scan examination of specific weld configurations joining wrought ferrous or aluminum alloy
Standard Practice for Ultrasonic Contact Examination of Weldments
Specifies methods for the manual ultrasonic testing of fusion welded joints in metallic materials. Intended for use on full penetration welded joints
Non-destructive testing of welds - Ultrasonic testing of welded joints
Ultrasonic testing. Ultrasound probe
Establishes the procedures for measuring performance characteristics of components of pulse-echo ultrasonic non-destructive testing instruments
Non-destructive testing - Ultrasonic inspection - Evaluating electronic characteristics of ultrasonic test instruments
Non-destructive Testing. Welded Joints. Ultrasonic Methods
1.1本标准确立了带屏幕显示的模拟和数字式脉冲回波超声损检测仪各部件性能特性的检测方法。 其目的是建立一种统一的评定方法,为不同实验室和不同时间获取的检测数据的比较及测量结果的分析处理提供依据。 本标准未规定验收准则,该验收准则宜由使用方规定。 超声检测仪的通用部件及其性能特性,包括测量这些
Non-destructive testing.Ultrasonic inspection.Evaluating electronic characteristics of ultrasonic test instruments
Prezentul standard stabile?te condi?ii tehnice generale pentru efectuarea examin?rii manuale cu ui r?sunete a ?mbin?rilor sudate prin topire
Ultrasonic fault detection MANUAL EXAMINATION OF FUSE WELDING JOINTS
Non.destructive testing for welded joints.Ultrasonic methods
本标准规定了利用手工扫查或自动(半自动)扫查的一维线阵相控阵超声技术应用基本原则,进行检测时工艺参数的选用规则,以及确定缺陷位置及尺寸的方法。 本标准适用于厚度为6 mm~200 mm的细晶钢焊接接头。对于其他金属细晶材料焊接接头,在考虑声速的变化后,也可参照本标准。对于厚度超出以上范围的焊接接头
Non-destructive testing.Ultrasonic testing.Test method for phased-array ultrasonic testing
ULTRASONIC INSPECTION OF WELDMENTS
This standard establishes the minimum conditions demanded to undertake nondestructive testing through ultrasonic examination on a welded joint, using
NDT - Ultrasound in welding - Procedure
Ultrasonic testing
本标准规定了P91钢制承压设备对接焊接接头超声波检测一般要求、检测方法、缺陷判定与评级。 本标准适用于采用A型脉冲反射式超声波探伤仪检测P91钢制承压设备对接焊接接头缺陷。 本标准不适用于外径小于等于159承压设备管子和管道环向对接焊接接头超声检测
1.1 This practice covers techniques for the ultrasonic A-scan examination of specific weld configurations joining wrought ferrous or aluminum alloy
Standard Practice for Ultrasonic Contact Examination of Weldments