ISO 15822:2007 对角变形时门具开启性能试验方法.地震方面
This International Standard specifies the test method for evaluating the opening function of single-leaf doorset under in-plane diagonal deformation
Test method of doorset opening performance in diagonal deformation - Seismic aspects
GB/T 34553-2017 门在地震作用下角变形时的开启性能试验方法
Test method of doorset opening performance in diagonal deformation under seismic aspects
ANSI/ASTM F2379:2004 电动开启清洗槽能量性能的试验方法
This test method evaluates the energy consumption of powered open warewashing sinks. The food service operator can use these tests to evaluate
Test Method for Energy Performance of Powered Open Warewashing Sinks
GM GM2802M-1995 开关组件空档启动支持.顺时针
Switch Assembly Neutral Start Backup - Clockwise
GM GM2805M-1995 开关组件空档启动支持.逆时针
Switch Assembly Neutral Start Backup - Counterclockwise
SAE AIR 4077-1989 启动起落架时机械开关的用法
This Aerospace Information Report (AIR) will examine considerations relative to the use of mechanical switches on aircraft landing gear, and present
Mechanical Switch Usage for Landing Gear Applications
ASTM F2379-04(2010 电动开启清洗槽能量性能的标准试验方法
The energy input rate test is used to confirm that the powered sink is operating properly prior to further testing.
Preheat energy and time
Standard Test Method for Energy Performance of Powered Open Warewashing Sinks
ASTM D6325-98(2011 毛毡胶粘剂开启使用时间测定的试验方法
The ability to have a sufficient open assembly time is critical when bonding a carpet. An adhesive with too short an open assembly time
Test Method for Determining Open Assembly Time of Carpet Mastic Adhesives
GB/T 41504-2022 建筑外门窗及百叶防非正常开启性能检测方法
Test method of burglar resistance for building external windows, doors and shutters
PNS ISO 15822:2021 斜向变形中门套开启性能的试验方法.地震方面
Test method of doorset opening performance in diagonal deformation - Seismic aspects
T/DZJN 41-2021 商用开水器能效限定值及能效等级
4.3 能效限定值 在文件规定的试验条件下，开水器所规定的最低热效率和保温温度下降值。 5 试验方法 5.1 一般试验条件 本文件试验均在下列条件下进行。 a)单相电源电压为220V±5%，三相电源电压为
DS/EN 60927+A1-1994 启动装置（日光灯启动器除外）．性能要求
Starting devices (other than glow starters) - Performance requirements
SNI 09-4051-1996 机车启动开关
Starter switches for motor vehicles
MSZ 05 29.0820-1971 螺钉开启设备
KS B 3506-2002 钻孔开启尺寸
이 규격은 브로치 물림부(이하 물림부라 한다.)의 모양 및 치수에 대하여 규정한다
Dimensions of pull and follower ends of broach
ISO 15822:2007 对角变形时门具开启性能试验方法.地震方面
This International Standard specifies the test method for evaluating the opening function of single-leaf doorset under in-plane diagonal deformation
Test method of doorset opening performance in diagonal deformation - Seismic aspects
GB/T 34553-2017 门在地震作用下角变形时的开启性能试验方法
Test method of doorset opening performance in diagonal deformation under seismic aspects
ANSI/ASTM F2379:2004 电动开启清洗槽能量性能的试验方法
This test method evaluates the energy consumption of powered open warewashing sinks. The food service operator can use these tests to evaluate
Test Method for Energy Performance of Powered Open Warewashing Sinks
GM GM2802M-1995 开关组件空档启动支持.顺时针
Switch Assembly Neutral Start Backup - Clockwise
GM GM2805M-1995 开关组件空档启动支持.逆时针
Switch Assembly Neutral Start Backup - Counterclockwise
SAE AIR 4077-1989 启动起落架时机械开关的用法
This Aerospace Information Report (AIR) will examine considerations relative to the use of mechanical switches on aircraft landing gear, and present
Mechanical Switch Usage for Landing Gear Applications
ASTM F2379-04(2010 电动开启清洗槽能量性能的标准试验方法
The energy input rate test is used to confirm that the powered sink is operating properly prior to further testing.
Preheat energy and time
Standard Test Method for Energy Performance of Powered Open Warewashing Sinks
ASTM D6325-98(2011 毛毡胶粘剂开启使用时间测定的试验方法
The ability to have a sufficient open assembly time is critical when bonding a carpet. An adhesive with too short an open assembly time
Test Method for Determining Open Assembly Time of Carpet Mastic Adhesives
GB/T 41504-2022 建筑外门窗及百叶防非正常开启性能检测方法
Test method of burglar resistance for building external windows, doors and shutters
PNS ISO 15822:2021 斜向变形中门套开启性能的试验方法.地震方面
Test method of doorset opening performance in diagonal deformation - Seismic aspects
T/DZJN 41-2021 商用开水器能效限定值及能效等级
4.3 能效限定值 在文件规定的试验条件下，开水器所规定的最低热效率和保温温度下降值。 5 试验方法 5.1 一般试验条件 本文件试验均在下列条件下进行。 a)单相电源电压为220V±5%，三相电源电压为
DS/EN 60927+A1-1994 启动装置（日光灯启动器除外）．性能要求
Starting devices (other than glow starters) - Performance requirements
SNI 09-4051-1996 机车启动开关
Starter switches for motor vehicles
MSZ 05 29.0820-1971 螺钉开启设备
KS B 3506-2002 钻孔开启尺寸
이 규격은 브로치 물림부(이하 물림부라 한다.)의 모양 및 치수에 대하여 규정한다
Dimensions of pull and follower ends of broach
编辑：北检院编辑部
