热收缩式终端检测

JB/T 7829-1995 额定电压26/35kV及以下电力电缆.户内型、户外型热收缩式终端

本标准规定了额定电压26/35 kV及以下电力电缆用户内型、户外型热收缩式终端的产品标记和代号、技术要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于额定电压U|(o)/U为26/35kV及以下挤包塑料绝缘电力电缆和8.7/10kV及以下不滴流纸绝缘电力电缆用户内型

JB/T 7829-2006 额定电压1kV（Um=1.2 kV）到35kV（Um=40.5 kV）电力电缆热收缩式终端

本标准规定了额定电压1kV（Um=1.2kV）到35kV（Um=40.5kV）电力电缆用热收缩式终端的产品标记、代号、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于额定电压1kV（Um=1.2kV）至35kV（Um=40.5kV）挤包绝缘电力电缆和额定电压1kV（Um

Thermal shrinkage terminals for power supply cables with rated voltage between 1kV ( Um= 1.2 kV) and 35kV (Um= 40.5 kV).

SAE AS83519B-2011 耐环境热收缩绝缘焊接式屏蔽终端的一般规格

This specification covers environment resistant, heat-shrinkable solder type shield terminations. They may be used on data-bus, RF and shielded cables

Shield Termination, Solder Style, Insulated, Heat-Shrinkable, Environment Resistant General Specification for

SAE AS83519/1-1998 带锡或银镀层电缆用耐环境、焊接式、绝缘和热收缩性的屏蔽终端(I类)

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT FOR CABLES HAVING TIN OR SILVER PLATED SHIELDS (CLASS I) FSC 5940

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT FOR CABLES HAVING TIN OR SILVER PLATED SHIELDS (CLASS I) FSC 5940; Should Be Used for New Design Instead of MIL-S-83519/1, which Was Inactivated for New Design on August

SAE AS83519/2-1998 带锡或银镀层电缆用预安装线的耐环境、焊接式、绝缘和热收缩性的屏蔽终端(I类)

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT WITH PRE INSTALLED LEADS FOR CABLES HAVING TIN OR SILVER PLATED

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT WITH PRE INSTALLED LEADS FOR CABLES HAVING TIN OR SILVER PLATED SHIELDS (CLASS I) FSC 5940; Should Be Used Instead of MIL-S-83519/2 Which Was Inactivated for New Design o

NAVY QPL-AS83519-2-2006 耐环境热缩性焊接式屏蔽终端

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject non-Government standard

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT, GENERAL SPECIFICATION FOR

NAVY QPL-AS83519-QPD-2010 耐环境型热收缩绝缘焊接型屏蔽终端一般规范

Shield Termination, Solder Style, Insulated, Heat-Shrinkable, Environment Resistant, General Specification for

AIA/NAS NAS 1745-1994 (Rev. 7)防潮绝缘可收缩热空气焊接型防护终端接合

NAS1637, "Handle, Latching Internal and External Release Components and Assembly", was adopted2 1 -oAnU G-95 for use by the Department of Defense

Splice, Shield Termination Solder Style, Hot Air Shrinkable, Insulated, Moisture Resistant (Rev. 7)

AIA/NAS NAS 1746-1994 (Rev. 6)防潮绝缘可收缩热空气焊接型防护终端接合

THIS STANOARD DEFINES THE REQUIREMENTS FOR SPLICES WHICH REDUCE TO A PREOETERMINED DIAMETER UPON THE CONTROLLED APPLICATION OF HEAT, THESE SPLICES

Splice, Shield Termination, Solder Style Infrared Shrinkable, Insulated, Moisture Resistant (Rev. 6)

AIA/NAS NAS 1747-1990 (Rev. 4)规格绝缘热收缩焊接型导体及防护终端接合

This specification covers the general requirements for manually operated control knobs and associated knob locks for use with electronic

Splice, Conductor and Shield Termination, Solder Style, Heat Shrinkable, Insulated, Specification for (Rev. 4)

SAE AS83519/5-2014 ROHS, I类镀镍预装编织耐环境型热收缩绝缘焊接型护套终端

Scope is unavailable

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT WITH PREINSTALLED BRAID, NI PLATED, CLASS I, ROHS

SAE AS83519/3-2014 非ROHS, I类镀锡预装编织耐环境型热收缩绝缘焊接型护套终端

Scope is unavailable

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT WITH PREINSTALLED BRAID,TIN PLATED, CLASS I, NON-ROHS

T/ZZB 2307-2021 智慧自助收银终端

本文件规定了智慧自助收银终端（简称“终端”）的术语和定义、结构型式、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存、安装和质量承诺等。 本文件适用于超市、商场等室内场所实现自助结账、打印购物小票等功能的智能终端类产品。不适用于带现金模块的收银终端

Specification of the smart self-service cashier

SAE AS83519A-A3-2008 航空航天标准修改件.耐环境焊接型绝缘热收缩铠装终端用一般规范

THIS AMENDMENT FORMS A PART OF AS83519A, DATED 2003-07

AEROSPACE STANDARD AMENDMENT Shield Termination, Solder Style, Insulated, Heat-Shrinkable, Environment Resistant General Specification For

JB/T 11330-2013 热收缩雨裙

本标准规定了热收缩雨裙的型号与命名、技术要求、试验方法、检验规则及标志、包装、运输和贮存。本标准适用于聚烯烃热收缩雨裙

Heat-shrinkable shed

JB/T 7829-1995 额定电压26/35kV及以下电力电缆.户内型、户外型热收缩式终端

本标准规定了额定电压26/35 kV及以下电力电缆用户内型、户外型热收缩式终端的产品标记和代号、技术要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于额定电压U|(o)/U为26/35kV及以下挤包塑料绝缘电力电缆和8.7/10kV及以下不滴流纸绝缘电力电缆用户内型

JB/T 7829-2006 额定电压1kV（Um=1.2 kV）到35kV（Um=40.5 kV）电力电缆热收缩式终端

本标准规定了额定电压1kV（Um=1.2kV）到35kV（Um=40.5kV）电力电缆用热收缩式终端的产品标记、代号、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于额定电压1kV（Um=1.2kV）至35kV（Um=40.5kV）挤包绝缘电力电缆和额定电压1kV（Um

Thermal shrinkage terminals for power supply cables with rated voltage between 1kV ( Um= 1.2 kV) and 35kV (Um= 40.5 kV).

SAE AS83519B-2011 耐环境热收缩绝缘焊接式屏蔽终端的一般规格

This specification covers environment resistant, heat-shrinkable solder type shield terminations. They may be used on data-bus, RF and shielded cables

Shield Termination, Solder Style, Insulated, Heat-Shrinkable, Environment Resistant General Specification for

SAE AS83519/1-1998 带锡或银镀层电缆用耐环境、焊接式、绝缘和热收缩性的屏蔽终端(I类)

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT FOR CABLES HAVING TIN OR SILVER PLATED SHIELDS (CLASS I) FSC 5940

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT FOR CABLES HAVING TIN OR SILVER PLATED SHIELDS (CLASS I) FSC 5940; Should Be Used for New Design Instead of MIL-S-83519/1, which Was Inactivated for New Design on August

SAE AS83519/2-1998 带锡或银镀层电缆用预安装线的耐环境、焊接式、绝缘和热收缩性的屏蔽终端(I类)

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT WITH PRE INSTALLED LEADS FOR CABLES HAVING TIN OR SILVER PLATED

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT WITH PRE INSTALLED LEADS FOR CABLES HAVING TIN OR SILVER PLATED SHIELDS (CLASS I) FSC 5940; Should Be Used Instead of MIL-S-83519/2 Which Was Inactivated for New Design o

NAVY QPL-AS83519-2-2006 耐环境热缩性焊接式屏蔽终端

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject non-Government standard

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT, GENERAL SPECIFICATION FOR

NAVY QPL-AS83519-QPD-2010 耐环境型热收缩绝缘焊接型屏蔽终端一般规范

Shield Termination, Solder Style, Insulated, Heat-Shrinkable, Environment Resistant, General Specification for

AIA/NAS NAS 1745-1994 (Rev. 7)防潮绝缘可收缩热空气焊接型防护终端接合

NAS1637, "Handle, Latching Internal and External Release Components and Assembly", was adopted2 1 -oAnU G-95 for use by the Department of Defense

Splice, Shield Termination Solder Style, Hot Air Shrinkable, Insulated, Moisture Resistant (Rev. 7)

AIA/NAS NAS 1746-1994 (Rev. 6)防潮绝缘可收缩热空气焊接型防护终端接合

THIS STANOARD DEFINES THE REQUIREMENTS FOR SPLICES WHICH REDUCE TO A PREOETERMINED DIAMETER UPON THE CONTROLLED APPLICATION OF HEAT, THESE SPLICES

Splice, Shield Termination, Solder Style Infrared Shrinkable, Insulated, Moisture Resistant (Rev. 6)

AIA/NAS NAS 1747-1990 (Rev. 4)规格绝缘热收缩焊接型导体及防护终端接合

This specification covers the general requirements for manually operated control knobs and associated knob locks for use with electronic

Splice, Conductor and Shield Termination, Solder Style, Heat Shrinkable, Insulated, Specification for (Rev. 4)

SAE AS83519/5-2014 ROHS, I类镀镍预装编织耐环境型热收缩绝缘焊接型护套终端

Scope is unavailable

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT WITH PREINSTALLED BRAID, NI PLATED, CLASS I, ROHS

SAE AS83519/3-2014 非ROHS, I类镀锡预装编织耐环境型热收缩绝缘焊接型护套终端

Scope is unavailable

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT WITH PREINSTALLED BRAID,TIN PLATED, CLASS I, NON-ROHS

T/ZZB 2307-2021 智慧自助收银终端

本文件规定了智慧自助收银终端（简称“终端”）的术语和定义、结构型式、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存、安装和质量承诺等。 本文件适用于超市、商场等室内场所实现自助结账、打印购物小票等功能的智能终端类产品。不适用于带现金模块的收银终端

Specification of the smart self-service cashier

SAE AS83519A-A3-2008 航空航天标准修改件.耐环境焊接型绝缘热收缩铠装终端用一般规范

THIS AMENDMENT FORMS A PART OF AS83519A, DATED 2003-07

AEROSPACE STANDARD AMENDMENT Shield Termination, Solder Style, Insulated, Heat-Shrinkable, Environment Resistant General Specification For

JB/T 11330-2013 热收缩雨裙

本标准规定了热收缩雨裙的型号与命名、技术要求、试验方法、检验规则及标志、包装、运输和贮存。本标准适用于聚烯烃热收缩雨裙

Heat-shrinkable shed