电压/电流传感器检测

📅 发布时间:2024-05-27 👤 来源:北检院 👁 阅读:

ANSI/IEEE C37.92:2005 保护电压和电流传感器中继电器的模拟输入标准

Defines the interface between voltage or current tranducer systems or sensing systems with analog electronic outputs, and suitably designed protective

Standard for Analog Inputs to Protective Relays from Electronic Voltage and Current Transducers

SJ 20790-2000 电流电压传感器总规范

本规范规定了军用电流电压传感器和电压传感器的通用要求、质量保证规定和试验方法等。 本规范主要适用于其传感器输出与被测电流与电压成线性关系的传感器。其它传感器也可参照采用

General specification for current and voltage sensors

GJB 8354-2015 电流电压传感器通用规范

TB/T 2763-2009 机车车辆用电流传感器和电压传感器

本标准规定了铁道机车车辆用电流传感器和电压传感器的技术要求、试验方法、检验规则及产品标志、包装、运输和储存等。 本标准适用于铁道机车车辆上对直流、交流、脉流的电流或电压进行测量的电流传感器和电压传感器。 本标准也可适用于地铁、轻轨等其他轨道交通车辆上的电流传感器和电压传感器

On-board current transducer and voltage transducer for rolling stock

GOST R 56750-2015 交流电测量设备. 特殊要求. 连接电压和电流低功率传感器 (电子式互感器) 的模拟输入仪表

Electricity metering equipment (a.c.). Particular requirements. Meters with analog inputs connected to the low-power sensor (electronic transformers) of voltage and current

BS EN 62689-1:2016 故障通道指示用电流和电压传感器或检测器. 通用原则和要求

Current and voltage sensors or detectors, to be used for fault passage indication purposes. General principles and requirements

GOST R 8.669-2009 国家测量统一性保证体系.压电感应及涡电流震动传感器振动仪.鉴定方法及手段

State system for ensuring the uniformity of measurements. Vibrometers with piezoelectric, induction and eddy current vibrations transducers. Methods of verification

GB/T 41135.1-2021 故障路径指示用电流和电压传感器或探测器 第1部分:通用原理和要求

Current and voltage sensors or detectors, to be used for fault passage indication purposes—Part 1: General principles and requirements

GB/T 41135.2-2021 故障路径指示用电流和电压传感器或探测器 第2部分:系统应用

Current and voltage sensors or detectors, to be used for fault passage indication purposes—Part 2: System aspects

IEC 62689-2:2016 电流和电压传感器或检测器 用于故障通道指示用途第2部分:系统方面

This part of IEC 62689 describes electric phenomena and electric system behaviour during faults@ according to the most widely diffused distribution

Current and voltage sensors or detectors, to be used for fault passage indication purposes - Part 2: System aspects

IEC 62689-1:2016 电流和电压传感器或检测器 用于故障通道指示用途第1部分:一般原则和要求

This part of IEC 62689 defines the minimum requirements (therefore performances) and consequent classification and tests (with the exception

Current and voltage sensors or detectors, to be used for fault passage indication purposes - Part 1: General principles and requirements

BS PD IEC/TR 62689-100:2016 故障通道指示用电流和电压传感器或检测器. 支持断层通道指示应用的IEC 61850系列数据模型扩展要求和建议

Current and voltage sensors or detectors, to be used for fault passage indication purposes. Requirements and proposals for the IEC 61850 series data model extensions to support fault passage indicators applications

JB/T 11205-2011 直流漏电流传感器

本标准规定了穿孔式直流漏电流传感器(以下简称漏电流传感器)的术语和定义、产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于将直流正负馈线间的漏电流变换为直流电压(电流),在测量范围内输出是对应输入的函数的电流传感器。 本标准适用于测量1000mA及以下的直流小电流的漏电流

Direct-current leakage current sensor

ASTM F2070-00(2022 压力传感器、压差传感器、压力传感器、电气传感器和光纤传感器

Standard Specification for Transducers, Pressure and Differential, Pressure, Electrical and Fiber-Optic

JB/T 7490-2007 霍尔电流传感器

本标准规定了霍尔电流传感器的分类、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于采用霍尔元件制作的电流传感器

Hall effect current sensor

ANSI/IEEE C37.92:2005 保护电压和电流传感器中继电器的模拟输入标准

Defines the interface between voltage or current tranducer systems or sensing systems with analog electronic outputs, and suitably designed protective

Standard for Analog Inputs to Protective Relays from Electronic Voltage and Current Transducers

SJ 20790-2000 电流电压传感器总规范

本规范规定了军用电流电压传感器和电压传感器的通用要求、质量保证规定和试验方法等。 本规范主要适用于其传感器输出与被测电流与电压成线性关系的传感器。其它传感器也可参照采用

General specification for current and voltage sensors

GJB 8354-2015 电流电压传感器通用规范

TB/T 2763-2009 机车车辆用电流传感器和电压传感器

本标准规定了铁道机车车辆用电流传感器和电压传感器的技术要求、试验方法、检验规则及产品标志、包装、运输和储存等。 本标准适用于铁道机车车辆上对直流、交流、脉流的电流或电压进行测量的电流传感器和电压传感器。 本标准也可适用于地铁、轻轨等其他轨道交通车辆上的电流传感器和电压传感器

On-board current transducer and voltage transducer for rolling stock

GOST R 56750-2015 交流电测量设备. 特殊要求. 连接电压和电流低功率传感器 (电子式互感器) 的模拟输入仪表

Electricity metering equipment (a.c.). Particular requirements. Meters with analog inputs connected to the low-power sensor (electronic transformers) of voltage and current

BS EN 62689-1:2016 故障通道指示用电流和电压传感器或检测器. 通用原则和要求

Current and voltage sensors or detectors, to be used for fault passage indication purposes. General principles and requirements

GOST R 8.669-2009 国家测量统一性保证体系.压电感应及涡电流震动传感器振动仪.鉴定方法及手段

State system for ensuring the uniformity of measurements. Vibrometers with piezoelectric, induction and eddy current vibrations transducers. Methods of verification

GB/T 41135.1-2021 故障路径指示用电流和电压传感器或探测器 第1部分:通用原理和要求

Current and voltage sensors or detectors, to be used for fault passage indication purposes—Part 1: General principles and requirements

GB/T 41135.2-2021 故障路径指示用电流和电压传感器或探测器 第2部分:系统应用

Current and voltage sensors or detectors, to be used for fault passage indication purposes—Part 2: System aspects

IEC 62689-2:2016 电流和电压传感器或检测器 用于故障通道指示用途第2部分:系统方面

This part of IEC 62689 describes electric phenomena and electric system behaviour during faults@ according to the most widely diffused distribution

Current and voltage sensors or detectors, to be used for fault passage indication purposes - Part 2: System aspects

IEC 62689-1:2016 电流和电压传感器或检测器 用于故障通道指示用途第1部分:一般原则和要求

This part of IEC 62689 defines the minimum requirements (therefore performances) and consequent classification and tests (with the exception

Current and voltage sensors or detectors, to be used for fault passage indication purposes - Part 1: General principles and requirements

BS PD IEC/TR 62689-100:2016 故障通道指示用电流和电压传感器或检测器. 支持断层通道指示应用的IEC 61850系列数据模型扩展要求和建议

Current and voltage sensors or detectors, to be used for fault passage indication purposes. Requirements and proposals for the IEC 61850 series data model extensions to support fault passage indicators applications

JB/T 11205-2011 直流漏电流传感器

本标准规定了穿孔式直流漏电流传感器(以下简称漏电流传感器)的术语和定义、产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于将直流正负馈线间的漏电流变换为直流电压(电流),在测量范围内输出是对应输入的函数的电流传感器。 本标准适用于测量1000mA及以下的直流小电流的漏电流

Direct-current leakage current sensor

ASTM F2070-00(2022 压力传感器、压差传感器、压力传感器、电气传感器和光纤传感器

Standard Specification for Transducers, Pressure and Differential, Pressure, Electrical and Fiber-Optic

JB/T 7490-2007 霍尔电流传感器

本标准规定了霍尔电流传感器的分类、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于采用霍尔元件制作的电流传感器

Hall effect current sensor

编辑:北检院编辑部

我们的优势

选择北检院的六大理由

📚

CMA/CNAS 双认证

旗下实验室具备国家认证认可监督管理委员会CMA资质认定及中国合格评定国家认可委员会CNAS实验室认可,检测报告具有国际公信力。

🔬

1000+ 台套先进设备

配备扫描电镜、气质联用仪、电感耦合等离子体质谱仪等国际先进检测仪器,确保数据精准可靠。

🏢

15000+ 平米实验室

拥有规模化专业检测基地,涵盖材料、化工、食品、环境等多个专业实验室,满足多领域检测需求。

👥

资深技术团队

汇聚材料科学、化学分析、环境工程等领域专家,拥有10年+行业经验,提供专业可靠的检测分析服务。

⏱

快速响应机制

标准检测周期短至3个工作日,加急服务24小时出具报告,全程一对一工程师跟进,确保高效交付。

🌎

全国服务网络

总部位于北京,山东设立分部,服务覆盖全国,为20万+客户提供便捷的一站式检测解决方案。

荣誉资质

旗下实验室资质荣誉

CMA 检验检测机构资质认定

CMA 检验检测机构资质认定

国家认证认可监督管理委员会颁发,具备向社会出具具有证明作用数据的资质。

CNAS 实验室认可证书

CNAS 实验室认可证书

中国合格评定国家认可委员会认可,检测结果获国际互认,具有国际公信力。

ISO 质量管理体系认证

ISO 质量管理体系认证

通过ISO 质量管理体系认证,管理体系实现规范化、标准化。

绿色低碳诚信示范创建企业

绿色低碳诚信示范创建企业

荣获绿色低碳诚信示范创建企业称号,践行可持续发展理念,推动绿色低碳转型,助力"双碳"目标实现。

北京市创新型中小企业

北京市"创新型"中小企业

经北京市经济和信息化局认定的创新型中小企业,具备较强创新能力与较高专业化水平,是优质中小企业梯度培育体系的重要基础力量。

北京市专精特新中小企业

北京市"专精特新"中小企业

经北京市经济和信息化局认定的专精特新中小企业,具备专业化、精细化、特色化、新颖化发展特征,在细分领域具有较强竞争优势。

查看全部资质

仪器设备

国际先进检测仪器,确保检测数据精准可靠

查看全部设备

检测流程

标准化流程,高效交付

01

需求沟通

客户提交检测需求,技术顾问一对一沟通,明确检测项目与标准。

➔
02

样品寄送

客户按照规范要求寄送样品,实验室确认样品状态与数量。

➔
03

实验检测

专业工程师按照标准方法进行检测分析,全程质量控制。

➔
04

数据审核

检测数据经多级审核,确保结果准确、可靠、可追溯。

➔
05

报告出具

出具检测报告,支持电子版与纸质版,快递送达。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通