ISO/TR 11647:1996 聚乙烯管材和管件的可熔焊性
This Technical Report gives guidance on methods for the examination of the fusion compatibility of two PE materials when jointed. A basic "material
Fusion compatibility of polyethylene (PE) pipes and fittings
GB/T 13021-1991 聚乙烯管材和管件炭黑含量的测定(热失重法)
本标准规定了聚乙烯管材和管件炭黑含量的测定方法。 本标准适用于聚乙烯管材和管件，也适用于聚烯烃管材和管件及制造管材和管件所用原料的炭黑含量的测定
Determination for the carbon black content of polyethylene pipes and fittings by calcination and pyrolysis
ISO 8772:1991 埋地污废水排放用高密度聚乙烯管材和管件 规范
This International Standard specifies requirements for high-density polyethylene (PE-HD) pipes, fittings and joints with nominal outside diameters
High density polyethylene (PE-HD) pipes and fittings for buried drainage and sewerage systems; specifications
GB/T 19807-2005 塑料管材和管件 聚乙烯管材和电熔管件 组合试件的制备
本标准规定了聚乙烯（PE）管材或插口管件与电熔管件（例如：承口管件如套筒，或鞍形管件）组合试件的制备方法。本标准规定了组合试件制备准则，包括环境温度、熔接条件、管材和管件的尺寸、管材形状等参数，并考虑了相关产品标准中对使用条件的限制
Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene(PE)pipe and an electrofusion fitting
ISO/TS 10839:2000 供应气体燃料的聚乙烯管材和管件 设计、搬运和安装实施规范
This Technical Specification presents a code of practice dealing with polyethylene (PE) pipes and fittings for buried pipeline systems outside
Polyethylene pipes and fittings for the supply of gaseous fuels - Code of practice for design, handling and installation
ISO 8770:1991 建筑物内污废水排放(低温和高温)用高密度聚乙烯管材和管件 规范
High-density polyethylene (PE-HD) pipes and fittings for soil and waste discharge (low and high temperature) systems inside buildings; specifications
ISO 13953:2001 聚乙烯管材和管件 拉申强度的测定和熔接对接接头试件的失效模型
This International Standard describes a test method for determination of the tensile strength and tensile failure mode of butt-fused polyethylene (PE
Polyethylene(PE) pipes and fittings - Determination of the tensile strengt and failure mode of test pieces from a butt-fused joint
GB/T 9643-1988 聚乙烯(PE)管材和管件 熔体流动速率试验方法
本标准规定了测定由聚乙烯制成的管材和管件熔体流动速率的方法。 本标准适用于所有聚乙烯（PE）管材和管件，不论其材料类型和最终用途
Polyethylene (PE) pipes and fittings--Determination of melt flow rate
GB/T 9642-1988 聚乙烯(PE)管材和管件 根据聚乙烯公称密度和熔体流动速率命名的方法
本标准规定了以制造聚乙烯管材和管件所用的原料命名该聚乙烯管材和管件的方法。 本标准适用于各种用途的聚乙烯管材和管件。其辅料仅包括抗氧剂、稳定剂和必须的料。 本标准不适用于填有玻璃纤维及石棉纤维的聚乙烯管材和管件
Polyethylene (PE) pipes and fittings--Designation of polyethylene, based on nominal density and melt flow rate
GOST R ISO 2507-2:2015 热塑性塑料管道和管件. 维卡软化温度. 第2部分. 未增塑聚氯乙烯, 氯化聚氯乙烯管材和管件和耐高冲击聚氯乙烯管的试验条件
Thermoplastics pipes and fittings. Vicat softening temperature. Part 2. Test conditions for unplasticized polyvinylchloride, chlorinated polyvinylchloride pipes and fittings and high impact polyvinylchloride pipes
STAS SR ISO 3663:1995 聚乙烯压力管材和管件，米制系列，法兰尺寸
Prezentul Standard Interna?ional stabile?te dimensiunile principale ale flan?elor libere utilizate ca gulere de sudare prin fuziune cap la cap sau cu
`Polye?hylene (PE) pressure pipes and fitings, metric series Dirnensions of flanges
GB/T 19810-2005 聚乙烯(PE)管材和管件 热熔对接接头 拉伸强度和破坏形式的测定
本标准规定了测定聚乙烯（PE）热熔对接组件的拉伸强度和拉伸破坏形式的试验方法。 本方法适用于公称外径不小于90mm的聚乙烯（PE）管材与管材或管材与管件插口端的热熔对接接头。 本方法可以与其他测试方法结合使用，来判定对熔焊接接头的质量
Polyethylene(PE)pipe and fittings.Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
ISO 4439:1979 硬聚氯乙烯(PVC)管材和管件 密度的测定和规范
The density of an unplasticised polyvinylchloride (PVC-U) pipe or -fitting, measured by the method described in ISO 1183, shall be between the limits
Unplasticized polyvinyl chloride (PVC) pipes and fittings; Determination and specification of density
ISO 3514:1976 氯化聚氯乙烯(CPVC)管材和管件 密度的测定和规范
The density at 23 鳦 of chlorinated polyvinylchlorid - (PVC-C)-pipes or -fittings, measured by the method described in ISO 1183, shall be between
Chlorinated polyvinyl chloride (CPVC) pipes and fittings; Specification and determination of density
TCVN 6038-1995 未增塑聚氯乙烯(PVC)管材和管件.密度的测定和规范
Unplasticized polyvinyl chloride (PVC) pipes and fittings.Determination and specification of density
ISO/TR 11647:1996 聚乙烯管材和管件的可熔焊性
This Technical Report gives guidance on methods for the examination of the fusion compatibility of two PE materials when jointed. A basic "material
Fusion compatibility of polyethylene (PE) pipes and fittings
GB/T 13021-1991 聚乙烯管材和管件炭黑含量的测定(热失重法)
本标准规定了聚乙烯管材和管件炭黑含量的测定方法。 本标准适用于聚乙烯管材和管件，也适用于聚烯烃管材和管件及制造管材和管件所用原料的炭黑含量的测定
Determination for the carbon black content of polyethylene pipes and fittings by calcination and pyrolysis
ISO 8772:1991 埋地污废水排放用高密度聚乙烯管材和管件 规范
This International Standard specifies requirements for high-density polyethylene (PE-HD) pipes, fittings and joints with nominal outside diameters
High density polyethylene (PE-HD) pipes and fittings for buried drainage and sewerage systems; specifications
GB/T 19807-2005 塑料管材和管件 聚乙烯管材和电熔管件 组合试件的制备
本标准规定了聚乙烯（PE）管材或插口管件与电熔管件（例如：承口管件如套筒，或鞍形管件）组合试件的制备方法。本标准规定了组合试件制备准则，包括环境温度、熔接条件、管材和管件的尺寸、管材形状等参数，并考虑了相关产品标准中对使用条件的限制
Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene(PE)pipe and an electrofusion fitting
ISO/TS 10839:2000 供应气体燃料的聚乙烯管材和管件 设计、搬运和安装实施规范
This Technical Specification presents a code of practice dealing with polyethylene (PE) pipes and fittings for buried pipeline systems outside
Polyethylene pipes and fittings for the supply of gaseous fuels - Code of practice for design, handling and installation
ISO 8770:1991 建筑物内污废水排放(低温和高温)用高密度聚乙烯管材和管件 规范
High-density polyethylene (PE-HD) pipes and fittings for soil and waste discharge (low and high temperature) systems inside buildings; specifications
ISO 13953:2001 聚乙烯管材和管件 拉申强度的测定和熔接对接接头试件的失效模型
This International Standard describes a test method for determination of the tensile strength and tensile failure mode of butt-fused polyethylene (PE
Polyethylene(PE) pipes and fittings - Determination of the tensile strengt and failure mode of test pieces from a butt-fused joint
GB/T 9643-1988 聚乙烯(PE)管材和管件 熔体流动速率试验方法
本标准规定了测定由聚乙烯制成的管材和管件熔体流动速率的方法。 本标准适用于所有聚乙烯（PE）管材和管件，不论其材料类型和最终用途
Polyethylene (PE) pipes and fittings--Determination of melt flow rate
GB/T 9642-1988 聚乙烯(PE)管材和管件 根据聚乙烯公称密度和熔体流动速率命名的方法
本标准规定了以制造聚乙烯管材和管件所用的原料命名该聚乙烯管材和管件的方法。 本标准适用于各种用途的聚乙烯管材和管件。其辅料仅包括抗氧剂、稳定剂和必须的料。 本标准不适用于填有玻璃纤维及石棉纤维的聚乙烯管材和管件
Polyethylene (PE) pipes and fittings--Designation of polyethylene, based on nominal density and melt flow rate
GOST R ISO 2507-2:2015 热塑性塑料管道和管件. 维卡软化温度. 第2部分. 未增塑聚氯乙烯, 氯化聚氯乙烯管材和管件和耐高冲击聚氯乙烯管的试验条件
Thermoplastics pipes and fittings. Vicat softening temperature. Part 2. Test conditions for unplasticized polyvinylchloride, chlorinated polyvinylchloride pipes and fittings and high impact polyvinylchloride pipes
STAS SR ISO 3663:1995 聚乙烯压力管材和管件，米制系列，法兰尺寸
Prezentul Standard Interna?ional stabile?te dimensiunile principale ale flan?elor libere utilizate ca gulere de sudare prin fuziune cap la cap sau cu
`Polye?hylene (PE) pressure pipes and fitings, metric series Dirnensions of flanges
GB/T 19810-2005 聚乙烯(PE)管材和管件 热熔对接接头 拉伸强度和破坏形式的测定
本标准规定了测定聚乙烯（PE）热熔对接组件的拉伸强度和拉伸破坏形式的试验方法。 本方法适用于公称外径不小于90mm的聚乙烯（PE）管材与管材或管材与管件插口端的热熔对接接头。 本方法可以与其他测试方法结合使用，来判定对熔焊接接头的质量
Polyethylene(PE)pipe and fittings.Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
ISO 4439:1979 硬聚氯乙烯(PVC)管材和管件 密度的测定和规范
The density of an unplasticised polyvinylchloride (PVC-U) pipe or -fitting, measured by the method described in ISO 1183, shall be between the limits
Unplasticized polyvinyl chloride (PVC) pipes and fittings; Determination and specification of density
ISO 3514:1976 氯化聚氯乙烯(CPVC)管材和管件 密度的测定和规范
The density at 23 鳦 of chlorinated polyvinylchlorid - (PVC-C)-pipes or -fittings, measured by the method described in ISO 1183, shall be between
Chlorinated polyvinyl chloride (CPVC) pipes and fittings; Specification and determination of density
TCVN 6038-1995 未增塑聚氯乙烯(PVC)管材和管件.密度的测定和规范
Unplasticized polyvinyl chloride (PVC) pipes and fittings.Determination and specification of density
编辑：北检院编辑部
