GB/T 9643-1988 聚乙烯(PE)管材和管件 熔体流动速率试验方法
本标准规定了测定由聚乙烯制成的管材和管件熔体流动速率的方法。 本标准适用于所有聚乙烯（PE）管材和管件，不论其材料类型和最终用途
Polyethylene (PE) pipes and fittings--Determination of melt flow rate
GB/T 19810-2005 聚乙烯(PE)管材和管件 热熔对接接头 拉伸强度和破坏形式的测定
本标准规定了测定聚乙烯（PE）热熔对接组件的拉伸强度和拉伸破坏形式的试验方法。 本方法适用于公称外径不小于90mm的聚乙烯（PE）管材与管材或管材与管件插口端的热熔对接接头。 本方法可以与其他测试方法结合使用，来判定对熔焊接接头的质量
Polyethylene(PE)pipe and fittings.Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
GB/T 9642-1988 聚乙烯(PE)管材和管件 根据聚乙烯公称密度和熔体流动速率命名的方法
本标准规定了以制造聚乙烯管材和管件所用的原料命名该聚乙烯管材和管件的方法。 本标准适用于各种用途的聚乙烯管材和管件。其辅料仅包括抗氧剂、稳定剂和必须的料。 本标准不适用于填有玻璃纤维及石棉纤维的聚乙烯管材和管件
Polyethylene (PE) pipes and fittings--Designation of polyethylene, based on nominal density and melt flow rate
ISO 10147:1994 交联聚乙烯(PE-X)管材和管件 用凝胶含量测定交联度
Pipes and fittings made of crosslinked polyethylene (PE-X) - Estimation of the degree of crosslinking by determination of the gel content
ISO 10147:2004 交联聚乙烯(PE-X)管材和管件.通过测定凝胶含量估算交联度
This International Standard specifies a method for the assessment of the degree of crosslinking in polyethylene (PE-X) pipes and fittings
Pipes and fittings made of crosslinked polyethylene (PE-X) - Estimation of the degree of crosslinking by determination of the gel content
NF T54-087*NF EN ISO 10147:2013 交联聚乙烯(PE-X)管材和管件.通过测定凝胶含量估算交联度
Pipes and fittings made of crosslinked polyethylene (PE-X) - Estimation of the degree of crosslinking by determination of the gel content
ISO 10147:2011 交联聚乙烯(PE-X)管材和管件.通过测定凝胶含量估算交联度
Pipes and fittings made of crosslinked polyethylene (PE-X) - Estimation of the degree of crosslinking by determination of the gel content
ISO 3663:1976 聚乙烯(PE)压力管材和管件 公制系列 法兰尺寸
Specifies the principal dimensions of loose backing flanges for butt or socket fusion welded flange adaptors and clamping flanges. It applies
Polyethylene (PE) pressure pipes and fittings, metric series; Dimensions of flanges
ISO 3501:1976 聚乙烯(PE)压力管材和管件间的装配接头 抗拉拔试验
Specifies a method for checking the ability of assembled pipe-fitting-joints to withstand longitudinal tensile stresses. The test is carried out
Assembled joints between fittings and polyethylene (PE) pressure pipes; Test of resistance to pull out
STAS SR ISO 3501:1995 聚乙烯（PE）压力管材和管件间的装配街头．抗拉拔实验
Prezentul Standard Interna?ional stabile?te metoda de verificare a rezisten?ei ?a trac?iune longitudinal? a asambl?rilor (cu excep?ia asambl?rilor
Assembled joints between fittings and polyethylene (PE) pressure pipes - Test of resistbnce to pull out
ISO 3501:2015 聚乙烯(PE)压力管材和管件间的装配接头 抗拉拔试验
Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force
STAS SR ISO 3458:1995 聚乙烯（PE）压力管材和管件间的组装街头．内压防漏测试
ASAMBL?RI ?NTRE FITINGURI ?l ?EVI DE POLIETILEN? (PE) SUB PRESIUNE ?ncercarea de etan?eitate la presiune interioar
Assembled jpints between fittings polyethylene (PE) pressure pipes -Test of leakproofness under internal pressure
ISO 3458:2015 聚乙烯(PE)压力管材和管件间的装配接头 内压密封试验
Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for leaktightness under internal pressure
ISO 3458:1976 聚乙烯(PE)压力管材和管件间的装配接头 内压密封试验
Specification of test method and requirements for leakproofness of assembled joints between fittings and polyethylene-(PE-) pipes, when submitted
Assembled joints between fittings and polyethylene (PE) pressure pipes ; Test of leakproofness under internal pressure
GB/T 19809-2005 塑料管材和管件 聚乙烯(PE)管材/管材或管材/管件热熔对接组件的制备
本标准规定了聚乙烯管材与管材或管材与管件插口端热熔对接组件的制备方法。 考虑到相关产品尺寸中规定的使用限制条件和所用管材的类型，本标准规定了焊接参数，如环境温度、接头几何尺寸和熔接参数等。 焊接环境的不同会影响到待测组件的连接性能。根据生产商的说明书和/或相关标准，制备
Plastics pipes and fittings.Preparation of polyethylene(PE)pipe/pipe or pipe/fitting test piece assemblies by butt fusion
GB/T 9643-1988 聚乙烯(PE)管材和管件 熔体流动速率试验方法
本标准规定了测定由聚乙烯制成的管材和管件熔体流动速率的方法。 本标准适用于所有聚乙烯（PE）管材和管件，不论其材料类型和最终用途
Polyethylene (PE) pipes and fittings--Determination of melt flow rate
GB/T 19810-2005 聚乙烯(PE)管材和管件 热熔对接接头 拉伸强度和破坏形式的测定
本标准规定了测定聚乙烯（PE）热熔对接组件的拉伸强度和拉伸破坏形式的试验方法。 本方法适用于公称外径不小于90mm的聚乙烯（PE）管材与管材或管材与管件插口端的热熔对接接头。 本方法可以与其他测试方法结合使用，来判定对熔焊接接头的质量
Polyethylene(PE)pipe and fittings.Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
GB/T 9642-1988 聚乙烯(PE)管材和管件 根据聚乙烯公称密度和熔体流动速率命名的方法
本标准规定了以制造聚乙烯管材和管件所用的原料命名该聚乙烯管材和管件的方法。 本标准适用于各种用途的聚乙烯管材和管件。其辅料仅包括抗氧剂、稳定剂和必须的料。 本标准不适用于填有玻璃纤维及石棉纤维的聚乙烯管材和管件
Polyethylene (PE) pipes and fittings--Designation of polyethylene, based on nominal density and melt flow rate
ISO 10147:1994 交联聚乙烯(PE-X)管材和管件 用凝胶含量测定交联度
Pipes and fittings made of crosslinked polyethylene (PE-X) - Estimation of the degree of crosslinking by determination of the gel content
ISO 10147:2004 交联聚乙烯(PE-X)管材和管件.通过测定凝胶含量估算交联度
This International Standard specifies a method for the assessment of the degree of crosslinking in polyethylene (PE-X) pipes and fittings
Pipes and fittings made of crosslinked polyethylene (PE-X) - Estimation of the degree of crosslinking by determination of the gel content
NF T54-087*NF EN ISO 10147:2013 交联聚乙烯(PE-X)管材和管件.通过测定凝胶含量估算交联度
Pipes and fittings made of crosslinked polyethylene (PE-X) - Estimation of the degree of crosslinking by determination of the gel content
ISO 10147:2011 交联聚乙烯(PE-X)管材和管件.通过测定凝胶含量估算交联度
Pipes and fittings made of crosslinked polyethylene (PE-X) - Estimation of the degree of crosslinking by determination of the gel content
ISO 3663:1976 聚乙烯(PE)压力管材和管件 公制系列 法兰尺寸
Specifies the principal dimensions of loose backing flanges for butt or socket fusion welded flange adaptors and clamping flanges. It applies
Polyethylene (PE) pressure pipes and fittings, metric series; Dimensions of flanges
ISO 3501:1976 聚乙烯(PE)压力管材和管件间的装配接头 抗拉拔试验
Specifies a method for checking the ability of assembled pipe-fitting-joints to withstand longitudinal tensile stresses. The test is carried out
Assembled joints between fittings and polyethylene (PE) pressure pipes; Test of resistance to pull out
STAS SR ISO 3501:1995 聚乙烯（PE）压力管材和管件间的装配街头．抗拉拔实验
Prezentul Standard Interna?ional stabile?te metoda de verificare a rezisten?ei ?a trac?iune longitudinal? a asambl?rilor (cu excep?ia asambl?rilor
Assembled joints between fittings and polyethylene (PE) pressure pipes - Test of resistbnce to pull out
ISO 3501:2015 聚乙烯(PE)压力管材和管件间的装配接头 抗拉拔试验
Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force
STAS SR ISO 3458:1995 聚乙烯（PE）压力管材和管件间的组装街头．内压防漏测试
ASAMBL?RI ?NTRE FITINGURI ?l ?EVI DE POLIETILEN? (PE) SUB PRESIUNE ?ncercarea de etan?eitate la presiune interioar
Assembled jpints between fittings polyethylene (PE) pressure pipes -Test of leakproofness under internal pressure
ISO 3458:2015 聚乙烯(PE)压力管材和管件间的装配接头 内压密封试验
Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for leaktightness under internal pressure
ISO 3458:1976 聚乙烯(PE)压力管材和管件间的装配接头 内压密封试验
Specification of test method and requirements for leakproofness of assembled joints between fittings and polyethylene-(PE-) pipes, when submitted
Assembled joints between fittings and polyethylene (PE) pressure pipes ; Test of leakproofness under internal pressure
GB/T 19809-2005 塑料管材和管件 聚乙烯(PE)管材/管材或管材/管件热熔对接组件的制备
本标准规定了聚乙烯管材与管材或管材与管件插口端热熔对接组件的制备方法。 考虑到相关产品尺寸中规定的使用限制条件和所用管材的类型，本标准规定了焊接参数，如环境温度、接头几何尺寸和熔接参数等。 焊接环境的不同会影响到待测组件的连接性能。根据生产商的说明书和/或相关标准，制备
Plastics pipes and fittings.Preparation of polyethylene(PE)pipe/pipe or pipe/fitting test piece assemblies by butt fusion
编辑：北检院编辑部
