摩托车光信号装置检测

📅 发布时间:2024-05-27 👤 来源:北检院 👁 阅读:

GB 17510-1998 性能

本标准规定了摩托车和轻便摩托车用前位灯、后位灯、制动灯、转向信号灯和后牌照灯的配光性能要求、配光性能和光色的测量方法以及检验规定。 本标准适用于摩托车和轻便摩托车用前位灯、后位灯、制动灯、转向信号灯和后牌照灯。 在本标准中,上述各种信号灯也称为装置

Photometric characteristics of light-signalling devices for motorcycles

GB 17510-2008 性能

本标准规定了摩托车和轻便摩托车用前位灯、后位灯、制动灯、转向信号灯和后牌照灯有关配光性能的要求、试验方法和检验规则等。 本标准适用于摩托车和轻便摩托车用前位灯、后位灯、制动灯、转向信号灯和后牌照灯。 在本标准中,上述各种信号灯也称为装置

Photometric characteristics of light-signalling devices for motorcycles

GB 18100-2000 两轮及轻便照明和的安规定

本标准规定了两轮摩托车及轻便摩托车照明和光信号装置的安装一般技术要求、特殊规定、试验方法及检验规则等。 本标准适用于两轮摩托车及轻便摩托车(L1、L3类

Provisions for installation of two wheel motorcycle and moped lighting and light-signalling devices

ISO 10355:2004 轻便.照明和的定位

This International Standard specifies the requirements for the positioning of lighting and light-signalling devices when fitted to a moped, as defined

Mopeds - Positioning of lighting and light-signalling devices

ISO 11460:2007 两轮.照明和的定位

This International Standard specifies the requirements for the positioning of lighting and light-signalling devices when fitted to a two-wheeled

Two-wheeled motorcycles - Positioning of lighting and light-signalling devices

ISO 11460:1993 两轮 照明和的定位

Specifies the requirements (position and orientation) for the main-beam headlamp, dipped-beam headlamp, front position lamp, side and rear

Two-wheeled motorcycles; positioning of lighting and light-signalling devices

ISO 10355:1994 轻便 照明和的定位

Mopeds - Positioning of lighting and light-signalling devices

BS ISO 11460:2007 两轮.照明和的位控制

This International Standard specifies the requirements for the positioning of lighting and light-signalling devices when fitted to a two-wheeled

Two-wheeled motorcycles - Positioning of lighting and light-signalling devices

GB 18100.3-2010 照明和的安规定 第3部分:三轮

GB 18100的本部分规定了三轮轻便摩托车,边三轮摩托车及正三轮摩托车照明和光信号装置安装的要求、试验方法和特别要求等。 本部分适用于三轮轻便摩托车,边三轮摩托车及正三轮摩托车(L2、L4、L5

Provisions for installation of lighting and light-signalling devices for motorcycles.Part 3:Three-wheel motorcycles

GB 18100.1-2010 照明和的安规定 第1部分:两轮

GB 18100的本部分规定了两轮摩托车(L3类)照明和光信号装置安装的要求及特别要求等。 本部分适用于两轮摩托车

Provisions for installation of lighting and light-signaling devices for motorcycles.Part 1:Two wheels motorcycle

SANS 20074:2000 轻便的认证的统一规定

Applies to the approval of two-wheeled power-driven vehicles without side-car, having a maximum design speed not exceeding 50 km/h and/or a cylinder

Uniform provisions concerning the approval of category L1 vehicles with regard to the installation of lighting and light-signalling devices

GB 18100.2-2010 照明和的安规定 第2部分:两轮轻便

GB 18100的本部分规定了两轮轻便摩托车(L1类)照明和光信号装置安装的要求及特别要求等。 本部分适用于两轮轻便摩托车

Provisions for installation of lighting and light-signaling devices for motorcycles.Part 2:Two wheels moped

TIS 2343-2007 用照明灯和的安

Installation of lighting and light.signalling devices for motorcycles

TCVN 6903-2001 道路辆.照明及的安.型式认证要求

Road vehicles.The installation of lighting and light-signalling devices of motorcycles.Requirements in type approval

GOST R 41.53-1999 关于审核L3类辆()的照明和灯情况的统一规定

Uniform provisions concerning the approval of L3 category vehicles (motor cycles) with regard to the installation of lighting and light-signalling devices

GB 17510-1998 性能

本标准规定了摩托车和轻便摩托车用前位灯、后位灯、制动灯、转向信号灯和后牌照灯的配光性能要求、配光性能和光色的测量方法以及检验规定。 本标准适用于摩托车和轻便摩托车用前位灯、后位灯、制动灯、转向信号灯和后牌照灯。 在本标准中,上述各种信号灯也称为装置

Photometric characteristics of light-signalling devices for motorcycles

GB 17510-2008 性能

本标准规定了摩托车和轻便摩托车用前位灯、后位灯、制动灯、转向信号灯和后牌照灯有关配光性能的要求、试验方法和检验规则等。 本标准适用于摩托车和轻便摩托车用前位灯、后位灯、制动灯、转向信号灯和后牌照灯。 在本标准中,上述各种信号灯也称为装置

Photometric characteristics of light-signalling devices for motorcycles

GB 18100-2000 两轮及轻便照明和的安规定

本标准规定了两轮摩托车及轻便摩托车照明和光信号装置的安装一般技术要求、特殊规定、试验方法及检验规则等。 本标准适用于两轮摩托车及轻便摩托车(L1、L3类

Provisions for installation of two wheel motorcycle and moped lighting and light-signalling devices

ISO 10355:2004 轻便.照明和的定位

This International Standard specifies the requirements for the positioning of lighting and light-signalling devices when fitted to a moped, as defined

Mopeds - Positioning of lighting and light-signalling devices

ISO 11460:2007 两轮.照明和的定位

This International Standard specifies the requirements for the positioning of lighting and light-signalling devices when fitted to a two-wheeled

Two-wheeled motorcycles - Positioning of lighting and light-signalling devices

ISO 11460:1993 两轮 照明和的定位

Specifies the requirements (position and orientation) for the main-beam headlamp, dipped-beam headlamp, front position lamp, side and rear

Two-wheeled motorcycles; positioning of lighting and light-signalling devices

ISO 10355:1994 轻便 照明和的定位

Mopeds - Positioning of lighting and light-signalling devices

BS ISO 11460:2007 两轮.照明和的位控制

This International Standard specifies the requirements for the positioning of lighting and light-signalling devices when fitted to a two-wheeled

Two-wheeled motorcycles - Positioning of lighting and light-signalling devices

GB 18100.3-2010 照明和的安规定 第3部分:三轮

GB 18100的本部分规定了三轮轻便摩托车,边三轮摩托车及正三轮摩托车照明和光信号装置安装的要求、试验方法和特别要求等。 本部分适用于三轮轻便摩托车,边三轮摩托车及正三轮摩托车(L2、L4、L5

Provisions for installation of lighting and light-signalling devices for motorcycles.Part 3:Three-wheel motorcycles

GB 18100.1-2010 照明和的安规定 第1部分:两轮

GB 18100的本部分规定了两轮摩托车(L3类)照明和光信号装置安装的要求及特别要求等。 本部分适用于两轮摩托车

Provisions for installation of lighting and light-signaling devices for motorcycles.Part 1:Two wheels motorcycle

SANS 20074:2000 轻便的认证的统一规定

Applies to the approval of two-wheeled power-driven vehicles without side-car, having a maximum design speed not exceeding 50 km/h and/or a cylinder

Uniform provisions concerning the approval of category L1 vehicles with regard to the installation of lighting and light-signalling devices

GB 18100.2-2010 照明和的安规定 第2部分:两轮轻便

GB 18100的本部分规定了两轮轻便摩托车(L1类)照明和光信号装置安装的要求及特别要求等。 本部分适用于两轮轻便摩托车

Provisions for installation of lighting and light-signaling devices for motorcycles.Part 2:Two wheels moped

TIS 2343-2007 用照明灯和的安

Installation of lighting and light.signalling devices for motorcycles

TCVN 6903-2001 道路辆.照明及的安.型式认证要求

Road vehicles.The installation of lighting and light-signalling devices of motorcycles.Requirements in type approval

GOST R 41.53-1999 关于审核L3类辆()的照明和灯情况的统一规定

Uniform provisions concerning the approval of L3 category vehicles (motor cycles) with regard to the installation of lighting and light-signalling devices

编辑:北检院编辑部

我们的优势

选择北检院的六大理由

📚

CMA/CNAS 双认证

旗下实验室具备国家认证认可监督管理委员会CMA资质认定及中国合格评定国家认可委员会CNAS实验室认可,检测报告具有国际公信力。

🔬

1000+ 台套先进设备

配备扫描电镜、气质联用仪、电感耦合等离子体质谱仪等国际先进检测仪器,确保数据精准可靠。

🏢

15000+ 平米实验室

拥有规模化专业检测基地,涵盖材料、化工、食品、环境等多个专业实验室,满足多领域检测需求。

👥

资深技术团队

汇聚材料科学、化学分析、环境工程等领域专家,拥有10年+行业经验,提供专业可靠的检测分析服务。

快速响应机制

标准检测周期短至3个工作日,加急服务24小时出具报告,全程一对一工程师跟进,确保高效交付。

🌎

全国服务网络

总部位于北京,山东设立分部,服务覆盖全国,为20万+客户提供便捷的一站式检测解决方案。

荣誉资质

旗下实验室资质荣誉

CMA 检验检测机构资质认定

CMA 检验检测机构资质认定

国家认证认可监督管理委员会颁发,具备向社会出具具有证明作用数据的资质。

CNAS 实验室认可证书

CNAS 实验室认可证书

中国合格评定国家认可委员会认可,检测结果获国际互认,具有国际公信力。

ISO 质量管理体系认证

ISO 质量管理体系认证

通过ISO 质量管理体系认证,管理体系实现规范化、标准化。

绿色低碳诚信示范创建企业

绿色低碳诚信示范创建企业

荣获绿色低碳诚信示范创建企业称号,践行可持续发展理念,推动绿色低碳转型,助力"双碳"目标实现。

北京市创新型中小企业

北京市"创新型"中小企业

经北京市经济和信息化局认定的创新型中小企业,具备较强创新能力与较高专业化水平,是优质中小企业梯度培育体系的重要基础力量。

北京市专精特新中小企业

北京市"专精特新"中小企业

经北京市经济和信息化局认定的专精特新中小企业,具备专业化、精细化、特色化、新颖化发展特征,在细分领域具有较强竞争优势。

查看全部资质

仪器设备

国际先进检测仪器,确保检测数据精准可靠

查看全部设备

检测流程

标准化流程,高效交付

01

需求沟通

客户提交检测需求,技术顾问一对一沟通,明确检测项目与标准。

02

样品寄送

客户按照规范要求寄送样品,实验室确认样品状态与数量。

03

实验检测

专业工程师按照标准方法进行检测分析,全程质量控制。

04

数据审核

检测数据经多级审核,确保结果准确、可靠、可追溯。

05

报告出具

出具检测报告,支持电子版与纸质版,快递送达。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验