GB/T 24924-2010 供水系统用弹性密封闸阀
本标准规定了弹性密封闸阀的术语和定义、结构形式和结构长度、技术要求、材料、试验方法、检验规则、标志和供货要求。 本标准适用于公称尺寸不大于DN300，公称压力不大于PN25，或公称尺寸大于DN300-DN800，公称压力不大于PN16；使用温度不大于80℃；法兰连接；供水系统用铁制闸阀的采购、设计
Resilient-seated gate valves for water supply service
GB/T 32290-2015 供水系统用弹性密封轻型闸阀
本标准规定了供水系统用弹性密封轻型闸阀(以下简称闸阀)的术语和定义、结构型式、技术要求、试验方法、检验规则、标志、供货要求和质量保征书。 本标准适用于球墨铸铁制弹性密封轻型闸阀。适用范围为公称压力不大于PN 16；介质为水，水温范围1 ℃~80 ℃；阀门全开时介质流速不超过4.9 m/s；公称尺寸
Reduced-wall, resilient-seated gate valves for water supply service
JWWA B120-2009 供水系统用弹性阀座闸阀
Resilient seated gate valves for water supply
AWWA C509-2009 供水服务用软密封闸阀
Resilient-Seated Gate Valves for Water Supply Service
AWWA C509-2001 水供应系统弹力闸式阀
This standard pertains to unannealed austenitic stainless-steel pipe that is longitudinal-seam or spiral-seam welded, 1/2 in. (13 mm) in nominal
Resilient-Seated Gate Valves for Water Supply Service
AWWA C515-2001 水供应系统弹力闸式阀
This standard describes reduced-wall, resilient-seated gate valves with nonrising stems (NRS) and outside screw-and-yoke (OS&Y) rising stems
Reduced-Wall, Resilient-Seated Gate Valves for Water Supply Service Second Edition
CNS 12795-1993 水道用弹性座封闸阀
本标准适用于标称口径 50mm 至 350mm 之水道用球状石墨铸铁弹性座封闸阀（以下简称阀
Resilient - Seated Gate Valves For Water Works
CJ/T 216-2013 给水排水用软密封闸阀
本标准规定了城镇给水排水用软密封闸阀(以下简称闸阀)的结构型式及尺寸、要求、试验方法、检验规则、标志和供货等。本标准适用于公称尺寸DN50~DN900(其中公称尺寸不大于DN400的,公称压力小于或等于PN25 ;公称尺寸大于DN400,且不大于DN900的,公称压力小于或等于PN16),最高使用
Resilient-seated gate valves for water supply and drainage service
AWWA C515-2009 供水服务用壁厚减小的软密封闸阀
Reduced-Wall, Resilient-Seated Gate Valves for Water Supply Service
CJ/T 216-2005 给排水用软密封闸阀
本标准规定了橡胶软密封闸阀(以下简称闸阀)的结构型式、要求、检验方法、检验规则、标志、包装、运输和贮存等基本要求。 本标准适用于公称压力PN0.6MPa～2.5MPa，公称通径DN50mm～800mm，球墨铸铁材质，城镇给排水用闸阀的设计、制造和验收
Resilient-seated gate valves for water supply and drainage service
AS 2638.2-2006 自来水工程用弹性座封闸阀
Sets out requirements for PN 16 and PN 25 metal-bodied resilient-seated gate valves for waterworks purposes, with a maximum operating temperature
Gate valves for waterworks purposes - Resilient seated
JWWA B122-2005 供水系统用球墨铸铁闸阀
Ductile cast iron gate valves for water supply
SANS 664-3:2009 水厂门楔及弹性密封阀.第3部分:弹性密封阀
Covers the requirements for the design and construction of resilient seal valves of pressure rating (PN) up to 2 500 kPa and of sizes up to 600 mm
Wedge gate and resilient seal valves for waterworks Part 3: Resilient seal valves
AS 681.2-2008 弹性密封件．供水和排水系统用管接头密封件的材料要求．热塑性弹性材料
Specifies requirements for materials used for moulded seals only of thermoplastic elastomers (TPE) used in joints of thermoplastic piping systems
Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Thermoplastic elastomers
DB34/T 1624-2011 铁制和铜制螺纹连接弹性密封闸阀
本标准规定了铁制和铜制螺纹连接弹性密封闸阀（以下简称螺纹软闸）的结构型式、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于： 公称压力不大于 PN16、公称尺寸不大于 DN100 的可锻铸铁螺纹软闸； 公称压力不大于 PN25、公称尺寸不大于 DN100 的球墨铸铁螺纹软闸
GB/T 24924-2010 供水系统用弹性密封闸阀
本标准规定了弹性密封闸阀的术语和定义、结构形式和结构长度、技术要求、材料、试验方法、检验规则、标志和供货要求。 本标准适用于公称尺寸不大于DN300，公称压力不大于PN25，或公称尺寸大于DN300-DN800，公称压力不大于PN16；使用温度不大于80℃；法兰连接；供水系统用铁制闸阀的采购、设计
Resilient-seated gate valves for water supply service
GB/T 32290-2015 供水系统用弹性密封轻型闸阀
本标准规定了供水系统用弹性密封轻型闸阀(以下简称闸阀)的术语和定义、结构型式、技术要求、试验方法、检验规则、标志、供货要求和质量保征书。 本标准适用于球墨铸铁制弹性密封轻型闸阀。适用范围为公称压力不大于PN 16；介质为水，水温范围1 ℃~80 ℃；阀门全开时介质流速不超过4.9 m/s；公称尺寸
Reduced-wall, resilient-seated gate valves for water supply service
JWWA B120-2009 供水系统用弹性阀座闸阀
Resilient seated gate valves for water supply
AWWA C509-2009 供水服务用软密封闸阀
Resilient-Seated Gate Valves for Water Supply Service
AWWA C509-2001 水供应系统弹力闸式阀
This standard pertains to unannealed austenitic stainless-steel pipe that is longitudinal-seam or spiral-seam welded, 1/2 in. (13 mm) in nominal
Resilient-Seated Gate Valves for Water Supply Service
AWWA C515-2001 水供应系统弹力闸式阀
This standard describes reduced-wall, resilient-seated gate valves with nonrising stems (NRS) and outside screw-and-yoke (OS&Y) rising stems
Reduced-Wall, Resilient-Seated Gate Valves for Water Supply Service Second Edition
CNS 12795-1993 水道用弹性座封闸阀
本标准适用于标称口径 50mm 至 350mm 之水道用球状石墨铸铁弹性座封闸阀（以下简称阀
Resilient - Seated Gate Valves For Water Works
CJ/T 216-2013 给水排水用软密封闸阀
本标准规定了城镇给水排水用软密封闸阀(以下简称闸阀)的结构型式及尺寸、要求、试验方法、检验规则、标志和供货等。本标准适用于公称尺寸DN50~DN900(其中公称尺寸不大于DN400的,公称压力小于或等于PN25 ;公称尺寸大于DN400,且不大于DN900的,公称压力小于或等于PN16),最高使用
Resilient-seated gate valves for water supply and drainage service
AWWA C515-2009 供水服务用壁厚减小的软密封闸阀
Reduced-Wall, Resilient-Seated Gate Valves for Water Supply Service
CJ/T 216-2005 给排水用软密封闸阀
本标准规定了橡胶软密封闸阀(以下简称闸阀)的结构型式、要求、检验方法、检验规则、标志、包装、运输和贮存等基本要求。 本标准适用于公称压力PN0.6MPa～2.5MPa，公称通径DN50mm～800mm，球墨铸铁材质，城镇给排水用闸阀的设计、制造和验收
Resilient-seated gate valves for water supply and drainage service
AS 2638.2-2006 自来水工程用弹性座封闸阀
Sets out requirements for PN 16 and PN 25 metal-bodied resilient-seated gate valves for waterworks purposes, with a maximum operating temperature
Gate valves for waterworks purposes - Resilient seated
JWWA B122-2005 供水系统用球墨铸铁闸阀
Ductile cast iron gate valves for water supply
SANS 664-3:2009 水厂门楔及弹性密封阀.第3部分:弹性密封阀
Covers the requirements for the design and construction of resilient seal valves of pressure rating (PN) up to 2 500 kPa and of sizes up to 600 mm
Wedge gate and resilient seal valves for waterworks Part 3: Resilient seal valves
AS 681.2-2008 弹性密封件．供水和排水系统用管接头密封件的材料要求．热塑性弹性材料
Specifies requirements for materials used for moulded seals only of thermoplastic elastomers (TPE) used in joints of thermoplastic piping systems
Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Thermoplastic elastomers
DB34/T 1624-2011 铁制和铜制螺纹连接弹性密封闸阀
本标准规定了铁制和铜制螺纹连接弹性密封闸阀（以下简称螺纹软闸）的结构型式、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于： 公称压力不大于 PN16、公称尺寸不大于 DN100 的可锻铸铁螺纹软闸； 公称压力不大于 PN25、公称尺寸不大于 DN100 的球墨铸铁螺纹软闸
编辑：北检院编辑部
