腐蚀气体试验设备检测

GB/T 5170.11-2017 环境试验设备检验方法 第11部分:腐蚀气体试验设备

GB/T 5170的本部分规定了腐蚀气体试验设备(以下简称“设备”)的检验项目、检验用仪器及要求、检验负载、检验条件、检验方法、检验结果、检验周期等内容。 本部分适用于对GB/T 2423.19和GB/T 2423.20所用设备的检验。 本部分也适用于类似设备的检验

Inspection methods for environmental testing equipments.Part 11:Corrosive gas testing equipments

GB/T 5170.11-2008 电工电子产品环境试验设备检验方法.腐蚀气体试验设备

GB/T 5170的本部分规定了腐蚀气体试验设备的检验项目、检验用主要仪器及要求、检验负载、检验条件、检验方法、数据处理结果与检验结果、检验周期等内容。 本部分适用于电工电子产品腐蚀气体试验设备的首次检验/验收检验和周期检验。 本部分也适用于类似试验设备的检验

Inspection methods for environmental testing equipments for electric and electronic products.Corrosive gas testing equipments

GB/T 5170.11-1996 电工电子产品环境试验设备基本参数检定方法 腐蚀气体试验设备

本标准规定了腐蚀气体试验设备在进行周期检定时所涉及的检定项目、检定用仪器、测量点数量及布放位置、检定步骤及数据处理等。 本标准适用于对GB/T2423.19《电工电子产品基本环境试验规程试验Kc：接触点和连接件的二氧化硫试验方法》和GB/T2423.20《电工电子产品基本环境试验规程

Inspection methods for basic parameters of environmental testing equipments for electric and electronic products--Corrosive gas testing equipments

BS EN 60512-11-14:2003 电子设备用连接器.试验和测量.气候试验.流动单气体腐蚀试验

This part of IEC 60512, when required by the detail specification, is used for testing of connectors for electronic equipment. This test may also

Connectors for electronic equipment - Tests and measurements - Climatic tests - Flowing single gas corrosion test

BS EN 60512-11-7:2003 电子设备用连接器.试验和测量.流动混合气体腐蚀试验

This part of IEC 60512 defines a standard test method, Test 11 g, to assess the effects of a controlled atmosphere polluted by gases at very low

Connectors for electronic equipment - Tests and measurements - Flowing mixed gas corrosion test

NF C93-400-11-14*NF EN 60512-11-14:2006 电子设备连接器 试验和测量 第11-14部分：气候试验 试验11p：流动单气体腐蚀试验

Connectors for electronic equipment - Tests and measurements - Part 11-14 : climatic tests - Test 11p : flowing single gas corrosion test

IEC 60512-11-14-2003 电子设备连接器.试验和测量.第11-14部分:气候试验.试验11p:流动单气体腐蚀试验

Connectors for electronic equipment - Tests and measurements - Part 11-14: Climatic tests - Test 11p: Flowing single gas corrosion test

JIS Z 3196:1972 钎焊接头气体腐蚀试验方法

Method of gaseous corrosion test for brazed joint

GB/T 28416-2012 人工大气中的腐蚀试验.交替暴露在腐蚀性气体、中性盐雾及干燥环境中的加速腐蚀试验

本标准规定了两种加速腐蚀试验方法，用来评价含有金属材料的产品在有氯离子和腐蚀性气体显著影响的环境下的耐腐性，氯离子来自海洋环境中的氯化钠或者冬季道路上的去冰盐，腐蚀性气体来自工业或交通对空气的污染。 本标准规定了进行腐蚀加速试验的仪器和步骤。 这些方法尤其适合评价对腐蚀敏感的含有金属材料的产品的

Corrosion tests in artificial atmospheres.Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases,neutral salt-spray and drying

CTI STD-149-2000 腐蚀测试程序.腐蚀试片测试和测试设备

Corrosion Testing Procedures Corrosion Coupon Testing and Test Devices

DIN EN 60512-11-14:2004 电子设备用连接器.试验和测量.第11-14部分:气候试验.试验11p:流动单气体腐蚀试验

This part of IEC 60512 when required by the detail specification, is used for testing of connectors for electronic equipment. This test may also

Connectors for electronic equipment - Tests and measurements - Part 11-14: Climatic tests - Test 11p: Flowing single gas corrosion test (IEC 60512-11-14:2003); German version EN 60512-11-14:2003

IEC 60512-11-14:2003 电子设备用连接器.试验和测量.第11-14部分:气候试验.试验11p:流动单气体腐蚀试验

Defines a standard test method to assess the effects of controlled corrosion in industrial atmospheres, in a specified concentration of polluted gas

Connectors for electronic equipment - Tests and measurements - Part 11-14: Climatic tests; Test 11p: Flowing single gas corrosion test

BS EN 60512-11-6:2002 电子设备连接器.试验和测量.气候试验.试验11f.盐雾腐蚀

This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical

Connectors for electronic equipment - Tests and measurements - Climatic tests - Test 11f - Corrosion, salt mist

DIN EN 60512-11-7:2004 电子设备用连接器.试验和测量.第11-7部分:气候试验.试验11g:流动混合气体腐蚀试验

This section of IEC 60512-11 defines a standard test method to assess the effects of controlled atmosphere polluted by gases at very low concentration

Connectors for electronic equipment - Tests and measurements - Part 11-7: Climatic tests - Test 11g: Flowing mixed gas corrosion test (IEC 60512-11-7:2003); German version EN 60512-11-7:2003

EN 60512-11-14:1997 电子设备用连接器.试验和测量.第11-14部分:气候试验.试验11p:流动单一气体腐蚀试验

Electromechanical Components for Electronic Equipment; Basic Testing Procedures and Measuring Methods; Part 11: Climatic Tests; Section 14: Test 11p - Flowing Single Gas Corrosion Test

GB/T 5170.11-2017 环境试验设备检验方法 第11部分:腐蚀气体试验设备

GB/T 5170的本部分规定了腐蚀气体试验设备(以下简称“设备”)的检验项目、检验用仪器及要求、检验负载、检验条件、检验方法、检验结果、检验周期等内容。 本部分适用于对GB/T 2423.19和GB/T 2423.20所用设备的检验。 本部分也适用于类似设备的检验

Inspection methods for environmental testing equipments.Part 11:Corrosive gas testing equipments

GB/T 5170.11-2008 电工电子产品环境试验设备检验方法.腐蚀气体试验设备

GB/T 5170的本部分规定了腐蚀气体试验设备的检验项目、检验用主要仪器及要求、检验负载、检验条件、检验方法、数据处理结果与检验结果、检验周期等内容。 本部分适用于电工电子产品腐蚀气体试验设备的首次检验/验收检验和周期检验。 本部分也适用于类似试验设备的检验

Inspection methods for environmental testing equipments for electric and electronic products.Corrosive gas testing equipments

GB/T 5170.11-1996 电工电子产品环境试验设备基本参数检定方法 腐蚀气体试验设备

本标准规定了腐蚀气体试验设备在进行周期检定时所涉及的检定项目、检定用仪器、测量点数量及布放位置、检定步骤及数据处理等。 本标准适用于对GB/T2423.19《电工电子产品基本环境试验规程试验Kc：接触点和连接件的二氧化硫试验方法》和GB/T2423.20《电工电子产品基本环境试验规程

Inspection methods for basic parameters of environmental testing equipments for electric and electronic products--Corrosive gas testing equipments

BS EN 60512-11-14:2003 电子设备用连接器.试验和测量.气候试验.流动单气体腐蚀试验

This part of IEC 60512, when required by the detail specification, is used for testing of connectors for electronic equipment. This test may also

Connectors for electronic equipment - Tests and measurements - Climatic tests - Flowing single gas corrosion test

BS EN 60512-11-7:2003 电子设备用连接器.试验和测量.流动混合气体腐蚀试验

This part of IEC 60512 defines a standard test method, Test 11 g, to assess the effects of a controlled atmosphere polluted by gases at very low

Connectors for electronic equipment - Tests and measurements - Flowing mixed gas corrosion test

NF C93-400-11-14*NF EN 60512-11-14:2006 电子设备连接器 试验和测量 第11-14部分：气候试验 试验11p：流动单气体腐蚀试验

Connectors for electronic equipment - Tests and measurements - Part 11-14 : climatic tests - Test 11p : flowing single gas corrosion test

IEC 60512-11-14-2003 电子设备连接器.试验和测量.第11-14部分:气候试验.试验11p:流动单气体腐蚀试验

Connectors for electronic equipment - Tests and measurements - Part 11-14: Climatic tests - Test 11p: Flowing single gas corrosion test

JIS Z 3196:1972 钎焊接头气体腐蚀试验方法

Method of gaseous corrosion test for brazed joint

GB/T 28416-2012 人工大气中的腐蚀试验.交替暴露在腐蚀性气体、中性盐雾及干燥环境中的加速腐蚀试验

本标准规定了两种加速腐蚀试验方法，用来评价含有金属材料的产品在有氯离子和腐蚀性气体显著影响的环境下的耐腐性，氯离子来自海洋环境中的氯化钠或者冬季道路上的去冰盐，腐蚀性气体来自工业或交通对空气的污染。 本标准规定了进行腐蚀加速试验的仪器和步骤。 这些方法尤其适合评价对腐蚀敏感的含有金属材料的产品的

Corrosion tests in artificial atmospheres.Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases,neutral salt-spray and drying

DIN EN 60512-11-14:2004 电子设备用连接器.试验和测量.第11-14部分:气候试验.试验11p:流动单气体腐蚀试验

This part of IEC 60512 when required by the detail specification, is used for testing of connectors for electronic equipment. This test may also

Connectors for electronic equipment - Tests and measurements - Part 11-14: Climatic tests - Test 11p: Flowing single gas corrosion test (IEC 60512-11-14:2003); German version EN 60512-11-14:2003

IEC 60512-11-14:2003 电子设备用连接器.试验和测量.第11-14部分:气候试验.试验11p:流动单气体腐蚀试验

Defines a standard test method to assess the effects of controlled corrosion in industrial atmospheres, in a specified concentration of polluted gas

Connectors for electronic equipment - Tests and measurements - Part 11-14: Climatic tests; Test 11p: Flowing single gas corrosion test

CTI STD-149-2000 腐蚀测试程序.腐蚀试片测试和测试设备

Corrosion Testing Procedures Corrosion Coupon Testing and Test Devices

BS EN 60512-11-6:2002 电子设备连接器.试验和测量.气候试验.试验11f.盐雾腐蚀

This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical

Connectors for electronic equipment - Tests and measurements - Climatic tests - Test 11f - Corrosion, salt mist

DIN EN 60512-11-7:2004 电子设备用连接器.试验和测量.第11-7部分:气候试验.试验11g:流动混合气体腐蚀试验

This section of IEC 60512-11 defines a standard test method to assess the effects of controlled atmosphere polluted by gases at very low concentration

Connectors for electronic equipment - Tests and measurements - Part 11-7: Climatic tests - Test 11g: Flowing mixed gas corrosion test (IEC 60512-11-7:2003); German version EN 60512-11-7:2003

EN 60512-11-14:1997 电子设备用连接器.试验和测量.第11-14部分:气候试验.试验11p:流动单一气体腐蚀试验

Electromechanical Components for Electronic Equipment; Basic Testing Procedures and Measuring Methods; Part 11: Climatic Tests; Section 14: Test 11p - Flowing Single Gas Corrosion Test