穿刺器检测

JIS T 2601:1979 采血穿刺器

Blood lancet

JUS H.N8.208-1989 纸和纸板检测．抗穿刺性测定

Testing of board. Deterinination of puncture resistance

JIS T 3103:1979 穿刺针

Trocars

GB/T 24828-2009 穿刺根腐线虫检疫鉴定方法

本标准规定了对穿刺根腐线虫检疫和鉴定方法。本标准适用于花卉、观赏植物、蔬菜、烟草、果树、豆科、禾本科等多种植物根部土壤及栽培介质中的穿刺根腐线虫

Methods for quarantine and identification of Pratylenchus penetrans

DB35/T 1559-2016 柑橘半穿刺线虫检疫鉴定方法

本标准规定了柑橘半穿刺线虫鉴定依据、仪器用具及药品、现场检疫和抽样、实验室检疫鉴定、形态鉴定特征、结果判定以及样本和样品保存与处理。本标准适用于植物根系、土壤及生长介质中柑橘半穿刺线虫的检疫鉴定

YY/T 1710-2020 一次性使用腹部穿刺器

PN P50140-1992 纸板．穿刺阻力的测定

Niniejsza norma okre?la metod? oznaczania odporno?ci tektury na przebicie

Board Determination of puncture resistance

0 仪表板．穿刺阻力测定

Spracovatel': V?skumn? ústav papiera a celulózy, Bratislava, I?O 153 125, Ing. Ludmila Kristová, Ing. Ludmila Horňáková. Technická normaliza?n

KS M ISO 3036:2021 纸板.耐穿刺性的测定

Board — Determination of puncture resistance

KS M ISO 3036:2016 纸板耐穿刺性的测定

Board－Determination of puncture resistance

DB43/T 1727-2019 柑橘半穿刺线虫检疫鉴定LAMP法

YY/T 91148-1999 腰锥穿刺针

Lumbar puncture needles

YY/T 1148-2009 腰椎穿刺针

本标准规定了公称外径0.4mm~l.6mm，用于人体做蛛网膜下腔阻滞(简称腰椎麻醉)时进行穿刺，注射药液的腰椎穿刺针的要求

Spinal needle

YY/T 0328-2015 一次性使用动静脉穿刺器

本标准规定了一次性使用动静脉穿刺器(以下简称穿刺器)的要求,以保证与所配套的血路和血液处理系统相适应

A.V. fistula needle sets for single use

PN P04984-1988 防护手套穿刺阻力测定

Przedmiotem normy jest wyznaczanie odporno?ci na przek?ucie r?kawic ochronnych i materia?ów s?u??cych do ich wytwarzania, np. gum, tworzyw, tkanin i

Protective gloves Determination of puncture resistance

ANSI/ASTM D3763:2000 载荷-位移传感器测定塑料高速刺穿特性的方法(08.03)

This test method covers the determination of puncture properties of plastics, including films, over a range of test velocities. Test data obtained

Plastics Using Load and Displacement Sensors, Test Method for High-Speed Puncture Properties of (08.03)

NEMA C119.5-2009 电连接件器.额定电压小于等于600 V的绝缘刺穿连接器系统(低压高空捆扎电缆与绝缘和非绝缘线路导线)

Electric Connectors- Insulation Piercing Connector Systems, Rated 600 Volts or Less (Low-Voltage Aerial Bundled Cables and Insulated and Non-Insulated Line Wires)

ASTM F2132-01(2008 废弃医用针头和其他锋利物容器用材料的耐穿刺性标准规范

Standard Specification for Puncture Resistance of Materials Used in Containers for Discarded Medical Needles and Other Sharps

ASTM D3763-08 使用负载和位移传感器的塑料高速穿刺性能的标准测试方法

This test method is designed to provide load versus deformation response of plastics under essentially multiaxial deformation conditions at impact

Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors

ASTM D3763-18 使用负载和位移传感器的塑料高速穿刺性能的标准测试方法

Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors