试模检测

JJG(民航) 0060-2000 4TSJ60B00002型惯性导航模拟器测试仪检定规程

Verification Regulation of Model 4TSJ60B00002 INS Navigation Tester

JJG(电子) 31011-2007 DC/DC模块参数测试系统检定规程

JJG(电子) 04034-1989 GR1731M型模拟集成电路测试系统检定规程

JJG(电子) 04031-1989 9200型大规模集成电路测试系统检定规程

JJG(船舶) 23-1998 ITS9000系列超大规模集成电路测试系统检定规程

JJG(船舶) 22-1998 SID大规模数字集成电路测试系统检定规程

GJB/J 3524-1999 S10型大规模数字集成电路测试系统检定规程

GJB/J 3523-1999 S15型超大规模数字集成电路测试系统检定规程

ISO/TS 19016:2019 气瓶 - 复合结构的气缸和管 - 用于定期检查和测试的模态声发射（MAE）测试

Gas cylinders — Cylinders and tubes of composite construction — Modal acoustic emission (MAE) testing for periodic inspection and testing

T/CEEIA 470-2020 直流系统用剩余电流检测模块动作特性试验方法

本文件规定了对预期用于直流系统，额定电压不超过直流1000 V，额定电流不超过63 A的剩余电流检测模块（以下简称“DC-RCDU”）进行动作特性验证试验的一般要求。 注：本文件也提供了作为电压不超过直流1500 V的DC-RCDU动作特性验证的指导。 本文件规定的

Test methods for operating characteristics of residual current detection units for D.C.system

T/CEEIA 468-2020 直流系统用故障电弧检测模块动作特性试验方法

本文件规定了对预期用于直流系统，额定电压不超过直流1000 V，额定电流不超过63 A的故障电弧检测模块（以下简称“DC-AFDU”）进行动作特性验证试验的一般要求。 本文件规定的DC-AFDU是指： ——具有断开能力的单一装置，能在规定条件下检测到故障电弧并及时断开被保护

Test methods for operating characteristics of arc fault detection units for D.C. system

ISO 11093-8:2012 纸和纸板.纸芯的检测 第8部分:试验模型分析法测定自然频率和弯曲模量

Paper and board - Testing of cores - Part 8: Determination of natural frequency and flexural modulus by experimental modal analysis

ISO 11093-8:2017 纸和纸板.纸芯的检测.第8部分:试验模型分析法测定自然频率和弯曲模量

Paper and board - Testing of cores - Part 8: Determination of natural frequency and flexural modulus by experimental modal analysis

0 纸和纸板 纸芯的检测 第8部分:试验模型分析法测定自然频率和弯曲模量

This part of ISO 11093 specifies a method for the determination of the flexural modulus by using experimentally measured natural frequencies

ASTM E493/E493M-11(2017 在内向外测试模式下使用质谱检漏仪的泄漏标准实践

Standard Practice for Leaks Using the Mass Spectrometer Leak Detector in the Inside-Out Testing Mode

SL 130-2017 混凝土试模校验方法

IPC TM-650 5.5.1.13-1998 IPC-A-41 - 单面测试模式

This Handbook addresses the removal of solder paste and uncured/unreacted SMT adhesives from stencils, misprinted printed circuit boards (PCBs

IPC-A-41 - Single-Sided Test Pattern

IPC TM-650 5.5.1.15-1998 IPC-A-43 - 十层测试模式

This guideline document addresses the issues pertinent to temperature profiling of electronic

IPC-A-43 - Ten Layer Test Pattern

IPC TM-650 5.5.1.16-1998 IPC-A-44 - 四层测试模式

This document is intended to be a tool for a customer or supplier organization’s internal audit group to assess

IPC-A-44 - Four Layer Test Pattern

IPC TM-650 5.8.2-1973 灵活的多层测试模式

This test method is used to determine the major constituents in tin-lead plating baths. Two methods are given to determine the lead content

Flexible Multilayer Test Pattern

SL 125-2017 水泥胶砂试模校验方法

SL/T 125-2017 水泥胶砂试模校验方法

IPC TM-650 5.5.1.6-1998 IPC-A-30 - 柔性电路测试模式

This specification establishes the specific requirements for the organic mounting structure used to interconnect chip components, which

IPC-A-30 - Flexible Circuits Test Pattern

IPC TM-650 5.5.6.3-1998 标准的绝缘电阻测试模式

Reference Information

Standard Insulation Resistance Test Pattern

SNI 05-6437-2000 使用测试模型测试水泵性能的方法

Performance test methods for pumps using test models

BS PD IEC TS 63209-1:2021 光伏组件 扩展压力测试 模块

Photovoltaic modules. Extended-stress testing. Modules

IPC TM-650 5.5.1.8-1998 IPC-A-32 - 灵活的多层测试模式

This specification covers end product inspection and test of high frequency (microwave) printed boards for microstrip, stripline, mixed dielectric

IPC-A-32 - Flexible Multilayer Test Pattern

IPC TM-650 5.8.5-1973 耐化学溶剂敏感性测试模式

This method covers a rapid procedure for determining the nonvolatile content of epoxy resin solutions

Chemical Resistance Solvent Sensitivity Test Pattern

IPC TM-650 5.5.1.7-1998 IPC-A-31 -柔性材料C组测试模式

This specification establishes the specific requirements for organic high-density interconnect (HDI) layers with microvia technology and the quality

IPC-A-31 - Flexible Material Group C Test Pattern

ONORM M 8125-1994 摩擦技术．摩擦磨损测试．模型试验．系统球盘

In dieser ?NORM werden die wesentlichen Prüfbedingungen spezifiziert, die bei Reibungs- und Verschlei?prüfungen mit dem Modellversuch: System

Tribotechnique - Testing of friction and wear - Model test: System ball-on-disc