T/CAME 32-2021 医用气体汇流排
本文件规定了医用气体汇流排(以下简称“汇流排”)的分类、概述、技术要求、试验方法、检验规则、标志、使用说明书、包装、运输和贮存。 本文件适用于进气压力不大于20000kPa的汇流排的设计、生产和检验。 本文件不适用于焊接绝热气瓶江流排
Medical gas manifold
T/CCGA 20003-2021 气体汇流排安全技术要求
本文件规定了气体汇流排的技术要求、试验方法、检验规则及标志、包装、储运。 本文件适用于公称工作压力不大于25MPa，环境温度为-40℃～60℃的工业气体、燃气、高纯气体、电子气体、食药级气体、消防气体以及其他特种气体的单一气体、混合气体的充装和供应气体汇流排（以下简称“汇流排”）。集束装置上的
Safety technical requirements for gases mainfold
YY/T 1439.2-2016 医用气体压力调节器第2部分:汇流排压力调节器和管道压力调节器
*YY/T 1439的本部分规定了预期与15 ℃时最大标称灌充压力为25 000 kPa的气瓶相连接的汇流排压力调节器(在3.6中定义)和最大进气口压力为3 000 kPa、在管道系统中使用的管道压力调节器(在3.4中定义)的要求，压力调节器预期用于下列医用气体： --氧气； --氧化亚氮(笑气
Pressure regulators for use with medical gases.Part 2:Manifold and line pressure regulators
TB/T 3252-2010 电气化铁路接触网汇流排
本标准规定了电气化铁路和城市轨道接触网用汇流排、汇流排终端及其中间接头的术语和定义、分类、技术要求、试验方法、检验规则、标志、包装等。 本标准适用于电气化铁路和城市轨道接触网用汇流排、汇流排终端及其中间接头的设计、制造、试验
Overhead conductor rail for overhead contact system in electrification railway
ISO 12718:2019 损检测.涡流检测.词汇
Non-destructive testing — Eddy current testing — Vocabulary
KS B ISO 12718:2021 损检测.涡流检测.词汇
Non-destructive testing — Eddy current testing — Vocabulary
SANS 12718:2010 损检测．涡流检测．词汇表
Defines terms used in eddy current testing
Non-destructive testing - Eddy current testing - Vocabulary
ISO 15002:2000 医用气体管道系统终端装置用气流量测量装置
1 This International Standard is applicable to: — flow-metering devices which are connected, either directly or by means of flexible connecting
Flow-metering devices for connection to terminal units of medical gas pipeline systems
CJ/T 307-2009 城镇排水设施气体的检测方法
本标准规定了城镇下水道中的可燃性气体、硫化氢、氧气、氨气、一氧化碳、二氧化硫、氯气、二氧化碳和总挥发性有机物气体的实验室检测方法和(或)现场快速检测方法。 本标准适用于城镇接纳和输送城镇污水、工业废水和雨水的管网、沟渠和泵站，污水处理设施，污泥最终处置设施及其他相关设施中蓄积气体的测定
Test methods for the gas from town wastewater facilities
JJG 688-1990 汽车排放气体测试仪检定规程
Verification Regulation of Vehicle Exhaust Emission Measuring Instruments
JJG 688-2007 汽车排放气体测试仪检定规程
本规程适用于汽车排放气体测试仪（以下简称测试仪）的首次检定、后续检定和使 用中的检验，型式评价试验的相关项目可参照本规程执行
Vehicle Exhaust Emissions Measuring Instruments
ANSI/ASME MFC-1M-2003 液体流量测量用术语汇编
This standard consists of a collection of definitions of those terms which pertain to the measurement of fluid flow in pipes. Only those terms
Glossary of Terms Used in the Measurement of Fluid Flow in Pipes
JJG 688-2017 汽车排放气体测试仪检定规程
SN/T 0817-1999 出口轴流式交流排气扇检验规程
Rules for the inspection of axial-flow alternating fans for export
SN ISO 2931:1986 铝线和汇流排规则
Diese Methode erlaubt die rasche zerst?rungsfreie Messung der Qualit?t von anodisch erzeugten und ver-dichteten Oxidschichten und eignet sich deshalb
Anodizing of aluminium and its alloys — Assessment of quality of sealed anodicoxide coatings by measurement of admittance or impedance
DS 938:1987 医用气体气瓶．标志
Denne standard omfatter m?rkning af transportable behol-dere (trykflasker) til medicinsk brug. M?rkningen skal ske ved hj?lp af stempling
Gas cylinders for gases for medical use. Marking
AS 2568-1991 医用气体．医用压缩呼吸空气的纯度
Specifies the levels of purity and analysis of compressed medical breathing air supplied by a pipeline directly from an air compressor. Definitions
Medical gases - Purity of compressed medical breathing air
JUS M.E3.001-1992 民用气体安装．词汇
Domestic gas installations. Vocabulary
GOST R IEC/TR 60788-2009 医疗电气设备. 词汇表
Medical electrical equipment. Glossary
ANSI/ASME MFC-1M-2003 液体流量测量用术语汇编
This standard consists of a collection of definitions of those terms which pertain to the measurement of fluid flow in pipes. Only those terms
Glossary of Terms Used in the Measurement of Fluid Flow in Pipes
KS R ISO 16183:2009 重型机车.未处理排气的气体排放测量和瞬变试验条件下用部分流体稀释系统测量粒子排放
이 표준은 대형 엔진(heavy duty engine)을 시험대(동력계)에서 과도 시험 조
Heavy duty engines-Measurement of gaseous emissions from raw exhaust gas and of particulate emissions using partial flow dilution systems under transient test conditions
BS ISO 16183:2003 重型机车.未处理排气的气体排放测量和瞬变试验条件下用部分流体稀释系统测量粒子排放
This International Standard specifies methods for the measurement and evaluation of gaseous and particulate exhaust emissions from heavy-duty engines
Heavy duty engines - Measurement of gaseous emissions from raw exhaust gas and of particulate emissions using partial flow dilution systems under transient test conditions
ISO 16183:2002 重型机车.未处理排气的气体排放测量和瞬变试验条件下用部分流体稀释系统测量粒子排放
This International Standard specifies methods for the measurement and evaluation of gaseous and particulate exhaust emissions from heavy-duty engines
Heavy-duty engines - Measurement of gaseous emissions from raw exhaust gas and of particulate emissions using partial flow dilution systems under transient test conditions
JB/T 2294-1999 轴流式交流排气风扇
本标准适用于工业及类似环境下安装在墙壁上作排气通风之用的轴流式交流排气风扇
Axial a.c.electric ventilating fans
IRAM 2588-1962 医用气体的鉴定
B-l En esta norma se stablece la identificación o sistema de se-guridad por medio de colores de los recipientes que contienan
CKS 64-1990 医用气体的规范
This specification covers the requirements for medical air for breathing purposes
SPECIFICATION FOR MEDICAL AIR
BS EN ISO 7396-1:2016 医用气体管道系统.压缩医用气体和真空用管道系统
Medical gas pipeline systems. Pipeline systems for compressed medical gases and vacuum
BS EN ISO 7396-1:2016+A1:2019 医用气体管道系统 压缩医用气体和真空用管道系统
Medical gas pipeline systems. Pipeline systems for compressed medical gases and vacuum
BS EN ISO 7396-1:2007+A2:2010 医用气体管道系统.压缩医用气体和真空用管道系统
This part of ISO 7396 specifies requirements for design, installation, function, performance, documentation, testing and commissioning of pipeline
Medical gas pipeline systems - Pipeline systems for compressed medical gases and vacuum
BS EN ISO 7396-1:2007+A3:2013 医用气体管道系统.压缩医用气体和真空用管道系统
Medical gas pipeline systems - Pipeline systems for compressed medical gases and vacuum
编辑：北检院编辑部
