GB/T 26143-2010 液压管接头 试验方法
警告：本标准中所述的一些试验是危险的，因此在进行试验时必须严格地采取各种适合的安全预防措施。对于爆裂、细微喷射（可能会穿透皮肤）和膨胀气体的能量释放等危险应引起注意，为减小能量释放的危险，在压力试验前应排出试件内的空气。试验应由经过培训合格的人员操作和完成。 本标准规定了液压传动中使用的各类金属管
Connectors for hydraulic fluid power.Test methods
GB/T 14034-1993 24°非扩口液压管接头连接尺寸
本标准规定了以液压油（液）为工作介质的液压系统用24°非扩口液压管接头体端部的连接尺寸。 本标准适用于硬管接头和软管接头
Hydraulic fluid power.Connection for tubes and hoses.Dimensions and designs for 24 degree flareless fittings
GB/T 19674.1-2005 液压管接头用螺纹油口和柱端 螺纹油口
GB/T 19674的本部分规定了液压管接头用螺纹油口的尺寸和技术要求。其尺寸适用于GB/T 19674.2和GB/T 19674.3中的柱端。 本部分所规定的油口适用的最高工作压力为63MPa。许用工作压力应根据油口尺寸、材料、工艺、工况、用途等来确定
Connections for general use and fluid power Ports and stud ends with thread-Threaded port
SAE MA2003-1981 液压管接头和配件的旋转弯曲试验
This standard establishes flexure test procedures to determine and classify the fatigue strengths of reconnectable or permanent hydraulic tube joints.
Rotary Flexure Testing of Hydraulic Tubing Joints and Fittings
SAE J1502-2013 液压动力和一般用途的液压管接头的连接诊断
SAE J1502 specifies dimensions, performance requirements, and test procedures for the male half of a diagnostic coupler with either a metric M14x1.5
Connections for Fluid Power and General Use Hydraulic Couplings Diagnostic
SAE J1502-1997 (R)液压动力和一般用途的液压管接头的连接诊断
SAE J1502 specifies dimensions, performance requirements, and test procedures for the male half of a diagnostic coupler with either a metric M14x1.5
(R) Connections for Fluid Power and General Use - Hydraulic Couplings - Diagnostic
BS ISO 7257:2016 航空器.液压管接头和连接接头.扭转弯曲试验
Aircraft. Hydraulic tubing joints and fittings. Rotary flexure test
ISO 7257:2016 航空器 液压管接头和连接接头扭转弯曲试验
Aircraft - Hydraulic tubing joints and fittings - Rotary flexure test
ISO 7257:1983 航空器 液压管接头和连接接头扭转弯曲试验
Specifies procedures to determine and classify the fatigue strength of reconnectable or permanent hydraulic tube joints. The procedure is intended
Aircraft; Hydraulic tubing joints and fittings; Rotary flexure test
DLA MS51820 REV E NOTICE 1-1999 90度液压弯管接头
This notice should be filed in front of MS51820E, dated 30 July 1987
ELBOW, TUBE, 90 DEGREE, FLARELESS TYPE, HYDRAULIC [Refer To: SAE J514, SAE J514, SAE J514, SAE J514, SAE J514]
DLA MS51820 REV E-1987 90度液压弯管接头
Steel, corrosion-resisting i n accordance with procurement specification
ELBOW, TUBE, 90 DEGREE, FLARELESS TYPE, HYDRAULIC [Refer To: SAE J514, SAE J514, SAE J514, SAE J514, SAE J514]
SAE ARP1258B-1993 液压管接头的特殊柔性疲劳试验的质量要求
This SAE Aerospace Recommended Practice (ARP) establishes the method for qualification testing of tube joints and fitting attachments, using
Qualification of Hydraulic Tube Joints to Specified Flexure Fatigue Requirements
DS/ISO 5675:1983 农业拖拉机和机械.一般用途液压管接头.规范
Denne standard g?lder for koblinger til hydrauliske forbindelser, der ofte skal til- eller frakobles, for at landbrugsmaskiner kan skiftes fra traktor
Agricultural tractors. Hydraulic couplers for general purpose. Specifications
ISO/TS 17165-2:2013 液压机液体动力.软管接头.第2部分:液压软管接头用操作规程
Hydraulic fluid power - Hose assemblies - Part 2: Practices for hydraulic hose assemblies
ISO/TS 17165-2:2018 液压机液体动力.软管接头.第2部分:液压软管接头用操作规程
Hydraulic fluid power - Hose assemblies - Part 2: Practices for hydraulic hose assemblies
GB/T 26143-2010 液压管接头 试验方法
警告：本标准中所述的一些试验是危险的，因此在进行试验时必须严格地采取各种适合的安全预防措施。对于爆裂、细微喷射（可能会穿透皮肤）和膨胀气体的能量释放等危险应引起注意，为减小能量释放的危险，在压力试验前应排出试件内的空气。试验应由经过培训合格的人员操作和完成。 本标准规定了液压传动中使用的各类金属管
Connectors for hydraulic fluid power.Test methods
GB/T 14034-1993 24°非扩口液压管接头连接尺寸
本标准规定了以液压油（液）为工作介质的液压系统用24°非扩口液压管接头体端部的连接尺寸。 本标准适用于硬管接头和软管接头
Hydraulic fluid power.Connection for tubes and hoses.Dimensions and designs for 24 degree flareless fittings
GB/T 19674.1-2005 液压管接头用螺纹油口和柱端 螺纹油口
GB/T 19674的本部分规定了液压管接头用螺纹油口的尺寸和技术要求。其尺寸适用于GB/T 19674.2和GB/T 19674.3中的柱端。 本部分所规定的油口适用的最高工作压力为63MPa。许用工作压力应根据油口尺寸、材料、工艺、工况、用途等来确定
Connections for general use and fluid power Ports and stud ends with thread-Threaded port
SAE MA2003-1981 液压管接头和配件的旋转弯曲试验
This standard establishes flexure test procedures to determine and classify the fatigue strengths of reconnectable or permanent hydraulic tube joints.
Rotary Flexure Testing of Hydraulic Tubing Joints and Fittings
SAE J1502-2013 液压动力和一般用途的液压管接头的连接诊断
SAE J1502 specifies dimensions, performance requirements, and test procedures for the male half of a diagnostic coupler with either a metric M14x1.5
Connections for Fluid Power and General Use Hydraulic Couplings Diagnostic
SAE J1502-1997 (R)液压动力和一般用途的液压管接头的连接诊断
SAE J1502 specifies dimensions, performance requirements, and test procedures for the male half of a diagnostic coupler with either a metric M14x1.5
(R) Connections for Fluid Power and General Use - Hydraulic Couplings - Diagnostic
BS ISO 7257:2016 航空器.液压管接头和连接接头.扭转弯曲试验
Aircraft. Hydraulic tubing joints and fittings. Rotary flexure test
ISO 7257:2016 航空器 液压管接头和连接接头扭转弯曲试验
Aircraft - Hydraulic tubing joints and fittings - Rotary flexure test
ISO 7257:1983 航空器 液压管接头和连接接头扭转弯曲试验
Specifies procedures to determine and classify the fatigue strength of reconnectable or permanent hydraulic tube joints. The procedure is intended
Aircraft; Hydraulic tubing joints and fittings; Rotary flexure test
DLA MS51820 REV E NOTICE 1-1999 90度液压弯管接头
This notice should be filed in front of MS51820E, dated 30 July 1987
ELBOW, TUBE, 90 DEGREE, FLARELESS TYPE, HYDRAULIC [Refer To: SAE J514, SAE J514, SAE J514, SAE J514, SAE J514]
DLA MS51820 REV E-1987 90度液压弯管接头
Steel, corrosion-resisting i n accordance with procurement specification
ELBOW, TUBE, 90 DEGREE, FLARELESS TYPE, HYDRAULIC [Refer To: SAE J514, SAE J514, SAE J514, SAE J514, SAE J514]
SAE ARP1258B-1993 液压管接头的特殊柔性疲劳试验的质量要求
This SAE Aerospace Recommended Practice (ARP) establishes the method for qualification testing of tube joints and fitting attachments, using
Qualification of Hydraulic Tube Joints to Specified Flexure Fatigue Requirements
DS/ISO 5675:1983 农业拖拉机和机械.一般用途液压管接头.规范
Denne standard g?lder for koblinger til hydrauliske forbindelser, der ofte skal til- eller frakobles, for at landbrugsmaskiner kan skiftes fra traktor
Agricultural tractors. Hydraulic couplers for general purpose. Specifications
ISO/TS 17165-2:2013 液压机液体动力.软管接头.第2部分:液压软管接头用操作规程
Hydraulic fluid power - Hose assemblies - Part 2: Practices for hydraulic hose assemblies
ISO/TS 17165-2:2018 液压机液体动力.软管接头.第2部分:液压软管接头用操作规程
Hydraulic fluid power - Hose assemblies - Part 2: Practices for hydraulic hose assemblies
编辑：北检院编辑部
