聚乙烯电熔组件检测

GB/T 19806-2005 塑料管材和管件 聚乙烯电熔组件的挤压剥离试验

本标准规定了用挤压的方法来确定流体输送用聚乙烯管材和电熔承口或鞍形管件组件的抗剥离性能。本标准适用于管材公称外径16mm～225mm的组件

Plastics pipes and fittings Crushing decohesion test for polyethylene(PE)electrofusion assemblies

ISO 13955:1997/Amd 1:2020 塑料管材和管件 聚乙烯电熔组件的挤压剥离试验

Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies — Amendment 1

GB/T 19808-2005 塑料管材和管件 公称外径大于或等于90mm的聚乙烯电熔组件的拉伸剥离试验

本标准规定了用拉伸的方法来确定流体输送用聚乙烯管材和电熔承口组件的抗剥离性能。 本标准适用于公称外径大于或等于90mm的组件

Plastics pipes and fittings.Peel decohesion test for polyethylene(PE)electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm

0 塑料管材和管件 聚乙烯(PE)电熔焊组件的压缩分层试验

This International Standard describes a crushing test method for determining the decohesive resistance of polyethylene (PE) pipe and electrofusion

ISO 13954:1997/Amd 1:2020 塑料管材和管件公称外径大于或等于90mm的聚乙烯（PE）电熔组件的剥离试验

Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm — Amendment 1

GB/T 19807-2005 塑料管材和管件 聚乙烯管材和电熔管件 组合试件的制备

本标准规定了聚乙烯（PE）管材或插口管件与电熔管件（例如：承口管件如套筒，或鞍形管件）组合试件的制备方法。本标准规定了组合试件制备准则，包括环境温度、熔接条件、管材和管件的尺寸、管材形状等参数，并考虑了相关产品标准中对使用条件的限制

Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene(PE)pipe and an electrofusion fitting

0 塑料管材和管件 公称外径大于或等于90mm的聚乙烯(PE)电熔焊组合件的剥离分层试验

This International Standard describes a peel test method for determining the decohesive resistance of polyethylene electrofusion socket assemblies

ISO 11413:1996 塑料管材和管件 聚乙烯(PE)管和电熔配件的组装试件的制备

Specifies a method for the preparation of test pieces assembled from polyethylene pipes or spigot-ended fittings and electrofusion fittings

Plastics pipes and fittings - Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

BS ISO 11413:2009 塑料管和配件 聚乙烯（PE）管和电熔配件试样组件的制备

Plastics pipes and fittings. Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

BS ISO 11413:2008 塑料管和配件.聚乙烯(PE)管和电熔配件试样组件的制备

Plastics pipes and fittings - Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

ISO 11413:2008 塑料管和配件.聚乙烯(PE)管和电熔配件间试样组装件的制备

This International Standard specifies a method for the preparation of test pieces assembled from polyethylene (PE) pipes or spigot-ended fittings

Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

ISO 11413:2019 塑料管和配件.聚乙烯（PE）管和电熔配件之间试件组件的制备

Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

ASTM F1055-16a(2022 外径受控聚乙烯和交联聚乙烯（PEX）管道用电熔型聚乙烯配件

Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing

ASTM F1055-11 外径控制的聚乙烯和交联聚乙烯(PEX)管用电熔型聚乙烯配件的标准规范

1.1 This specification covers electrofusion polyethylene fittings for use with outside diameter-controlled polyethylene pipe, covered

Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing

ASTM F1055-98(2006 外径受控的聚乙烯管路用电熔型聚乙烯配件标准规范

1.1 This specification covers electrofusion polyethylene fittings for use with outside diameter-controlled polyethylene pipe, covered

Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and Tubing

GB/T 19806-2005 塑料管材和管件 聚乙烯电熔组件的挤压剥离试验

本标准规定了用挤压的方法来确定流体输送用聚乙烯管材和电熔承口或鞍形管件组件的抗剥离性能。本标准适用于管材公称外径16mm～225mm的组件

Plastics pipes and fittings Crushing decohesion test for polyethylene(PE)electrofusion assemblies

ISO 13955:1997/Amd 1:2020 塑料管材和管件 聚乙烯电熔组件的挤压剥离试验

Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies — Amendment 1

GB/T 19808-2005 塑料管材和管件 公称外径大于或等于90mm的聚乙烯电熔组件的拉伸剥离试验

本标准规定了用拉伸的方法来确定流体输送用聚乙烯管材和电熔承口组件的抗剥离性能。 本标准适用于公称外径大于或等于90mm的组件

Plastics pipes and fittings.Peel decohesion test for polyethylene(PE)electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm

0 塑料管材和管件 聚乙烯(PE)电熔焊组件的压缩分层试验

This International Standard describes a crushing test method for determining the decohesive resistance of polyethylene (PE) pipe and electrofusion

ISO 13954:1997/Amd 1:2020 塑料管材和管件公称外径大于或等于90mm的聚乙烯（PE）电熔组件的剥离试验

Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm — Amendment 1

GB/T 19807-2005 塑料管材和管件 聚乙烯管材和电熔管件 组合试件的制备

本标准规定了聚乙烯（PE）管材或插口管件与电熔管件（例如：承口管件如套筒，或鞍形管件）组合试件的制备方法。本标准规定了组合试件制备准则，包括环境温度、熔接条件、管材和管件的尺寸、管材形状等参数，并考虑了相关产品标准中对使用条件的限制

Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene(PE)pipe and an electrofusion fitting

0 塑料管材和管件 公称外径大于或等于90mm的聚乙烯(PE)电熔焊组合件的剥离分层试验

This International Standard describes a peel test method for determining the decohesive resistance of polyethylene electrofusion socket assemblies

ISO 11413:1996 塑料管材和管件 聚乙烯(PE)管和电熔配件的组装试件的制备

Specifies a method for the preparation of test pieces assembled from polyethylene pipes or spigot-ended fittings and electrofusion fittings

Plastics pipes and fittings - Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

BS ISO 11413:2009 塑料管和配件 聚乙烯（PE）管和电熔配件试样组件的制备

Plastics pipes and fittings. Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

BS ISO 11413:2008 塑料管和配件.聚乙烯(PE)管和电熔配件试样组件的制备

Plastics pipes and fittings - Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

ISO 11413:2008 塑料管和配件.聚乙烯(PE)管和电熔配件间试样组装件的制备

This International Standard specifies a method for the preparation of test pieces assembled from polyethylene (PE) pipes or spigot-ended fittings

Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

ISO 11413:2019 塑料管和配件.聚乙烯（PE）管和电熔配件之间试件组件的制备

Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

ASTM F1055-16a(2022 外径受控聚乙烯和交联聚乙烯（PEX）管道用电熔型聚乙烯配件

Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing

ASTM F1055-11 外径控制的聚乙烯和交联聚乙烯(PEX)管用电熔型聚乙烯配件的标准规范

1.1 This specification covers electrofusion polyethylene fittings for use with outside diameter-controlled polyethylene pipe, covered

Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing

ASTM F1055-98(2006 外径受控的聚乙烯管路用电熔型聚乙烯配件标准规范

1.1 This specification covers electrofusion polyethylene fittings for use with outside diameter-controlled polyethylene pipe, covered

Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and Tubing