带插销和插套的电器附件检测

GB/T 11919-2001 工业用插头插座和耦合器 第2部分;带插销和插套的电器附件的尺寸互换性要求

本标准适用于主要作工业用途的，户内或户外使用的额定工作电压不超过690V，额定频率500Hz，额定电流不超过125A的插头和插座、电缆耦合器和器具耦合器。 本标准适用于装有标准结构的插销和插套的插头、插座、电缆耦合器和器具耦合器。 本标准适用于在环境温度-25℃～40℃时

Plugs,socket-outlets and couplers for industrial purposes--Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories

GB/T 11918.2-2014 工业用插头插座和耦合器 第2部分:带插销和插套的电器附件的尺寸兼容性和互换性要求

GB/T 11918.1—2014的本章替换为如下:GB/T 11918的本部分规定了带插销和插套的工业用插头插座和耦合器的尺寸互换性要求等技术要求。本部分适用于主要作工业用途的,户内或户外使用的额定工作电压不超过1 000 V,额定频率500 Hz,额定电流不超过125 A的插头和插座、电缆耦合器

Plug, socket-outlets and couplers for industrial purposes.Part 2: Dimensional compatibility and interchangeability requirements for pin and contact-tube accessories

DIN EN 60309-2:2007 工业用插头、插座和耦合器.第2部分:插销和插套附件的尺寸互换性要求

Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories (IEC 60309-2:1999 + A1:2005, modified); German version EN 60309-2:1999 + A1:2007

IEC 60309-2:1999 工业用插头、插座和耦合器 第2部分:插销和插套附件的尺寸互换性要求

Replacement: This standard applies to plugs and socket-outlets, cable couplers and appliance couplers with a rated operating voltage not exceeding 690

Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories

NF C63-310/A11:2004 工业用插头、插座和耦合器.第2部分:插销和插套附件的尺寸互换性要求

Plugs, socket-outlets and couplers for industrial purposes - Part 2 : dimensional interchangeability requirements for pin and contact-tube accessories.

IEC 60309-2:1999/AMD1:2005 工业用插头、插座和耦合器.第2部分:插销和插套附件的尺寸互换性要求.修改件1

This is Amendment 1 IEC 60309-2-2005 (Plugs,socket-outlets and couplers for industrial purposes-Part2:Dimensional interchangeability requrements

Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories; Amendment 1

EN 60309-2:1998 工业用插头,插座端口和连接件.第2部分:插销和插套附件的尺寸互换性要求

Plugs@ Socket-Outlets and Couplers for Industrial Purposes Part 2: Dimensional Interchangeability Requirements for Pin and Contact-Tube Accessories

CSA C22.2 No.182.1-07-2007 销和套筒式的插栓,插座和电缆连接器.第3版

Plugs, Receptacles, and Cable Connectors of the Pin and Sleeve Type third Edition

Plugs, Receptacles, and Cable Connectors of the Pin and Sleeve Type third Edition

GB/T 24976.4-2010 电器附件环境设计导则 第4部分：工业用插头插座和耦合器

本部分规定了将环境因素引入工业用插头插座和耦合器产品的基本原则。 本部分适用于新的或改进产品的设计。 本部分适用的工业用插头插座和耦合器包括工业用插头、工业用插座和工业用连接器、工业用器具输入插座、工业用耦合器等。 本部分的目的是为了在产品的设计阶段就控制其对环境的影响

Guide of environmental design for electrical accessories.Part 4:Plugs,socket-outlets and couplers for industrial purposes

DIN 47636-5:1989 外锥套形仪器连接件用电力电缆插套组合配件.Um可达36KV.带安装法兰和螺纹销的套管.电缆插接件用带螺纹固定的套管

Bushing for separable accessories for power cable with protruding cone; U_m up to 36 kV, bushing with mounting flange and threaded inserts for the separable connector

DIN 47636-6:1989 外锥套形仪器连接件用电力电缆插套组合配件.Um可达36KV.不带安装法兰.带螺纹销的套管.电缆插接件用带螺纹固定的套管

The standard specifies the necessary dimensions for bushings with outside cones in order to ensure compatibility with separable connectors

Bushing for separable accessories for power cable with protruding cone; U_m up to 36 kV, bushing without mounting flange and threaded inserts for the separable connector

NEMA PR 3-1986 针和套筒插头 插座 和连接器指南（已撤销）

GUIDE TO PIN AND SLEEVE PLUGS@ RECEPTACLES@ AND CONNECTORS (WITHDRAWN)

EN 60309-2:1999 工业用插头,插座端口和连接件.第2部分:插销和插套附件的尺寸互换性要求;包含修改件A1-5/2004;A11-4/2007

Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories (Incorporates Amendment A2: 2012)

NF C63-310/A2*NF EN 60309-2/A2:2012 工业用插头、插座和耦合器 第2部分：插销和插套尺寸互换性的要求

Plugs, socket-outlets and couplers for industrial purposes - Part 2 : dimensional interchangeability requirements for pin and contact-tube accessories

NF C63-310/A1*NF EN 60309-2/A1:2007 工业用插头、插座和耦合器 第2部分：插销和接触管附件的尺寸互换性要求

Plugs, socket-outlets and couplers for industrial purposes - Part 2 : dimensional interchangeability requirements for pin and contact-tube accessories

GB/T 11919-2001 工业用插头插座和耦合器 第2部分;带插销和插套的电器附件的尺寸互换性要求

本标准适用于主要作工业用途的，户内或户外使用的额定工作电压不超过690V，额定频率500Hz，额定电流不超过125A的插头和插座、电缆耦合器和器具耦合器。 本标准适用于装有标准结构的插销和插套的插头、插座、电缆耦合器和器具耦合器。 本标准适用于在环境温度-25℃～40℃时

Plugs,socket-outlets and couplers for industrial purposes--Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories

GB/T 11918.2-2014 工业用插头插座和耦合器 第2部分:带插销和插套的电器附件的尺寸兼容性和互换性要求

GB/T 11918.1—2014的本章替换为如下:GB/T 11918的本部分规定了带插销和插套的工业用插头插座和耦合器的尺寸互换性要求等技术要求。本部分适用于主要作工业用途的,户内或户外使用的额定工作电压不超过1 000 V,额定频率500 Hz,额定电流不超过125 A的插头和插座、电缆耦合器

Plug, socket-outlets and couplers for industrial purposes.Part 2: Dimensional compatibility and interchangeability requirements for pin and contact-tube accessories

DIN EN 60309-2:2007 工业用插头、插座和耦合器.第2部分:插销和插套附件的尺寸互换性要求

Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories (IEC 60309-2:1999 + A1:2005, modified); German version EN 60309-2:1999 + A1:2007

IEC 60309-2:1999 工业用插头、插座和耦合器 第2部分:插销和插套附件的尺寸互换性要求

Replacement: This standard applies to plugs and socket-outlets, cable couplers and appliance couplers with a rated operating voltage not exceeding 690

Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories

NF C63-310/A11:2004 工业用插头、插座和耦合器.第2部分:插销和插套附件的尺寸互换性要求

Plugs, socket-outlets and couplers for industrial purposes - Part 2 : dimensional interchangeability requirements for pin and contact-tube accessories.

IEC 60309-2:1999/AMD1:2005 工业用插头、插座和耦合器.第2部分:插销和插套附件的尺寸互换性要求.修改件1

This is Amendment 1 IEC 60309-2-2005 (Plugs,socket-outlets and couplers for industrial purposes-Part2:Dimensional interchangeability requrements

Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories; Amendment 1

EN 60309-2:1998 工业用插头,插座端口和连接件.第2部分:插销和插套附件的尺寸互换性要求

Plugs@ Socket-Outlets and Couplers for Industrial Purposes Part 2: Dimensional Interchangeability Requirements for Pin and Contact-Tube Accessories

CSA C22.2 No.182.1-07-2007 销和套筒式的插栓,插座和电缆连接器.第3版

Plugs, Receptacles, and Cable Connectors of the Pin and Sleeve Type third Edition

Plugs, Receptacles, and Cable Connectors of the Pin and Sleeve Type third Edition

GB/T 24976.4-2010 电器附件环境设计导则 第4部分：工业用插头插座和耦合器

本部分规定了将环境因素引入工业用插头插座和耦合器产品的基本原则。 本部分适用于新的或改进产品的设计。 本部分适用的工业用插头插座和耦合器包括工业用插头、工业用插座和工业用连接器、工业用器具输入插座、工业用耦合器等。 本部分的目的是为了在产品的设计阶段就控制其对环境的影响

Guide of environmental design for electrical accessories.Part 4:Plugs,socket-outlets and couplers for industrial purposes

DIN 47636-5:1989 外锥套形仪器连接件用电力电缆插套组合配件.Um可达36KV.带安装法兰和螺纹销的套管.电缆插接件用带螺纹固定的套管

Bushing for separable accessories for power cable with protruding cone; U_m up to 36 kV, bushing with mounting flange and threaded inserts for the separable connector

DIN 47636-6:1989 外锥套形仪器连接件用电力电缆插套组合配件.Um可达36KV.不带安装法兰.带螺纹销的套管.电缆插接件用带螺纹固定的套管

The standard specifies the necessary dimensions for bushings with outside cones in order to ensure compatibility with separable connectors

Bushing for separable accessories for power cable with protruding cone; U_m up to 36 kV, bushing without mounting flange and threaded inserts for the separable connector

NEMA PR 3-1986 针和套筒插头 插座 和连接器指南（已撤销）

GUIDE TO PIN AND SLEEVE PLUGS@ RECEPTACLES@ AND CONNECTORS (WITHDRAWN)

EN 60309-2:1999 工业用插头,插座端口和连接件.第2部分:插销和插套附件的尺寸互换性要求;包含修改件A1-5/2004;A11-4/2007

Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories (Incorporates Amendment A2: 2012)

NF C63-310/A2*NF EN 60309-2/A2:2012 工业用插头、插座和耦合器 第2部分：插销和插套尺寸互换性的要求

Plugs, socket-outlets and couplers for industrial purposes - Part 2 : dimensional interchangeability requirements for pin and contact-tube accessories

NF C63-310/A1*NF EN 60309-2/A1:2007 工业用插头、插座和耦合器 第2部分：插销和接触管附件的尺寸互换性要求

Plugs, socket-outlets and couplers for industrial purposes - Part 2 : dimensional interchangeability requirements for pin and contact-tube accessories