GB/T 17650.1-1998 取自电缆或光缆的材料燃烧时释出气体的试验方法 第1部分;卤酸气体总量的测定
本标准第1部分规定的试验方法适用于取自电缆或光缆结构的以卤化聚合物为基础的混合物和含卤添加剂混合物，在燃烧时释出的除氢氟酸外的卤酸气体总量的测定。 为了保证试验的准确性，本试验方法不适用于释出卤酸量小于5mg/g的样品。 本方法不能用来确定混合物或材料为“卤”。对于此类混合物或
Test on gases evolved during combustion of materials from cables. Part 1: Determination of the amount of halogen acid gas
GB/T 17650.1-2021 取自电缆或光缆的材料燃烧时释出气体的试验方法 第1部分：卤酸气体总量的测定
本文件规定了测量取自电缆或光缆结构的以卤化聚合物为基础的混合物和含卤添加剂混合物,在燃烧时释出的除氢氟酸外的卤酸气体总量的装置和程序。 注1:本试验方法不能用于测定氟含量,氟含量的试验方法见IEC60684 2
Test on gases evolved during combustion of materials from cables or optical fiber cables—Part 1：Determination of the halogen acid gas content
GB/T 17650.2-2021 取自电缆或光缆的材料燃烧时释出气体的试验方法 第2部分：酸度（用pH测量）和电导率的测定
本文件规定了通过测量电缆或光缆各组件上的材料在燃烧过程中释出气体溶解在水溶液中的酸度(pH)和电导率,来测定其潜在的腐蚀性的装置和程序。 本文件规定的方法适用于检测电缆或光缆的各个组件。给出了计算电缆或光缆中材料组合的加权值的公式。本方法能验证电缆或光缆标准中规定的电缆或光缆结构中各组件的相关要求
Test on gases evolved during combustion of materials from cables or optical fiber cables—Part 2: Determination of acidity (by pH measurement) and conductivity
GB/T 17650.2-1998 取自电缆或光缆的材料燃烧时释出气体的试验方法 第2部分;用测量pH值和电导率来测定气体的酸度
本标准第2部分规定了取自电缆或光缆各组件上的材料在燃烧时释出气体的酸度的测量方法。 注 1有关电缆或光缆标准应说明要做试验的电缆或光缆的组成和发生争议时应采用的计算方法（见第8章）。 2本标准中术语“电缆”是指传输能量和信号的所有绝缘金属导体电缆
Test on gases evolved during combustion of materials from cables. Part 2: Determination of degree of acidity of gases by measuring pH and conductivity
ASTM D5424-10 电缆或光缆的绝缘材料在立式电缆槽结构中燃烧时的烟昏暗度的标准试验方法
This test method provides a means to measure a variety of fire-test-response characteristics associated with smoke obscuration and resulting from
Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D5424-99 电缆或光缆的绝缘材料在立式电缆槽结构中燃烧时烟雾造成黯淡的标准试验方法
1.1 This is a fire-test-response standard.
1.2 This test method provides a means to measure the smoke obscuration resulting from burning
Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D5424-23 在垂直电缆桥架配置中燃烧时包含在电缆或光纤电缆中的绝缘材料的烟雾遮蔽的标准测试方法
1.1 This is a fire-test-response standard. 1.2 This test method provides a means to measure the smoke obscuration resulting from burning electrical
Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D5537-99 电缆或光缆的绝缘材料在立式电缆槽结构中燃烧时热释放,火焰扩散和质量损失试验的标准试验方法
1.1 This is a fire-test-response standard.
1.2 This test method provides a means to measure the heat released by burning the electrical
Standard Test Method for Heat Release, Flame Spread and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D5537-08 电缆或光缆的绝缘材料在立式电缆槽结构中燃烧时热释放,火焰扩散和质量损失试验的标准试验方法
This test method provides a means to measure a variety of fire-test-response characteristics associated with heat and smoke release and resulting
Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D5537-10 电缆或光缆的绝缘材料在立式电缆槽结构中燃烧时的热释放、展焰性、烟昏暗度和质量损失试验的标准试验方法
This test method provides a means to measure a variety of fire-test-response characteristics associated with heat and smoke release and resulting
Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D5537-23 在垂直电缆桥架配置中燃烧时包含在电缆或光纤电缆中的绝缘材料的热释放、火焰传播、烟雾遮蔽和质量损失测试的标准测试方法
1.1 This is a fire-test-response standard. 1.2 This test method provides a means to measure the heat released and smoke obscuration by burning
Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D6113-99 使用锥形量热计对包含在电缆或光缆中的绝缘材料的燃烧试验反应特性测定的标准试验方法
1.1 this is a fire-test-response standard.
Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
ASTM D6113-09 使用锥形量热计对包含在电缆或光缆中的绝缘材料的燃烧试验反应特性测定的标准试验方法
This test method is used to determine the heat release rate and a number of other fire-test-response characteristics as a result of exposing
Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
ASTM D6113-21 使用锥形量热计对包含在电缆或光缆中的绝缘材料的燃烧试验反应特性测定的标准试验方法
1.1?This is a fire-test-response standard. 1.2?Several fire-test-response characteristics, including the time to sustained flaming, heat release rate
Standard Test Method for Using Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
ASTM D6113-03 用锥形量热计对电缆或光缆中绝缘材料的着火试验反应特性测定的标准试验方法
This test method is used to determine the heat release rate and a number of other fire-test-response characteristics as a result
Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
GB/T 17650.1-1998 取自电缆或光缆的材料燃烧时释出气体的试验方法 第1部分;卤酸气体总量的测定
本标准第1部分规定的试验方法适用于取自电缆或光缆结构的以卤化聚合物为基础的混合物和含卤添加剂混合物，在燃烧时释出的除氢氟酸外的卤酸气体总量的测定。 为了保证试验的准确性，本试验方法不适用于释出卤酸量小于5mg/g的样品。 本方法不能用来确定混合物或材料为“卤”。对于此类混合物或
Test on gases evolved during combustion of materials from cables. Part 1: Determination of the amount of halogen acid gas
GB/T 17650.1-2021 取自电缆或光缆的材料燃烧时释出气体的试验方法 第1部分：卤酸气体总量的测定
本文件规定了测量取自电缆或光缆结构的以卤化聚合物为基础的混合物和含卤添加剂混合物,在燃烧时释出的除氢氟酸外的卤酸气体总量的装置和程序。 注1:本试验方法不能用于测定氟含量,氟含量的试验方法见IEC60684 2
Test on gases evolved during combustion of materials from cables or optical fiber cables—Part 1：Determination of the halogen acid gas content
GB/T 17650.2-2021 取自电缆或光缆的材料燃烧时释出气体的试验方法 第2部分：酸度（用pH测量）和电导率的测定
本文件规定了通过测量电缆或光缆各组件上的材料在燃烧过程中释出气体溶解在水溶液中的酸度(pH)和电导率,来测定其潜在的腐蚀性的装置和程序。 本文件规定的方法适用于检测电缆或光缆的各个组件。给出了计算电缆或光缆中材料组合的加权值的公式。本方法能验证电缆或光缆标准中规定的电缆或光缆结构中各组件的相关要求
Test on gases evolved during combustion of materials from cables or optical fiber cables—Part 2: Determination of acidity (by pH measurement) and conductivity
GB/T 17650.2-1998 取自电缆或光缆的材料燃烧时释出气体的试验方法 第2部分;用测量pH值和电导率来测定气体的酸度
本标准第2部分规定了取自电缆或光缆各组件上的材料在燃烧时释出气体的酸度的测量方法。 注 1有关电缆或光缆标准应说明要做试验的电缆或光缆的组成和发生争议时应采用的计算方法（见第8章）。 2本标准中术语“电缆”是指传输能量和信号的所有绝缘金属导体电缆
Test on gases evolved during combustion of materials from cables. Part 2: Determination of degree of acidity of gases by measuring pH and conductivity
ASTM D5424-10 电缆或光缆的绝缘材料在立式电缆槽结构中燃烧时的烟昏暗度的标准试验方法
This test method provides a means to measure a variety of fire-test-response characteristics associated with smoke obscuration and resulting from
Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D5424-99 电缆或光缆的绝缘材料在立式电缆槽结构中燃烧时烟雾造成黯淡的标准试验方法
1.1 This is a fire-test-response standard.
1.2 This test method provides a means to measure the smoke obscuration resulting from burning
Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D5424-23 在垂直电缆桥架配置中燃烧时包含在电缆或光纤电缆中的绝缘材料的烟雾遮蔽的标准测试方法
1.1 This is a fire-test-response standard. 1.2 This test method provides a means to measure the smoke obscuration resulting from burning electrical
Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D5537-99 电缆或光缆的绝缘材料在立式电缆槽结构中燃烧时热释放,火焰扩散和质量损失试验的标准试验方法
1.1 This is a fire-test-response standard.
1.2 This test method provides a means to measure the heat released by burning the electrical
Standard Test Method for Heat Release, Flame Spread and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D5537-08 电缆或光缆的绝缘材料在立式电缆槽结构中燃烧时热释放,火焰扩散和质量损失试验的标准试验方法
This test method provides a means to measure a variety of fire-test-response characteristics associated with heat and smoke release and resulting
Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D5537-10 电缆或光缆的绝缘材料在立式电缆槽结构中燃烧时的热释放、展焰性、烟昏暗度和质量损失试验的标准试验方法
This test method provides a means to measure a variety of fire-test-response characteristics associated with heat and smoke release and resulting
Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D5537-23 在垂直电缆桥架配置中燃烧时包含在电缆或光纤电缆中的绝缘材料的热释放、火焰传播、烟雾遮蔽和质量损失测试的标准测试方法
1.1 This is a fire-test-response standard. 1.2 This test method provides a means to measure the heat released and smoke obscuration by burning
Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ASTM D6113-99 使用锥形量热计对包含在电缆或光缆中的绝缘材料的燃烧试验反应特性测定的标准试验方法
1.1 this is a fire-test-response standard.
Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
ASTM D6113-09 使用锥形量热计对包含在电缆或光缆中的绝缘材料的燃烧试验反应特性测定的标准试验方法
This test method is used to determine the heat release rate and a number of other fire-test-response characteristics as a result of exposing
Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
ASTM D6113-21 使用锥形量热计对包含在电缆或光缆中的绝缘材料的燃烧试验反应特性测定的标准试验方法
1.1?This is a fire-test-response standard. 1.2?Several fire-test-response characteristics, including the time to sustained flaming, heat release rate
Standard Test Method for Using Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
ASTM D6113-03 用锥形量热计对电缆或光缆中绝缘材料的着火试验反应特性测定的标准试验方法
This test method is used to determine the heat release rate and a number of other fire-test-response characteristics as a result
Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
编辑：北检院编辑部
