ISO 13953:2001 聚乙烯管材和管件 拉申强度的测定和熔接对接接头试件的失效模型
This International Standard describes a test method for determination of the tensile strength and tensile failure mode of butt-fused polyethylene (PE
Polyethylene(PE) pipes and fittings - Determination of the tensile strengt and failure mode of test pieces from a butt-fused joint
SAE AS2094A-2011 管接头组件试验方法
This SAE Aerospace Standard (AS) specifies test methods for tube-fitting assemblies used in aircraft fluid systems in the following pressure classes
Test Methods for Tube-Fitting Assemblies
SAE AS2094B-2018 管接头组件试验方法
This SAE Aerospace Standard (AS) specifies test methods for tube-fitting assemblies used in aircraft fluid systems in the following pressure classes
Test Methods for Tube-Fitting Assemblies
SIS SS 11 21 72-1980 对接焊接接头．拉伸试件．类型HS
Butt welded joints — Tensile test pieces type HS
SIS SS 11 21 73-1980 对接焊接接头．拉伸试件类型JS
Butt welded joints — Tensile test pieces type JS
SIS SS 11 21 71-1980 对接焊接接头．拉伸试件类型FS
Butt welded joints — Tensile test pieces type FS
SAE AS2094-2007 管接头组件的测试方法
This SAE Aerospace Standard (AS) specifies test methods for fitting assemblies used in aircraft fluid systems in the pressure classes B, D, and E
Test Methods for Tube-Fitting Assemblies
SAE MA2094-2015 管接头组件的测试方法，公制（ISO 10583）
This SAE Aerospace Standard (AS) specifies test methods for fitting assemblies used in aircraft fluid systems in the pressure classes B, D, and E
Test Methods for Tube-Fitting Assemblies, Metric (ISO 10583)
QJ 1445-1988 液压导管接头和连接件回转弯曲试验方法
Rotary bend test method for hydraulic conduit fittings and fittings
SAE ARP1185B-1993 液压管路接头和配件挠曲试验
This SAE Recommended Practice (ARP) establishes flexure test procedures to determine and classify the fatigue strengths of reconnectable or permanent
Flexure Testing of Hydraulic Tubing Joints and Fittings
DIN ISO 10583:1998 航空航天流体系统.管/管接头组件的试验方法
The test methods specified apply to fitting assemblies used in aircraft fluid systems in the pressure and temperature ranges covered by pressure
Aerospace fluid systems - Test methods for tube/fitting assemblies (ISO 10583:1993)
BS 2782-11 Method 1150E:1997 塑料试验方法.第11部分:热塑性塑料管,接头和阀门.试验方法1150E:塑料管和配件.聚乙烯管和电熔融接头间试件制备
This International Standard specifies a method for the preparation of test pieces assembled from poly-ethylene (PE) pipes or spigot-ended fittings
Methods of testing plastics - Thermoplastics pipes, fittings and valves - Plastics pipes and fittings - Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
ANSI/IEEE Std 383-1974 核电站用 1E 类电缆、现场接头和连接件型式试验的 IEEE 标准
Directions for establishing type tests that may be used in qualifying Class 1E electric cables, field splices, and other connections for service
IEEE Standard for Type Test of Class 1E Electric Cables, Field Splices, and Connections for Nuclear Power Generating Stations
NF S76-013:1989 呼吸保护装置.管接头组件.要求、试验、标志
Respiratory protective devices. Mouthpiece assemblies. Requirements, testing, marking.
HB 6133-1987 液压软管、导管、接头组件的脉冲试验
本标准规定了对工作压力为28MPa及28MPa以下的液压系统中使用的软管、导管、接头组件进行液压脉冲试验的要求和方法
Impulse testing of hydraulic hose, conduit, fitting assemblies
ISO 13953:2001 聚乙烯管材和管件 拉申强度的测定和熔接对接接头试件的失效模型
This International Standard describes a test method for determination of the tensile strength and tensile failure mode of butt-fused polyethylene (PE
Polyethylene(PE) pipes and fittings - Determination of the tensile strengt and failure mode of test pieces from a butt-fused joint
SAE AS2094A-2011 管接头组件试验方法
This SAE Aerospace Standard (AS) specifies test methods for tube-fitting assemblies used in aircraft fluid systems in the following pressure classes
Test Methods for Tube-Fitting Assemblies
SAE AS2094B-2018 管接头组件试验方法
This SAE Aerospace Standard (AS) specifies test methods for tube-fitting assemblies used in aircraft fluid systems in the following pressure classes
Test Methods for Tube-Fitting Assemblies
SIS SS 11 21 72-1980 对接焊接接头．拉伸试件．类型HS
Butt welded joints — Tensile test pieces type HS
SIS SS 11 21 73-1980 对接焊接接头．拉伸试件类型JS
Butt welded joints — Tensile test pieces type JS
SIS SS 11 21 71-1980 对接焊接接头．拉伸试件类型FS
Butt welded joints — Tensile test pieces type FS
SAE AS2094-2007 管接头组件的测试方法
This SAE Aerospace Standard (AS) specifies test methods for fitting assemblies used in aircraft fluid systems in the pressure classes B, D, and E
Test Methods for Tube-Fitting Assemblies
SAE MA2094-2015 管接头组件的测试方法，公制（ISO 10583）
This SAE Aerospace Standard (AS) specifies test methods for fitting assemblies used in aircraft fluid systems in the pressure classes B, D, and E
Test Methods for Tube-Fitting Assemblies, Metric (ISO 10583)
QJ 1445-1988 液压导管接头和连接件回转弯曲试验方法
Rotary bend test method for hydraulic conduit fittings and fittings
SAE ARP1185B-1993 液压管路接头和配件挠曲试验
This SAE Recommended Practice (ARP) establishes flexure test procedures to determine and classify the fatigue strengths of reconnectable or permanent
Flexure Testing of Hydraulic Tubing Joints and Fittings
DIN ISO 10583:1998 航空航天流体系统.管/管接头组件的试验方法
The test methods specified apply to fitting assemblies used in aircraft fluid systems in the pressure and temperature ranges covered by pressure
Aerospace fluid systems - Test methods for tube/fitting assemblies (ISO 10583:1993)
BS 2782-11 Method 1150E:1997 塑料试验方法.第11部分:热塑性塑料管,接头和阀门.试验方法1150E:塑料管和配件.聚乙烯管和电熔融接头间试件制备
This International Standard specifies a method for the preparation of test pieces assembled from poly-ethylene (PE) pipes or spigot-ended fittings
Methods of testing plastics - Thermoplastics pipes, fittings and valves - Plastics pipes and fittings - Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
ANSI/IEEE Std 383-1974 核电站用 1E 类电缆、现场接头和连接件型式试验的 IEEE 标准
Directions for establishing type tests that may be used in qualifying Class 1E electric cables, field splices, and other connections for service
IEEE Standard for Type Test of Class 1E Electric Cables, Field Splices, and Connections for Nuclear Power Generating Stations
NF S76-013:1989 呼吸保护装置.管接头组件.要求、试验、标志
Respiratory protective devices. Mouthpiece assemblies. Requirements, testing, marking.
HB 6133-1987 液压软管、导管、接头组件的脉冲试验
本标准规定了对工作压力为28MPa及28MPa以下的液压系统中使用的软管、导管、接头组件进行液压脉冲试验的要求和方法
Impulse testing of hydraulic hose, conduit, fitting assemblies
编辑：北检院编辑部
