带表卡规检测

JB/T 10017-1999 带表卡规

本标准规定了带表卡规的型式、基本参数与尺寸、技术要求、标志与包装等。 本标准适用于分度值为 0.01mm，测量范围由 10～100mm 的带表内卡规和分度值为 0.01mm、0.02mm、0.05mm、0.10mm，测量范围至 100mm 带表外卡规

Dial snap gauge

JB/T 10017-2012 带表卡规

本标准规定了带表卡规的术语和定义、型式与基本参数、要求、试验方法、检查条件、检查方法、标志与包装等。 本标准适用于测量范围上限不大于400mm，分度值为0.005mm、0.01mm、0.02mm、0.05mm、0.1mm的指针式带表卡和分辨力为0.005mm、0.01mm、0.02mm的数显带表

Caliper gauges

JJF 1253-2010 带表卡规校准规范

本规范适用于分度值/分辨力为0.005 mm, 0.01 mm, 0.02 mm, 0.05 mm, 0.1 mm, 量程为(5-100) mm 带表卡规的校准

Calibration Specification for Dial Snap Gauges

HB 7328-1996 过盈螺纹带表梳形卡规 d=3～45

Interference thread with table comb calipers d=3~45

HB 2414-1977 HB 243-70 螺纹带表梳形卡规 d=3～30mm

HB 243-70 threaded comb gauge d=3~30mm

HB 7330-1996 过盈螺纹带表梳形卡规用对表件 d=3～6

The pair of watch parts d=3~6 for the comb-shaped caliper with watch gauge with interference thread

HB 7329-1996 过盈螺纹带表梳形卡规量头 d=3～45

Measuring head of comb-shaped caliper with interference thread band table d=3~45

HB 2422-1977 ＨＢ ２４３－７０ 螺纹带表梳形卡规及对表件技术条件

HB 243-70 Threaded Comb Calipers with Gauge and Specifications for Gauge Fittings

HB 7331-1996 过盈螺纹带表梳形卡规用对表件 d=8～30

The pair of watch parts d=8~30 for comb-shaped caliper with watch gauge with interference thread

HB 7332-1996 过盈螺纹带表梳形卡规用对表件 d=33～45

The pair of gauges for the comb-shaped caliper with interference thread band gauge d=33~45

HB 7333-1996 过盈螺纹带表梳形卡规磨损用对表件 d=3～6

Interference thread belt table comb-shaped caliper wear pair table d=3~6

HB 7334-1996 过盈螺纹带表梳形卡规磨损用对表件 d=8～30

Interference thread belt table comb-shaped caliper wear pair table d=8~30

HB 2417-1977 HB 243-70 螺纹带表梳形卡规对表件 d=3～6mm

HB 243-70 threaded comb-shaped caliper with table d=3~6mm

HB 2418-1977 HB 243-70 螺纹带表梳形卡规用对表件 d=7～30mm

HB 243-70 Comb-shaped caliper with threaded table d=7~30mm

HB 7335-1996 过盈螺纹带表梳形卡规磨损用对表件 d=33～45

Interference thread belt table comb-shaped caliper wear pair table d=33~45

JB/T 10017-1999 带表卡规

本标准规定了带表卡规的型式、基本参数与尺寸、技术要求、标志与包装等。 本标准适用于分度值为 0.01mm，测量范围由 10～100mm 的带表内卡规和分度值为 0.01mm、0.02mm、0.05mm、0.10mm，测量范围至 100mm 带表外卡规

Dial snap gauge

JB/T 10017-2012 带表卡规

本标准规定了带表卡规的术语和定义、型式与基本参数、要求、试验方法、检查条件、检查方法、标志与包装等。 本标准适用于测量范围上限不大于400mm，分度值为0.005mm、0.01mm、0.02mm、0.05mm、0.1mm的指针式带表卡和分辨力为0.005mm、0.01mm、0.02mm的数显带表

Caliper gauges

JJF 1253-2010 带表卡规校准规范

本规范适用于分度值/分辨力为0.005 mm, 0.01 mm, 0.02 mm, 0.05 mm, 0.1 mm, 量程为(5-100) mm 带表卡规的校准

Calibration Specification for Dial Snap Gauges

HB 7328-1996 过盈螺纹带表梳形卡规 d=3～45

Interference thread with table comb calipers d=3~45

HB 2414-1977 HB 243-70 螺纹带表梳形卡规 d=3～30mm

HB 243-70 threaded comb gauge d=3~30mm

HB 7330-1996 过盈螺纹带表梳形卡规用对表件 d=3～6

The pair of watch parts d=3~6 for the comb-shaped caliper with watch gauge with interference thread

HB 7329-1996 过盈螺纹带表梳形卡规量头 d=3～45

Measuring head of comb-shaped caliper with interference thread band table d=3~45

HB 2422-1977 ＨＢ ２４３－７０ 螺纹带表梳形卡规及对表件技术条件

HB 243-70 Threaded Comb Calipers with Gauge and Specifications for Gauge Fittings

HB 7331-1996 过盈螺纹带表梳形卡规用对表件 d=8～30

The pair of watch parts d=8~30 for comb-shaped caliper with watch gauge with interference thread

HB 7332-1996 过盈螺纹带表梳形卡规用对表件 d=33～45

The pair of gauges for the comb-shaped caliper with interference thread band gauge d=33~45

HB 7333-1996 过盈螺纹带表梳形卡规磨损用对表件 d=3～6

Interference thread belt table comb-shaped caliper wear pair table d=3~6

HB 7334-1996 过盈螺纹带表梳形卡规磨损用对表件 d=8～30

Interference thread belt table comb-shaped caliper wear pair table d=8~30

HB 2417-1977 HB 243-70 螺纹带表梳形卡规对表件 d=3～6mm

HB 243-70 threaded comb-shaped caliper with table d=3~6mm

HB 2418-1977 HB 243-70 螺纹带表梳形卡规用对表件 d=7～30mm

HB 243-70 Comb-shaped caliper with threaded table d=7~30mm

HB 7335-1996 过盈螺纹带表梳形卡规磨损用对表件 d=33～45

Interference thread belt table comb-shaped caliper wear pair table d=33~45