GM GMP.ASA+PC.002-1991 ASA + PC 通用
ASA + PC - General Purpose
GM GMP.ABS+PC.017-1995 ABS + PC 紫外线稳定
ABS + PC - UV Light Stabilized
GM GMP.PC+PBTP.008-1995 PC + PBTP 冲击改性，合金
PC + PBTP - Impact Modified, Alloy
GM GMP.ASA+PC.001-1993 ASA + PC 耐候性，注塑级
ASA + PC - Weather Resistant, Injection Molding Grade
GM GMP.ASA+PC.004-1993 ASA + PC 外部耐候黑色
ASA + PC - Exterior Weatherable Black
GM GMP.ABS+PC.006-1990 ABS + PC 10% 玻璃填充，混合
ABS + PC - 10% Glass Filled, Blend
GM GMP.PC+ S/MA.003-1991 PC + S/MA 中等耐热
PC + S/MA - Medium Heat Resistant
GM GMP.AES+PC.001-1990 AES + PC 耐候性，黑色，注塑级
AES + PC - Weather Resistant, Black, Injection Molding Grade
GM GMP.ABS+PC.007-1990 ABS + PC 15% 玻璃填充混合物
ABS + PC - 15% Glass Filled Blend
GMP.PC+PBT.006-2002 PC加PBT10%一耐热耐寒EPDM改良GFR
Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion
PC + PBT, 11 % - GFR, EPDM Modified, Weatherable
GM GMP.ABS+PC.012-1992 ABS + PC 高冲击、热稳定、电镀级
ABS + PC - High Impact, Heat Stabilized, Plating Grade
GMP.PC+PBTP.002-1995 PC加PBTP.混合体冲击性改良.勿用于新图.预删除.被取代 PC+PBTP.008.[被取代:GMNA GMP.PC+PBTP.008,GMNA GMP.PC+PBTP.008]
submitted to this specification shall resist soiling and permit ready cleaning by normal cleaning agents without adverse changes. 6.4 Bestandigkeit
PC + PBTP Impact Modified, Alloy
GM GMP.PC+PBTP.002-2012 PC+PBTP 冲击改性，合金（第 3 期；不用于新程序；更换）
PC+PBTP Impact Modified, Alloy (Issue 3; Do Not Use on New Programs; No Replacement)
GM GMP.PC+PETP.007-2014 PC+PETP 20% 玻璃填充（第 2 期；不要用于新程序；更换）
PC+PETP - 20% Glass Filled (Issue 2; Do Not Use on New Programs; No Replacement)
GM GMP.PC+PBTP.001-2014 PC+PBTP 抗冲击、耐候、合金（第 2 期；不用于新项目；更换）
PC+PBTP - Impact Modified, Weatherable, Alloy (Issue 2; Do Not Use on New Programs; No Replacement)
GM GMP.ASA+PC.002-1991 ASA + PC 通用
ASA + PC - General Purpose
GM GMP.ABS+PC.017-1995 ABS + PC 紫外线稳定
ABS + PC - UV Light Stabilized
GM GMP.PC+PBTP.008-1995 PC + PBTP 冲击改性，合金
PC + PBTP - Impact Modified, Alloy
GM GMP.ASA+PC.001-1993 ASA + PC 耐候性，注塑级
ASA + PC - Weather Resistant, Injection Molding Grade
GM GMP.ASA+PC.004-1993 ASA + PC 外部耐候黑色
ASA + PC - Exterior Weatherable Black
GM GMP.ABS+PC.006-1990 ABS + PC 10% 玻璃填充，混合
ABS + PC - 10% Glass Filled, Blend
GM GMP.PC+ S/MA.003-1991 PC + S/MA 中等耐热
PC + S/MA - Medium Heat Resistant
GM GMP.AES+PC.001-1990 AES + PC 耐候性，黑色，注塑级
AES + PC - Weather Resistant, Black, Injection Molding Grade
GM GMP.ABS+PC.007-1990 ABS + PC 15% 玻璃填充混合物
ABS + PC - 15% Glass Filled Blend
GMP.PC+PBT.006-2002 PC加PBT10%一耐热耐寒EPDM改良GFR
Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion
PC + PBT, 11 % - GFR, EPDM Modified, Weatherable
GM GMP.ABS+PC.012-1992 ABS + PC 高冲击、热稳定、电镀级
ABS + PC - High Impact, Heat Stabilized, Plating Grade
GMP.PC+PBTP.002-1995 PC加PBTP.混合体冲击性改良.勿用于新图.预删除.被取代 PC+PBTP.008.[被取代:GMNA GMP.PC+PBTP.008,GMNA GMP.PC+PBTP.008]
submitted to this specification shall resist soiling and permit ready cleaning by normal cleaning agents without adverse changes. 6.4 Bestandigkeit
PC + PBTP Impact Modified, Alloy
GM GMP.PC+PBTP.002-2012 PC+PBTP 冲击改性，合金（第 3 期；不用于新程序；更换）
PC+PBTP Impact Modified, Alloy (Issue 3; Do Not Use on New Programs; No Replacement)
GM GMP.PC+PETP.007-2014 PC+PETP 20% 玻璃填充（第 2 期；不要用于新程序；更换）
PC+PETP - 20% Glass Filled (Issue 2; Do Not Use on New Programs; No Replacement)
GM GMP.PC+PBTP.001-2014 PC+PBTP 抗冲击、耐候、合金（第 2 期；不用于新项目；更换）
PC+PBTP - Impact Modified, Weatherable, Alloy (Issue 2; Do Not Use on New Programs; No Replacement)
编辑：北检院编辑部
