GB/T 4266-2004 锪钻用可换导柱
本标准规定了用于莫氏锥柄平底锪钻和90°锥面锪钻的可换导柱的尺寸和技术要求。这种导柱同样能用于其他类型的刀具。图只是一种图解，不作为设计祥图
Detachable pilots for use with counterbores and countersinks
GB/T 4266-1984 锪钻用可换导柱
本标准适用于带可换导柱锥柄平底锪钻和带可换导柱锥柄90°锥面锪钻用的可换导柱，这种导柱也可用于其它型式的刀具
Detachable pilots for use with counterbores and countersinks
ISO 4208:1977 平底锪钻和90°锪钻用可换导柱 尺寸
Specifies the dimensions of these pilots for use with counterbores and 90 countersinks with Morse taper shanks in the table. They can also be used
Detachable pilots for use with counterbores and 90 degrees countersinks; Dimensions
JB/T 6358-1992 带可换导柱可转位平底锪钻
本标准规定了带可换导柱可转位平底锪钻的型式尺寸、技术要求、性能试验和标志包装的基本要求。 本标准适用于加TGB 152.3与GB 152未被代替部分中"中等装配"所规定的M6以上六角螺栓、带垫圈的六角螺母、各种圆柱头螺钉沉头座的锪钻
Indexable Flat Bottom Countersink Drill with Interchangeable Guide Pillar
JB/T 6358-2006 带可换导柱可转位平底锪钻
本标准规定了带可换导柱可转位平底锪钻的型式和尺寸、技术要求和标志包装的基本要求。带可换导柱可转位平底锪钻有削平型直柄、莫氏锥柄、圆柱销快换柄三种型式。 本标准适用于加工GB/T 152 、GB/T 152.3、GB/T152.4所规定的M6以上六角螺栓、带垫圈的六角螺母、各种圆柱头
Counterbores with indexable inserts and detachable pilots
GB/T 4261-1984 带可换导柱锥柄平底锪钻
本标准适用于加工GB152-76《紧固件通孔及沉头座尺寸》标准中所规定的六角头螺栓、带垫圈的六角螺母、圆柱头螺钉（包括内六角螺钉和内花键螺钉）沉头座的带导柱锥柄平底锪钻
Counterbores with morse taper shanks and detachable pilots
GB/T 4264-1984 带可换导柱锥柄90°锥面锪钻
本标准适用于加工GB152-76《紧固件通孔及沉头座尺寸》标准中所规定的沉头螺钉沉头座的带导柱锥柄90°锥面锪钻
90 degree countersinks with morse taper shanks and detachable pilots
GB/T 4261-2004 带可换导柱的莫氏锥柄平底锪钻
本标准规定了带可换导柱的莫氏锥柄平底锪钻的尺寸和公差
Counterbores with Morse taper shanks and detachable pilots
ISO 4204:2016 可换导柱式莫氏锥度柄90°锪钻
Countersinks, 90°, with Morse taper shanks and detachable pilots
ISO 4204:1977 可换导柱式莫氏锥度柄90°锪钻
This International Standard specifies the dimensions of 90°countersinks with Morse taper shanks and detachable pilots for general use
Countersinks, 90 degrees, with Morse taper shanks and detachable pilots
ISO 4207:1977 可换导柱式莫氏锥柄平底锪钻
This International Standard specifies the dimensions of counterbores with Morse taper shanks and detachable pilots for general use. The illustration
Counterbores with Morse taper shanks and detachable pilots
ISO 4207:2016 可换导柱式莫氏锥柄平底锪钻
This International Standard specifies the dimensions of counterbores with Morse taper shanks and detachable pilots for general use. NOTE Figure 1
Counterbores with Morse taper shanks and detachable pilots
GB/T 4264-2004 带可换导柱的莫氏锥柄90°锥面锪钻
本标准规定了带可换导柱的莫氏锥柄90°锥面锪钻的尺寸和公差
Countersinks,90°,with Morse taper shanks and detachable pilots
GB/T 4261-2004 带可换导柱的莫氏锥柄平底锪钻
Morse taper shank countersink drill with replaceable guide post
BS ISO 4204:2016 带可换导柱的莫氏锥柄90°锥面锪钻
Countersinks, 90
GB/T 4266-2004 锪钻用可换导柱
本标准规定了用于莫氏锥柄平底锪钻和90°锥面锪钻的可换导柱的尺寸和技术要求。这种导柱同样能用于其他类型的刀具。图只是一种图解，不作为设计祥图
Detachable pilots for use with counterbores and countersinks
GB/T 4266-1984 锪钻用可换导柱
本标准适用于带可换导柱锥柄平底锪钻和带可换导柱锥柄90°锥面锪钻用的可换导柱，这种导柱也可用于其它型式的刀具
Detachable pilots for use with counterbores and countersinks
ISO 4208:1977 平底锪钻和90°锪钻用可换导柱 尺寸
Specifies the dimensions of these pilots for use with counterbores and 90 countersinks with Morse taper shanks in the table. They can also be used
Detachable pilots for use with counterbores and 90 degrees countersinks; Dimensions
JB/T 6358-1992 带可换导柱可转位平底锪钻
本标准规定了带可换导柱可转位平底锪钻的型式尺寸、技术要求、性能试验和标志包装的基本要求。 本标准适用于加TGB 152.3与GB 152未被代替部分中"中等装配"所规定的M6以上六角螺栓、带垫圈的六角螺母、各种圆柱头螺钉沉头座的锪钻
Indexable Flat Bottom Countersink Drill with Interchangeable Guide Pillar
JB/T 6358-2006 带可换导柱可转位平底锪钻
本标准规定了带可换导柱可转位平底锪钻的型式和尺寸、技术要求和标志包装的基本要求。带可换导柱可转位平底锪钻有削平型直柄、莫氏锥柄、圆柱销快换柄三种型式。 本标准适用于加工GB/T 152 、GB/T 152.3、GB/T152.4所规定的M6以上六角螺栓、带垫圈的六角螺母、各种圆柱头
Counterbores with indexable inserts and detachable pilots
GB/T 4261-1984 带可换导柱锥柄平底锪钻
本标准适用于加工GB152-76《紧固件通孔及沉头座尺寸》标准中所规定的六角头螺栓、带垫圈的六角螺母、圆柱头螺钉（包括内六角螺钉和内花键螺钉）沉头座的带导柱锥柄平底锪钻
Counterbores with morse taper shanks and detachable pilots
GB/T 4264-1984 带可换导柱锥柄90°锥面锪钻
本标准适用于加工GB152-76《紧固件通孔及沉头座尺寸》标准中所规定的沉头螺钉沉头座的带导柱锥柄90°锥面锪钻
90 degree countersinks with morse taper shanks and detachable pilots
GB/T 4261-2004 带可换导柱的莫氏锥柄平底锪钻
本标准规定了带可换导柱的莫氏锥柄平底锪钻的尺寸和公差
Counterbores with Morse taper shanks and detachable pilots
ISO 4204:2016 可换导柱式莫氏锥度柄90°锪钻
Countersinks, 90°, with Morse taper shanks and detachable pilots
ISO 4204:1977 可换导柱式莫氏锥度柄90°锪钻
This International Standard specifies the dimensions of 90°countersinks with Morse taper shanks and detachable pilots for general use
Countersinks, 90 degrees, with Morse taper shanks and detachable pilots
ISO 4207:1977 可换导柱式莫氏锥柄平底锪钻
This International Standard specifies the dimensions of counterbores with Morse taper shanks and detachable pilots for general use. The illustration
Counterbores with Morse taper shanks and detachable pilots
ISO 4207:2016 可换导柱式莫氏锥柄平底锪钻
This International Standard specifies the dimensions of counterbores with Morse taper shanks and detachable pilots for general use. NOTE Figure 1
Counterbores with Morse taper shanks and detachable pilots
GB/T 4264-2004 带可换导柱的莫氏锥柄90°锥面锪钻
本标准规定了带可换导柱的莫氏锥柄90°锥面锪钻的尺寸和公差
Countersinks,90°,with Morse taper shanks and detachable pilots
GB/T 4261-2004 带可换导柱的莫氏锥柄平底锪钻
Morse taper shank countersink drill with replaceable guide post
BS ISO 4204:2016 带可换导柱的莫氏锥柄90°锥面锪钻
Countersinks, 90
编辑：北检院编辑部
