GB/T 19765-2005 产品几何量技术规范(GPS).产品几何量技术规范和检验的标准参考温度
本标准规定了产品几何量技术规范和检验的标准参考温度
Geometrical Product Specifications(GPS).Standard reference temperature for geometrical product specification and verification
BS EN ISO 1:2002 产品几何量技术规范(GPS).产品几何量技术规范和验收的标准温度
This International Standard specifies the standard reference temperature for geometrical product specification and verification
Geometrical Product Specifications (GPS) - Standard reference temperature for geometrical product specification and verification
ISO 1:2002 产品几何量技术规范(GPS).产品几何量技术规范和验证的标准基准温度
Geometrical Product Specifications (GPS) - Standard reference temperature for geometrical product specification and verification
EN ISO 1:2002 产品几何量技术规范(GPS).产品几何量技术规范和验收的标准温度 ISO 1-2002
Geometrical Product Specifications (GPS) - Standard Reference Temperature for Geometrical Product Specification and Verification ISO 1:2002
ISO 14978:2006/cor 1:2008 产品几何量技术规范(GPS).产品几何量技术规范(GPS)测量设备的一般概念和要求.技术勘误表1
This standard is Geometrical product specifications (GPS) - General concepts and requirements for GPS measuring equipment; Technical Corrigendum 1
Geometrical product specifications (GPS) - General concepts and requirements for GPS measuring equipment; Technical Corrigendum 1
GB/T 12360-2005 产品几何量技术规范(GPS) 圆锥配合
本标准规定了圆锥配合的术语和定义及一般规定。 本标准适用于锥度C从1：3～1：500，长度L从6～630 mm，直径至500mm 光滑圆锥的配合。其公差的给定方法，按GB/T 11334-2005《圆锥公差》中4.2a)的规定。即： “给出公称圆锥的圆锥角α（或锥度C）和
Geometrical Product Specifications(GPS) Cone fit
GB/T 11334-2005 产品几何量技术规范(GPS) 圆锥公差
本标准规定了圆锥公差的术语和定义、圆锥公差的给定方法及公差数值。 本标准适用于锥度C从1：3～1：500、长度L从6～630 mm的光滑圆锥。本标准中的圆锥角公差也适用于按GB/T 4096给定的棱体的角度与斜度
Geometrical Product Specifications(GPS).Cone tolerance
KS B ISO TR 14638:2014 产品几何量技术规范(GPS).总体规划
Geometrical product specification(GPS) — Masterplan
BS EN ISO 3650:1999 产品几何量规范(GPS).长度标准.块规
This International Standard specifies the most important design and metrologicai characteristics of gauge blocks with a rectangular cross section
Geometrical product specifications (GPS). Length standards. Gauge blocks
ISO/TR 14638:1995 产品几何量技术规范(GPS) 总体规划
Gives the overview of the international standardization of Geometrical Product Specification (GPS). Explains the concept of GPS and provides
Geometrical product specification (GPS) - Masterplan
KS B ISO 14638:2005 产品几何量技术规范(GPS).总体规划
이 규격에서는 기하학적 제품 시방(GPS)의 표준화에 대한 개요를 확립하고 기하학적 제품의
Geometrical product specification(GPS)-Masterplan
KS B ISO TR 14638:2017 产品几何量技术规范（GPS） 总体规划
Geometrical product specification(GPS) — Masterplan
BS EN ISO 5458:1999 产品几何量规范（GPS).几何公差.位置公差
This International Standard describes positional tolerancing. This tolerancing method is applied to the location of a point, of a line nominally
Geometrical product specifications (GPS) - Geometrical tolerancing - Positional tolerancing
EN ISO 1119:2011 产品几何量规范(GPS).锥度和锥度角系列
This International Standard provides calculated values for a series of cones or conical tapers, ranging from120° to less than 1°, or ratios from 1
Geometrical product specifications (GPS) - Series of conical tapers and taper angles
EN ISO 1119:2002 产品几何量规范(GPS).锥度和锥度角系列
Geometrical product specifications (GPS) - Series of conical tapers and taper angles
GB/T 19765-2005 产品几何量技术规范(GPS).产品几何量技术规范和检验的标准参考温度
本标准规定了产品几何量技术规范和检验的标准参考温度
Geometrical Product Specifications(GPS).Standard reference temperature for geometrical product specification and verification
BS EN ISO 1:2002 产品几何量技术规范(GPS).产品几何量技术规范和验收的标准温度
This International Standard specifies the standard reference temperature for geometrical product specification and verification
Geometrical Product Specifications (GPS) - Standard reference temperature for geometrical product specification and verification
ISO 1:2002 产品几何量技术规范(GPS).产品几何量技术规范和验证的标准基准温度
Geometrical Product Specifications (GPS) - Standard reference temperature for geometrical product specification and verification
EN ISO 1:2002 产品几何量技术规范(GPS).产品几何量技术规范和验收的标准温度 ISO 1-2002
Geometrical Product Specifications (GPS) - Standard Reference Temperature for Geometrical Product Specification and Verification ISO 1:2002
ISO 14978:2006/cor 1:2008 产品几何量技术规范(GPS).产品几何量技术规范(GPS)测量设备的一般概念和要求.技术勘误表1
This standard is Geometrical product specifications (GPS) - General concepts and requirements for GPS measuring equipment; Technical Corrigendum 1
Geometrical product specifications (GPS) - General concepts and requirements for GPS measuring equipment; Technical Corrigendum 1
GB/T 12360-2005 产品几何量技术规范(GPS) 圆锥配合
本标准规定了圆锥配合的术语和定义及一般规定。 本标准适用于锥度C从1：3～1：500，长度L从6～630 mm，直径至500mm 光滑圆锥的配合。其公差的给定方法，按GB/T 11334-2005《圆锥公差》中4.2a)的规定。即： “给出公称圆锥的圆锥角α（或锥度C）和
Geometrical Product Specifications(GPS) Cone fit
GB/T 11334-2005 产品几何量技术规范(GPS) 圆锥公差
本标准规定了圆锥公差的术语和定义、圆锥公差的给定方法及公差数值。 本标准适用于锥度C从1：3～1：500、长度L从6～630 mm的光滑圆锥。本标准中的圆锥角公差也适用于按GB/T 4096给定的棱体的角度与斜度
Geometrical Product Specifications(GPS).Cone tolerance
KS B ISO TR 14638:2014 产品几何量技术规范(GPS).总体规划
Geometrical product specification(GPS) — Masterplan
BS EN ISO 3650:1999 产品几何量规范(GPS).长度标准.块规
This International Standard specifies the most important design and metrologicai characteristics of gauge blocks with a rectangular cross section
Geometrical product specifications (GPS). Length standards. Gauge blocks
ISO/TR 14638:1995 产品几何量技术规范(GPS) 总体规划
Gives the overview of the international standardization of Geometrical Product Specification (GPS). Explains the concept of GPS and provides
Geometrical product specification (GPS) - Masterplan
KS B ISO 14638:2005 产品几何量技术规范(GPS).总体规划
이 규격에서는 기하학적 제품 시방(GPS)의 표준화에 대한 개요를 확립하고 기하학적 제품의
Geometrical product specification(GPS)-Masterplan
KS B ISO TR 14638:2017 产品几何量技术规范（GPS） 总体规划
Geometrical product specification(GPS) — Masterplan
BS EN ISO 5458:1999 产品几何量规范（GPS).几何公差.位置公差
This International Standard describes positional tolerancing. This tolerancing method is applied to the location of a point, of a line nominally
Geometrical product specifications (GPS) - Geometrical tolerancing - Positional tolerancing
EN ISO 1119:2011 产品几何量规范(GPS).锥度和锥度角系列
This International Standard provides calculated values for a series of cones or conical tapers, ranging from120° to less than 1°, or ratios from 1
Geometrical product specifications (GPS) - Series of conical tapers and taper angles
EN ISO 1119:2002 产品几何量规范(GPS).锥度和锥度角系列
Geometrical product specifications (GPS) - Series of conical tapers and taper angles
编辑：北检院编辑部
