氯唑磷检测

GB 6260-1986 土壤中氧化稀土总量的测定对马尿酸偶氮氯磷分光光度法

本标准适用于一般土壤中氧化稀土总量的测定，测定范围：0.01％～0.05％。本标准不适用于ThO2/ΣRExOy*＞10％的试样的分析。

GB/T 4325.15-1984 钼化学分析方法 偶氮氯磷I光度法测定镁量

本标准适用于钼粉、钼条、三氧化铝、钼酸铵中镁量的测定。测定范围：0.00030～0.010％。

Methods for chemical analysis of molybdenum--The chlorophosphonazo 1 photometric method for the determination of magnesium content

T/CEC 423-2020 矿物绝缘油和润滑油中硫、磷、氯含量的测定能量色散X射线荧光光谱法

本文件规定了矿物绝缘油和润滑油中硫、磷、氯含量的能量色散X 射线荧光光谱测定方法。 本文件适用于矿物绝缘油和润滑油中硫、磷、氯含量的测定，其他油品和有机液体的测定也可参照使用本方法。

NB/T 10470-2020 固体生物质燃料砷、磷、氯测定方法 X射线荧光光谱法

T/CSEA 12-2019 硼、硫、磷、氯元素添加剂的金属加工液

表1　金属加工液的技术要求 序号　项    目　质量指标 　　L-MAA　L-MAB　L-MAE　L-MAF　L-MAG　L-MAH 1　浓 缩 物　外观　淡黄色至褐色透明或半透明均匀油状液　均匀液体或均匀膏状物或均匀粉剂 2　　储运安定性　明显变化 3　　硼含量/(mg/L)　≤50 4　　硫含量/( mg/L)　≤20 5　　氯含量/( mg/L)　≤20 6　　磷含量/( mg/L)　≤20 7　 稀a 释 液　透明度　不透明或半透明　透明或半透明 8　　pH值　8.0～10.0 9　　消泡性/（mL/10 min）　≤2 10　　表面张力/（mN/m）　≤40 11　　腐蚀试验a（55±2）℃，h HT300铸铁,A级 T3铜，B级 2A12铝，B级　 ≥24 ≥16 ≥16 12　　防锈试验（35±2）℃ HT300铸铁单片，24 h HT300铸铁叠片，8 h　 合格 合格 13　　安定性 油 皂　 析出 析出 14　　食盐允许量　相分离 15　　硬水适应性　未见絮状物或析出物 续表1  金属加工液的技术要求 序号　项    目　质量指标 　　L-MAA　L-MAB　L-MAE　L-MAF　L-MAG　L-MAH 16　稀释液b　对机床油漆的适应性　允许轻微失光和变色，但不允许油漆起泡、发粘、开裂和脱落 17　　亚硝酸盐含量c，mg/L　≤20 a   产品只用于黑色金属加工时，不受T3铜和2A12铝试验结果限制。 b   稀释液用蒸馏水配制，浓度（质量百分数）为5%。 B   金属加工液中不应含有亚硝酸盐。（产品在制作中不添加亚硝酸盐，在实际应用中，不排除其他原料的带入或者是反应生成）

Boron Sulfur Phosphorus Chlorine Additives-Free Metal Working Fluid

ASTM D6443-14(2019)e1 通过波长色散X射线荧光光谱法测定未使用的润滑油和添加剂中的钙 氯 铜 镁 磷 硫和锌的标准测试方法（数学校正程序）

Standard Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectr

T/CSEA 3-2018 硫、磷、氯元素添加剂的切削油

本标准规定了硫、磷、氯元素添加剂的切削油的技术要求、试验方法、检验规则、标志、包装、运输与贮存。  本标准适用于非人为添加硫、磷、氯元素添加剂的切削油，生产、管道输送等不可控因素引入除外。

Sulfur, Phosphorus and Chlorine Additives Free Cutting Oil

(EU) No 2017-626 就啶虫脒、氰虫酰胺、嘧菌环胺、乙烯利、粉唑醇、甲基磺草酮、丙环唑、嘧霉胺、戊唑醇、肟菌酯、苯醚甲环唑、氟吡菌酰胺、氟唑菌酰胺、甲基咪草烟、灭草烟、螺虫乙酯、氯氰菊酯、高效氯氟氰菊酯、丙溴磷和三唑磷在部分农产品内部或表面的最大残留限量，修订欧洲议会和理事会条例(EC) No 396/2005 的附件II 和III

(EU) No 2017-623 就双甲脒、吡氟酰草胺、氯菊酯、吡唑醚菌酯、蝇毒磷、氟甲喹、链霉素、灭螨醌和嗪草酮在部分农产品内部或表面的最大残留限量，修订欧洲议会和理事会条例(EC) No 396/2005 的附件II 和III

SN/T 4138-2015 出口水果和蔬菜中敌敌畏、四氯硝基笨、丙线磷等88种农药残留的筛选检测 QuEChERS-气相色谱-负化学源质谱法

本标准规定了水果和蔬菜中88种农药(见附录A)残留量检测的气相色谱-负化学源质谱筛选检测方法。 本标准适用于胡萝卜、白菜、生姜、苹果、梨、黄桃、草莓、菠菜、西瓜、豇豆、火龙果等蔬菜和水果中88种农药残留量的筛选检测，本标准不适用于橙子等柑橘类水果中灭藻醌残留量的检测。

Screening detection of dichlorvos, tecnazene, ethoprophos 88 pesticide residues in exported fruits and vegetables.QuEChERS-GC-NCI-MS method

ASTM D6443-14 通过波长色散X射线荧光光谱法测定未使用的润滑油和添加剂中的钙 氯 铜 镁 磷 硫和锌的标准测试方法（数学校正程序）

Standard Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectr

NB/SH/T 0880-2014 润滑油及添加剂中的钙、氯、铜、镁、磷、硫和锌含量的测定 波长色散X射线荧光光谱法

本标准规定了采用波长色散X射线荧光光谱法测定润滑油及添加剂中的钙、氯、铜、镁、磷、硫和锌的含量的方法。本标准适用于测定润滑油、添加剂和复合剂中钙、氯、铜、镁、磷、硫和锌的含量。当样品中元素浓度超出标准曲线的上限时,可以经过稀释后再检测。

Standard test method for determination of calcium, chlorine, copper, magnesium ,phosphorus, sulfur, and zinc in unused lubricating oils and additives by wavelength dispersive X-ray fluorescence spectrometry (mathematical correction procedure)

ASTM D6443-2014 采用波长色散X射线荧光光谱法测定未用润滑油和添加剂中钙, 氯, 铜, 镁, 磷, 硫和锌的标准试验方法 (数学校正规程)

4.1x00a0;Lubricating oils can be formulated with additives, which can act as detergents, anti-oxidants, anti-wear agents, and so forth. Some additives can contain one or more of calcium, copper, magnesium, phosphorus, sulfur, and zinc. This test method can be used to determine if the oils, additives, and additive packages meet specification with respect to content of these elements. 4.2x00a0;Several additive elements and their compounds are added to the lubricating oils to give beneficial performance (Table 3). 4.3x00a0;This test method can also be used to determine if lubricating oils, additives, and additive packages meet specification with respect to chlorine concentration. In this context, specification can refer to contamination. 4.4x00a0;This test method is not intended for use on samples that contain some component that significantly interferes with the analysis of the elements specified in the scope. 4.5x00a0;This test method can complement other test methods for lube oils and additives, including Test Methods D4628, D4927, D4951, and D5185. 1.1x00a0;This test method covers the determination of calcium, chlorine, copper, magnesium, phosphorus, sulfur, and zinc in unused lubricating oils, additives, and additive packages by wavelength dispersive X-ray fluorescence spectrometry. Matrix effects are handled with mathematical corrections. 1.2x00a0;For each element, the upper limit of the concentration range covered by this test method is defined by the highest concentration listed in Table 1. Samples containing higher concentrations can be analyzed following dilution. 1.3x00a0;For each element, the lower limit of the concentration range covered by this test method can be estimated by the limit of detection (LOD)2 (see also 408201;CFR 136 Appendix B) or limit of quantification (LOQ),2 both of which can be estimated from Sr, the repeatability standard deviation. LOD and LOQ values, determined from results obtained in the interlaboratory study on precision, are listed in Table 2. 1.3.1x00a0;LOD and LOQ are not intrinsic constants of this test method. LOD and LOQ depend upon the precision attainable by a laboratory when using this test method. 1.4x00a0;This test method uses regression software to determine calibration parameters, which can include influence coefficients (that is, interelement effect coefficients) (Guide E1361), herein referenced as alphas. Alphas can also be determined from ......

Standard Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectrometry (Mathematical Correction Procedure)

SN/T 2697-2010 进出口煤炭中硫、磷、砷和氯的测定 X射线荧光光谱法

本标准规定了煤炭中硫、磷、砷和氯含量的X射线荧光光谱测定方法。 本标准适用于进出口烟煤、烟煤和褐煤中硫、磷、砷和氯含量的测定。

Determination of sulfur,phosphorus,arsenic and chloride in coal for import and export.X-ray fluorescence spectrometric method

ASTM D6443-04(2010) 用波长色散X射线荧光光谱法测定未使用润滑油和添加剂中钙、氯、铜、镁、磷、硫和锌的试验方法（数学校正程序）

Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectrometry (M

741药典 化学药和生物制品卷-2010 第九章 内分泌系统用药 第八节 钙、磷代谢调节药 三、抗骨质疏松药 (一)抑制骨吸收药 氯曲膦酸钠

来自第614页

1382药典 化学药和生物制品卷-2010 第二十章 解毒药 第二节 特异性解毒药 二、有机磷毒物中毒解毒药 氯解磷定

来自第1223页

NY 1500.46.2-2008 农药最大残留限量氯唑磷蔬菜

本标准规定了蔬菜、水果中甲胺磷等 20 种农药的最大残留限量。 本标准适用于表 1 所列农药对应的蔬菜、水果。

NY 1500.46.1-2008 农药最大残留限量氯唑磷水果

本标准规定了蔬菜、水果中甲胺磷等 20 种农药的最大残留限量。 本标准适用于表 1 所列农药对应的蔬菜、水果。

ASTM D6443-04 用波长色散X射线荧光光谱法测定未使用润滑油和添加剂中钙、氯、铜、镁、磷、硫和锌的试验方法（数学校正程序）

Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectrometry (M

ASTM D6443-2004 波长色散X射线荧光光谱法测定未用润滑油和添加剂中钙、氯、铜、镁、磷、硫和锌的标准试验方法(数学修正程序)

Lubricating oils can be formulated with additives, which can act as detergents, anti-oxidants, anti-wear agents, and so forth. Some additives can contain one or more of calcium, copper, magnesium, phosphorus, sulfur, and zinc. This test method can be used to determine if the oils, additives, and additive packages meet specification with respect to content of these elements. This test method can also be used to determine if lubricating oils, additives, and additive packages meet specification with respect to chlorine concentration. In this context, specification can refer to contamination. This test method is not intended for use on samples that contain some component that significantly interferes with the analysis of the elements specified in the scope. This test method can complement other test methods for lube oils and additives, including Test Methods D 4628, D 4927, D 4951, and D 5185.1.1 This test method covers the determination of calcium, chlorine, copper, magnesium, phosphorus, sulfur, and zinc in unused lubricating oils, additives, and additive packages by wavelength dispersive X-ray fluorescence spectrometry. Matrix effects are handled with mathematical corrections.1.2 For each element, the upper limit of the concentration range covered by this test method is defined by the highest concentration listed in . Samples containing higher concentrations can be analyzed following dilution.1.3 For each element, the lower limit of the concentration range covered by this test method can be estimated by the limit of detection (LOD) (see also 40 CFR 136 Appendix B) or limit of quantification (LOQ), both of which can be estimated from Sr, the repeatability standard deviation. LOD and LOQ values, determined from results obtained in the interlaboratory study on precision, are listed in .1.3.1 LOD and LOQ are not intrinsic constants of this test method. LOD and LOQ depend upon the precision attainable by a laboratory when using this test method.1.4 This test method uses regression software to determine calibration parameters, which can include influence coefficients (that is, interelement effect coefficients) (Guide E 1361), herein referenced as alphas. Alphas can also be determined from theory using relevant software.1.5 Setup of this test method is intended for persons trained in the practice of X-ray spectrometry. Following setup, this test method can be used routinely.1.6 The values stated in either SI units or angstrom units are to be regarded separately as standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectrometry (Mathematical Correction Procedure)

ASTM D6443-2004(2010) 波长色散X射线荧光光谱法测定未用润滑油和添加剂中钙、氯、铜、镁、磷、硫和锌的标准试验方法(数学校正规程)

Lubricating oils can be formulated with additives, which can act as detergents, anti-oxidants, anti-wear agents, and so forth. Some additives can contain one or more of calcium, copper, magnesium, phosphorus, sulfur, and zinc. This test method can be used to determine if the oils, additives, and additive packages meet specification with respect to content of these elements. This test method can also be used to determine if lubricating oils, additives, and additive packages meet specification with respect to chlorine concentration. In this context, specification can refer to contamination. This test method is not intended for use on samples that contain some component that significantly interferes with the analysis of the elements specified in the scope. This test method can complement other test methods for lube oils and additives, including Test Methods D4628, D4927, D4951, and D5185.1.1 This test method covers the determination of calcium, chlorine, copper, magnesium, phosphorus, sulfur, and zinc in unused lubricating oils, additives, and additive packages by wavelength dispersive X-ray fluorescence spectrometry. Matrix effects are handled with mathematical corrections. 1.2 For each element, the upper limit of the concentration range covered by this test method is defined by the highest concentration listed in Table 1. Samples containing higher concentrations can be analyzed following dilution. 1.3 For each element, the lower limit of the concentration range covered by this test method can be estimated by the limit of detection (LOD) (see also 40 CFR 136 Appendix B) or limit of quantification (LOQ), both of which can be estimated from Sr, the repeatability standard deviation. LOD and LOQ values, determined from results obtained in the interlaboratory study on precision, are listed in Table 2. 1.3.1 LOD and LOQ are not intrinsic constants of this test method. LOD and LOQ depend upon the precision attainable by a laboratory when using this test method. 1.4 This test method uses regression software to determine calibration parameters, which can include influence coefficients (that is, interelement effect coefficients) (Guide E1361), herein referenced as alphas. Alphas can also be determined from theory using relevant software. 1.5 Setup of this test method is intended for persons trained in the practice of X-ray spectrometry. Following setup, this test method can be used routinely. 1.6 The values stated in either SI units or angstrom units are to be regarded separately as standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectrometry (Mathematical Correction Procedure)

ASTM D6443-99 用波长色散X射线荧光光谱法测定未使用润滑油和添加剂中钙、氯、铜、镁、磷、硫和锌的试验方法（数学校正程序）

Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectrometry (M

ASTM D6443-1999 波长色散X射线荧光光谱法测定未用润滑油和添加剂中钙、氯、铜、镁、磷、硫和锌的试验方法(数学修正程序)

1.1 This test method covers the determination of calcium, chlorine, copper, magnesium, phosphorus, sulfur, and zinc in unused lubricating oils, additives, and additive packages by wavelength dispersive X-ray fluorescence spectrometry. Matrix effects are handled with mathematical corrections. 1.2 For each element, the upper limit of the concentration range covered by this test method is defined by the highest concentration listed in Table 1. Samples containing higher concentrations can be analyzed following dilution. 1.3 For each element, the lower limit of the concentration range covered by this test method can be estimated by the limit of detection (LOD) (see also 40 CFR 136 Appendix B) or limit of quantification (LOQ), both of which can be estimated from Sr, the repeatability standard deviation. LOD and LOQ values, determined from results obtained in the interlaboratory study on precision, are listed in Table 2. 1.3.1 LOD and LOQ are not instrinsic constants of this test method. LOD and LOQ depend upon the precision attainable by a laboratory when using this test method. 1.4 This test method uses regression software to determine calibration parameters, which can include influence coefficients (that is, interelement effect coefficients) (Guide E1361), herein referenced as alphas. Alphas can also be determined from theory using relevant software. 1.5 Setup of this test method is intended for persons trained in the practice of X-ray spectrometry. Following setup, this test method can be used routinely. 1.6 The values stated in either SI units or angstrom units are to be regarded separately as standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectrometry (Mathematical Correction Procedure)

SNI 06-2599-1992 工业等级氯蜱硫磷

Technical grade chlor pirifos

SNI 02-2889-1992 浓缩氯蜱硫磷杀虫剂

Emulsifable concentrate chlorphyrifos pesticides

PN Z04073-05-1988 空气纯度保护．磷及其化合物的含量测试．在可见光下用光度法测定工作场所中的氯氧化磷

Air purity protection Tests for phosphorus and its compounds Determination of phosphorus oxychloride in work places by spectrophotometry in visible light

NY/T 30-1986 土壤中氧化稀土总量的测定.对马尿酸偶氮氯磷分光光度法

Determination of rare earth oxide content in soil.Chlorophosphonazo-p-hippuric acid photometric method

ANSI K62.219-1978 混氯甲硫磷(chlorthiophos)－(杀虫剂)通用名称

Provides the accepted common name for the chemical compound given. Includes the use of the common name and the physical and chemical properties of the chemical compound.

Common Name for the Pest Control Chemical O-(2,5-Dichloro-4- (methylthio)phenyl) O,O-diethyl Phosphorothioate and the 2,4,5 and 4,5,2 Isomers (73:14:13) "Chlorthiophos"

STAS 10966-1977 氯、磷、砷含量的测定

1 Prezentul standard stabile?te metodele pentru determinarea clorului, fosforului ?i ar-senului din combustibilii solizi. 2 Reactivii folosi?i la analize, dac? nu s?nt specificate alte condi?ii de puritate, vor fi de calitate pentru analiz? (p.

Determination of chlorine, phosphorus and arsenic content

ANSI K62.130-1973 甲基氯吡磷(chlorpyrifos-methyl)－(杀虫剂)通用名称

Provides the accepted common name for the chemical compound given. Includes the use of the common name and the physical and chemical properties of the chemical compound.

Common Name for the Pest Control Chemical 0,0-Dimethyl 0-(3,5,6-Trichloro-2-pyridyl) Phosphorothioate "Chlorpyrifos-Methyl"

ANSI K62.111-1971 甲基氯吡磷(fospirate)－(驱虫剂和杀虫剂)通用名称

Provides the accepted common name for the chemical compound given. Includes the use of the common name and the physical and chemical properties of the chemical compound.

Common Name for the Pest Control Chemical Dimethyl 3,5,6-Trichloro-2-pyridyl Phosphate "Fospirate"

ANSI K62.103-1971 氯吡磷(chlorpyrifos)－(杀虫剂)通用名称

Provides the accepted common name for the chemical compound given. Includes the use of the common name and the physical and chemical properties of the chemical compound.

Common Name for the Pest Control Chemical 0,0-Diethyl 0-(3,5,6-Trichloro-2-pyridyl) Phosphorothioate "Chlorpyrifos"

ANSI K62.87-1969 氯乙亚胺磷(dialifor)－(杀虫剂)通用名称

Provides the accepted common name for the chemical compound given. Includes the use of the common name and the physical and chemical properties of the chemical compound.

Common Name for the Pest Control Chemical O,O-Diethyl Phosphorodithioate S-Ester with N-(2-Chloro- 1-mercaptoethyl) phthalimide "Dialifor"

T/CEC 423-2020 矿物绝缘油和润滑油中硫、磷、氯含量的测定 能量色散X射线荧光光谱法