DL/T 764.4-2002 输电线路铁塔及电力金具紧固用冷镦热浸镀锌螺栓与螺母
Cold forging hot dip galvanizing bolt and nut for tower and hardware of transmission lines
DL/T 284-2012 输电线路杆塔及电力金具用热浸镀锌螺栓与螺母
本标准规定了螺纹规格为M10～M64的输电线路杆塔及电力金具用热浸镀锌六角头螺栓（以下简称为螺栓）、六角螺母（以下简称为螺母）、六角薄螺母（以下简称为薄螺母）和脚钉的型式尺寸、技术要求、试验方法的运用及适用性、试验方法、验收检查和组配包装与标识，以及采用加大攻丝尺寸的内螺纹，以容纳热浸镀锌层，满足
Hot-dip galvanized bolts and nuts for tower And hardware of transmission lines
DL/T 284-2021 输电线路杆塔及电力金具用热浸镀锌螺栓与螺母
Hot-dip galvanized bolts and nuts for transmission line towers and power fittings
T/ZZB 0345-2018 电力线路用热浸镀锌螺栓、螺母和垫圈
本标准规定了电力线路用热浸镀锌螺栓、螺母和垫圈的术语和定义、基本要求、技术要求、试验方法、检验规则、标识、组配包装、运输和存储及质量承诺。 本标准适用于工作环境温度为-50℃～+150℃，公称直径为10mm～64mm的电力线路用热浸镀锌螺栓、螺母和垫圈
Hot-dip galvanized bolts, nuts and washers for transmission lines
T/CISA 193-2021 输电铁塔用耐候钢螺栓与螺母
本文件规定了输电铁塔用耐候钢螺栓与螺母的术语和定义、型式、尺寸及公差、技术要求、检验项目及验收检查、试验方法、标志、包装及质量证明书。 本文件适用于大气腐蚀性等级为C1～C3、螺纹规格为M10～M39的耐候钢六角头螺栓（以下简称“螺栓”）、耐候钢脚钉（以下简称脚钉）、耐候钢六角螺母（以下简称“螺母
Weathering steel bolts and nuts for transmission towers
AS 1559:2018 用于塔架结构的热浸镀锌钢螺栓及相关螺母和垫圈
Specifies the requirements for hot-dip galvanized bolts and step bolts with ISO metric coarse pitch series threads for normal and low temperature
Hot-dip galvanized steel bolts and associated nuts and washers for tower construction
DL/T 1236-2013 输电杆塔用地脚螺栓与螺母
本标准规定了螺纹规格M20~M100,性能等级为4.6、5.6级和8.8级输电杆塔用地脚螺栓及螺母的型式与尺寸、技术条件、试验项目及验收检查、试验方法组配与包装。本标准适用于架空输电线路杆塔用地脚螺栓与螺母,其他钢结构用地脚螺栓与螺母可参照本标准
Anchor bolts and nuts for poles and towers of electric power transmission line
CNS 4237-2000 热浸镀锌螺栓及螺帽
本标准适用于经由热浸镀锌而得有镀层之螺栓及螺帽，其螺纹标称为从 M10 至 M36 者
Hot dip galvanized bolts and nuts
ASTM F2329/F2329M-15(2023 碳钢和合金钢螺栓、螺钉、垫圈、螺母和特殊螺纹紧固件的热浸镀锌要求
Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
Q/GDW637-2011 输电杆塔用地脚螺栓与螺母
DL/T 1236-2021 输电杆塔用地脚螺栓与螺母
Anchor bolts and nuts for transmission towers
ASTM F2329-05 碳钢和合金钢螺栓、螺钉、垫圈、螺母和特殊螺纹紧固件用热浸镀锌覆层的标准规范
1.1 This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts
Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
ASTM F2329-05(2011 碳钢和合金钢螺栓,螺钉,垫圈,螺母,和特殊螺纹紧固件用热浸镀锌覆层的标准规范
1.1 This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers
Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
ASTM F2674-07 碳钢和合金钢螺栓、螺钉、垫圈、螺母和特殊螺纹紧固件用热浸镀锌覆层的标准规范
1.1 This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers
Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners [Metric]
ASTM A394-07 钢制输电塔镀锌螺栓和裸螺栓用标准规范
1.1 This specification covers the chemical and mechanical requirements of hexagon and square-head zinc-coated steel bolts and atmospheric
Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare
DL/T 764.4-2002 输电线路铁塔及电力金具紧固用冷镦热浸镀锌螺栓与螺母
Cold forging hot dip galvanizing bolt and nut for tower and hardware of transmission lines
DL/T 284-2012 输电线路杆塔及电力金具用热浸镀锌螺栓与螺母
本标准规定了螺纹规格为M10～M64的输电线路杆塔及电力金具用热浸镀锌六角头螺栓（以下简称为螺栓）、六角螺母（以下简称为螺母）、六角薄螺母（以下简称为薄螺母）和脚钉的型式尺寸、技术要求、试验方法的运用及适用性、试验方法、验收检查和组配包装与标识，以及采用加大攻丝尺寸的内螺纹，以容纳热浸镀锌层，满足
Hot-dip galvanized bolts and nuts for tower And hardware of transmission lines
DL/T 284-2021 输电线路杆塔及电力金具用热浸镀锌螺栓与螺母
Hot-dip galvanized bolts and nuts for transmission line towers and power fittings
T/ZZB 0345-2018 电力线路用热浸镀锌螺栓、螺母和垫圈
本标准规定了电力线路用热浸镀锌螺栓、螺母和垫圈的术语和定义、基本要求、技术要求、试验方法、检验规则、标识、组配包装、运输和存储及质量承诺。 本标准适用于工作环境温度为-50℃～+150℃，公称直径为10mm～64mm的电力线路用热浸镀锌螺栓、螺母和垫圈
Hot-dip galvanized bolts, nuts and washers for transmission lines
T/CISA 193-2021 输电铁塔用耐候钢螺栓与螺母
本文件规定了输电铁塔用耐候钢螺栓与螺母的术语和定义、型式、尺寸及公差、技术要求、检验项目及验收检查、试验方法、标志、包装及质量证明书。 本文件适用于大气腐蚀性等级为C1～C3、螺纹规格为M10～M39的耐候钢六角头螺栓（以下简称“螺栓”）、耐候钢脚钉（以下简称脚钉）、耐候钢六角螺母（以下简称“螺母
Weathering steel bolts and nuts for transmission towers
AS 1559:2018 用于塔架结构的热浸镀锌钢螺栓及相关螺母和垫圈
Specifies the requirements for hot-dip galvanized bolts and step bolts with ISO metric coarse pitch series threads for normal and low temperature
Hot-dip galvanized steel bolts and associated nuts and washers for tower construction
DL/T 1236-2013 输电杆塔用地脚螺栓与螺母
本标准规定了螺纹规格M20~M100,性能等级为4.6、5.6级和8.8级输电杆塔用地脚螺栓及螺母的型式与尺寸、技术条件、试验项目及验收检查、试验方法组配与包装。本标准适用于架空输电线路杆塔用地脚螺栓与螺母,其他钢结构用地脚螺栓与螺母可参照本标准
Anchor bolts and nuts for poles and towers of electric power transmission line
CNS 4237-2000 热浸镀锌螺栓及螺帽
本标准适用于经由热浸镀锌而得有镀层之螺栓及螺帽，其螺纹标称为从 M10 至 M36 者
Hot dip galvanized bolts and nuts
ASTM F2329/F2329M-15(2023 碳钢和合金钢螺栓、螺钉、垫圈、螺母和特殊螺纹紧固件的热浸镀锌要求
Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
Q/GDW637-2011 输电杆塔用地脚螺栓与螺母
DL/T 1236-2021 输电杆塔用地脚螺栓与螺母
Anchor bolts and nuts for transmission towers
ASTM F2329-05 碳钢和合金钢螺栓、螺钉、垫圈、螺母和特殊螺纹紧固件用热浸镀锌覆层的标准规范
1.1 This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts
Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
ASTM F2329-05(2011 碳钢和合金钢螺栓,螺钉,垫圈,螺母,和特殊螺纹紧固件用热浸镀锌覆层的标准规范
1.1 This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers
Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
ASTM F2674-07 碳钢和合金钢螺栓、螺钉、垫圈、螺母和特殊螺纹紧固件用热浸镀锌覆层的标准规范
1.1 This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers
Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners [Metric]
ASTM A394-07 钢制输电塔镀锌螺栓和裸螺栓用标准规范
1.1 This specification covers the chemical and mechanical requirements of hexagon and square-head zinc-coated steel bolts and atmospheric
Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare
编辑：北检院编辑部
