HG/T 3036-2009 饱和蒸汽用橡胶软管及软管组合件.规范
本标准规定了对两个型别的软管及软管组合件的要求，最大工作压力为0.6MPa的低压软管及软管组合件和最大工作压力为1.8MPa的高压软管及软管组合件都由橡胶软管和金属接头组成，用于输送饱和蒸汽和冷凝水。 每个型别都分为外覆层耐油和外覆层不耐油两个等级
Rubber hoses and hose assemblies for saturated steam.Specification
GB/T 18425-2014 蒸汽橡胶软管和软管组合件 试验方法
本标准规定「软管或软管组合件试样通入饱和蒸汽以模拟使用条件的四种试验方法。 即﹕一A法=垂窒直台架法;一B法=水平台架法薯C法=垂直安装曲挠试验法=一D法=水平安装曲挠试验法。 注意:应配备]切必要的安伞设备〉以确保操作人员有安仝的工作条件
Rubber hoses and hose assemblies for steam.Test methods
HG/T 3036-1999 蒸汽橡胶软管及软管组合件
本标准规定了织物增强、内壁光滑的吸排水软管的最低要求。 该软管分为两个型别： -1型：吸水压力可达-63 kPa(-630 mbar)、排水压力可达0.3 MPa(3 bar)的温和条件下使用的软管； -2型：吸水压力可达-80 kPa(-800 mbar)、排水压
Rubber hoses and hose assemblies for steam
EN ISO 6134:2005 橡胶软管和软管组件的饱和蒸汽
Rubber hoses and hose assemblies for saturated steam - Specification
KS M ISO 6134:2012 饱和蒸汽用橡胶软管和软管组件.规范
이 표준은 최대 작동 압력 6 bar를 저압으로 하고 최대 작동 압력 18 bar를 고압으
Rubber hoses and hose assemblies for saturated steam－Specification
BS EN ISO 6134:2005 饱和蒸汽用橡胶软管和软管组件.规范
This document specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high
Rubber hoses and hose assemblies for saturated steam - Specification
ISO 6134:2005 饱和蒸汽用橡胶软管和软管组件.规范
This document specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high
Rubber hoses and hose assemblies for saturated steam - Specification
NF T47-263:2005 饱和蒸汽用橡胶软管和软管组件.规范
Rubber hoses and hose assemblies for saturated steam - Specification.
prEN 6134 rev 饱和蒸汽用橡胶软管和软管组件规范
ISO 6134:2017 specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high
Rubber hoses and hose assemblies for saturated steam - Specification
NF T47-263*NF EN ISO 6134:2017 饱和蒸汽用橡胶软管和软管组件规范
Rubber hoses and hose assemblies for saturated steam - Specification
DS/EN ISO 6134:2005 饱和蒸汽用橡胶软管和软管组件规范
This document specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high
Rubber hoses and hose assemblies for saturated steam - Specification
KS M ISO 6134-2017(2022 饱和蒸汽用橡胶软管和软管组件.规范
Rubber hoses and hose assemblies for saturated steam — Specification
KS M ISO 6134:2017 饱和蒸汽用橡胶软管和软管组件 规范
Rubber hoses and hose assemblies for saturated steam — Specification
BS EN ISO 6134:2017 饱和蒸汽用橡胶软管和软管组件.规范
Rubber hoses and hose assemblies for saturated steam. Specification
DIN EN ISO 6134:2017-06 饱和蒸汽用橡胶软管和软管组件 规范
Rubber hoses and hose assemblies for saturated steam - Specification (ISO 6134:2017); German version EN ISO 6134:2017
HG/T 3036-2009 饱和蒸汽用橡胶软管及软管组合件.规范
本标准规定了对两个型别的软管及软管组合件的要求，最大工作压力为0.6MPa的低压软管及软管组合件和最大工作压力为1.8MPa的高压软管及软管组合件都由橡胶软管和金属接头组成，用于输送饱和蒸汽和冷凝水。 每个型别都分为外覆层耐油和外覆层不耐油两个等级
Rubber hoses and hose assemblies for saturated steam.Specification
GB/T 18425-2014 蒸汽橡胶软管和软管组合件 试验方法
本标准规定「软管或软管组合件试样通入饱和蒸汽以模拟使用条件的四种试验方法。 即﹕一A法=垂窒直台架法;一B法=水平台架法薯C法=垂直安装曲挠试验法=一D法=水平安装曲挠试验法。 注意:应配备]切必要的安伞设备〉以确保操作人员有安仝的工作条件
Rubber hoses and hose assemblies for steam.Test methods
HG/T 3036-1999 蒸汽橡胶软管及软管组合件
本标准规定了织物增强、内壁光滑的吸排水软管的最低要求。 该软管分为两个型别： -1型：吸水压力可达-63 kPa(-630 mbar)、排水压力可达0.3 MPa(3 bar)的温和条件下使用的软管； -2型：吸水压力可达-80 kPa(-800 mbar)、排水压
Rubber hoses and hose assemblies for steam
EN ISO 6134:2005 橡胶软管和软管组件的饱和蒸汽
Rubber hoses and hose assemblies for saturated steam - Specification
KS M ISO 6134:2012 饱和蒸汽用橡胶软管和软管组件.规范
이 표준은 최대 작동 압력 6 bar를 저압으로 하고 최대 작동 압력 18 bar를 고압으
Rubber hoses and hose assemblies for saturated steam－Specification
BS EN ISO 6134:2005 饱和蒸汽用橡胶软管和软管组件.规范
This document specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high
Rubber hoses and hose assemblies for saturated steam - Specification
ISO 6134:2005 饱和蒸汽用橡胶软管和软管组件.规范
This document specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high
Rubber hoses and hose assemblies for saturated steam - Specification
NF T47-263:2005 饱和蒸汽用橡胶软管和软管组件.规范
Rubber hoses and hose assemblies for saturated steam - Specification.
prEN 6134 rev 饱和蒸汽用橡胶软管和软管组件规范
ISO 6134:2017 specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high
Rubber hoses and hose assemblies for saturated steam - Specification
NF T47-263*NF EN ISO 6134:2017 饱和蒸汽用橡胶软管和软管组件规范
Rubber hoses and hose assemblies for saturated steam - Specification
DS/EN ISO 6134:2005 饱和蒸汽用橡胶软管和软管组件规范
This document specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high
Rubber hoses and hose assemblies for saturated steam - Specification
KS M ISO 6134-2017(2022 饱和蒸汽用橡胶软管和软管组件.规范
Rubber hoses and hose assemblies for saturated steam — Specification
KS M ISO 6134:2017 饱和蒸汽用橡胶软管和软管组件 规范
Rubber hoses and hose assemblies for saturated steam — Specification
BS EN ISO 6134:2017 饱和蒸汽用橡胶软管和软管组件.规范
Rubber hoses and hose assemblies for saturated steam. Specification
DIN EN ISO 6134:2017-06 饱和蒸汽用橡胶软管和软管组件 规范
Rubber hoses and hose assemblies for saturated steam - Specification (ISO 6134:2017); German version EN ISO 6134:2017
编辑：北检院编辑部
