GB/T 3632-1995 钢结构用扭剪型高强度螺栓连接副
本标准规定了螺纹规格为M16～M24扭剪型高强度螺栓连接副的型式尺寸、技术条件及标记方法。 本标准适用于工业与民用建筑、公路与铁路桥梁、塔架、管道支架、起重机械及其他钢结构用摩擦型连接的扭剪型高强度螺栓连接副
Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures
GB/T 3632-2008 钢结构用扭剪型高强度螺栓连接副
本标准规定了螺纹规格为M16～M30钢结构用扭剪型高强度螺栓连接副的型式尺寸、技术要求、试验方法、标记方法及验收与包装。 本标准适用于工业与民用建筑、桥梁、塔桅结构、锅炉钢结构、起重机机械及其他钢结构用扭剪型高强度螺栓连接副
Sets of torshear type high strengh bolt hexagon nut and plain washer for steel structures
GB/T 3633-1995 钢结构用扭剪型高强度螺栓连接副 技术条件
本标准规定了钢结构用扭剪型高强度螺栓连接副的技术要求、试验方法、验收与包装。 本标准适用于工业与民用建筑、公路与铁路桥梁、塔架、管道支架、起重机械及其他钢结构用摩擦型连接的扭剪型高强度螺栓连接副
Technical requirement for sets of torshear type high strength bolt hexagon nut and plain washer for steel structures
SANS 10094:2005 扭剪式高强度螺栓的使用
Covers the assembly and inspection of bolted friction-grip joints in structural steelwork, i.e. joints in which high-strength bolts or equivalent
The use of high-strength friction-grip bolts
GB/T 32076.8-2017 预载荷高强度栓接结构连接副 第8部分：扭剪型圆头螺栓和螺母连接副
GB/T32076 的本部分与GB/T32076.1 规定了螺纹规格为M12一M36 .性能等级为10.9/10 、预载荷高强度栓接结构用捏剪型圆头螺栓和螺母连接副(以下简称栓接连接副)。 本部分设计的栓接连接副允许的预载荷之0.7R-XA.…。 本部分规定的栓接连接副由一个螺栓.一个螺母和一个垫圈
High-strength structural bolting assemblies for preloading—Part 8: Torshear type bolt with cup head,and nut assemblies
KS B 2819-2013 结构缝剪断型高张力螺栓.六角螺母·平垫圈扭矩
이 표준은 주로 강 구조물에 체결되어 온도 0℃∼60℃ 범위에서 사용하는 강 구조물용 토크-전단형고장력 볼트, 6각 너트, 평와셔의 세트(이하 세트라 한다.)에 대하여 규정한다
Sets of torque-shear type high tension bolt, hexagon nut and plain washer for structural joints
KS B 2819-2005 结构缝剪断型高张力螺栓.六角螺母·平垫圈扭矩
? ??? ?? ? ???? ???? ?? 0?60
Sets of torque-shear type high tension bolt, hexagon nut and plain washer for structural joints
KS B 2819-2016 结构连接用扭剪式高强度螺栓、六角螺母、平垫圈组套
Sets of torque-shear type high tension bolt, hexagon nut and plain washer for structural joints
GB/T 32076.9-2017 预载荷高强度栓接结构连接副 第9部分：扭剪型大六角头螺栓和螺母连接副
High-strength structural bolting assemblies for preloading—Part 9: Torshear type bolt with hexagon head with large width across flats，and nut assemblies
AIA/NAS NAS 1973-1986 (Rev. 5)108ksi 剪力高扭矩及扭矩调整100度头平螺栓
NAS1972THRUNAS1980, IfBolt, Flat, 100 Deg. Head, Torq-Set and Hi-Torque, 108 K S I Shear", was adopted on 13-SEP-95 for use by the Department
Bolt, Flat, 100 Degrees Head, Torq-Set and Hi-Torque, 108 ksi Shear (Rev. 5)
AIA/NAS NAS 1974-1986 (Rev. 5)108ksi 剪力高扭矩及扭矩调整100度头平螺栓
NAS1972THRUNAS1980, IfBolt, Flat,1 00 Deg. Head, Torq-Set and Hi-Torque, 108 KSI Shear", was adopted on 13-SEP-95 for use by the Department
Bolt, Flat, 100 Degrees Head, Torq-Set and Hi-Torque, 108 ksi Shear (Rev. 5)
AIA/NAS NAS 1975-1986 (Rev. 5)108ksi 剪力高扭矩及扭矩调整100度头平螺栓
NAS1972THRUNAS1980, IfBolt, Flat, 100 Deg. Head, Torq-Set and Hi-Torque, 108 K S I Shear", was adopted on 13-SEP-95 for use by the Department
Bolt, Flat, 100 Degrees Head, Torq-Set and Hi-Torque, 108 ksi Shear (Rev. 5)
AIA/NAS NAS 1976-1986 (Rev. 5)108ksi 剪力高扭矩及扭矩调整100度头平螺栓
NAS1972THRUNAS1980, IfBolt, Flat, 100 Deg. Head, Torq-Set and Hi-Torque, 108 K S I Shear", was adopted on 13-SEP-95 for use by the Department
Bolt, Flat, 100 Degrees Head, Torq-Set and Hi-Torque, 108 ksi Shear (Rev. 5)
AIA/NAS NAS 1977-1986 (Rev. 5)108ksi 剪力高扭矩及扭矩调整100度头平螺栓
NAS1972THRUNAS1980, IfBolt, Flat, 100 Deg. Head, Torq-Set and Hi-Torque, 108 K S I Shear", was adopted on 13-SEP-95 for use by the Department
Bolt, Flat, 100 Degrees Head, Torq-Set and Hi-Torque, 108 ksi Shear (Rev. 5)
AIA/NAS NAS 1978-1986 (Rev. 5)108ksi 剪力高扭矩及扭矩调整100度头平螺栓
NAS1972THRUNAS1980, IfBolt, Flat, 100 Deg. Head, Torq-Set and Hi-Torque, 108 K S I Shear", was adopted on 13-SEP-95 for use by the Department
Bolt, Flat, 100 Degrees Head, Torq-Set and Hi-Torque, 108 ksi Shear (Rev. 5)
GB/T 3632-1995 钢结构用扭剪型高强度螺栓连接副
本标准规定了螺纹规格为M16～M24扭剪型高强度螺栓连接副的型式尺寸、技术条件及标记方法。 本标准适用于工业与民用建筑、公路与铁路桥梁、塔架、管道支架、起重机械及其他钢结构用摩擦型连接的扭剪型高强度螺栓连接副
Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures
GB/T 3632-2008 钢结构用扭剪型高强度螺栓连接副
本标准规定了螺纹规格为M16～M30钢结构用扭剪型高强度螺栓连接副的型式尺寸、技术要求、试验方法、标记方法及验收与包装。 本标准适用于工业与民用建筑、桥梁、塔桅结构、锅炉钢结构、起重机机械及其他钢结构用扭剪型高强度螺栓连接副
Sets of torshear type high strengh bolt hexagon nut and plain washer for steel structures
GB/T 3633-1995 钢结构用扭剪型高强度螺栓连接副 技术条件
本标准规定了钢结构用扭剪型高强度螺栓连接副的技术要求、试验方法、验收与包装。 本标准适用于工业与民用建筑、公路与铁路桥梁、塔架、管道支架、起重机械及其他钢结构用摩擦型连接的扭剪型高强度螺栓连接副
Technical requirement for sets of torshear type high strength bolt hexagon nut and plain washer for steel structures
SANS 10094:2005 扭剪式高强度螺栓的使用
Covers the assembly and inspection of bolted friction-grip joints in structural steelwork, i.e. joints in which high-strength bolts or equivalent
The use of high-strength friction-grip bolts
GB/T 32076.8-2017 预载荷高强度栓接结构连接副 第8部分：扭剪型圆头螺栓和螺母连接副
GB/T32076 的本部分与GB/T32076.1 规定了螺纹规格为M12一M36 .性能等级为10.9/10 、预载荷高强度栓接结构用捏剪型圆头螺栓和螺母连接副(以下简称栓接连接副)。 本部分设计的栓接连接副允许的预载荷之0.7R-XA.…。 本部分规定的栓接连接副由一个螺栓.一个螺母和一个垫圈
High-strength structural bolting assemblies for preloading—Part 8: Torshear type bolt with cup head,and nut assemblies
KS B 2819-2013 结构缝剪断型高张力螺栓.六角螺母·平垫圈扭矩
이 표준은 주로 강 구조물에 체결되어 온도 0℃∼60℃ 범위에서 사용하는 강 구조물용 토크-전단형고장력 볼트, 6각 너트, 평와셔의 세트(이하 세트라 한다.)에 대하여 규정한다
Sets of torque-shear type high tension bolt, hexagon nut and plain washer for structural joints
KS B 2819-2005 结构缝剪断型高张力螺栓.六角螺母·平垫圈扭矩
? ??? ?? ? ???? ???? ?? 0?60
Sets of torque-shear type high tension bolt, hexagon nut and plain washer for structural joints
KS B 2819-2016 结构连接用扭剪式高强度螺栓、六角螺母、平垫圈组套
Sets of torque-shear type high tension bolt, hexagon nut and plain washer for structural joints
GB/T 32076.9-2017 预载荷高强度栓接结构连接副 第9部分：扭剪型大六角头螺栓和螺母连接副
High-strength structural bolting assemblies for preloading—Part 9: Torshear type bolt with hexagon head with large width across flats，and nut assemblies
AIA/NAS NAS 1973-1986 (Rev. 5)108ksi 剪力高扭矩及扭矩调整100度头平螺栓
NAS1972THRUNAS1980, IfBolt, Flat, 100 Deg. Head, Torq-Set and Hi-Torque, 108 K S I Shear", was adopted on 13-SEP-95 for use by the Department
Bolt, Flat, 100 Degrees Head, Torq-Set and Hi-Torque, 108 ksi Shear (Rev. 5)
AIA/NAS NAS 1974-1986 (Rev. 5)108ksi 剪力高扭矩及扭矩调整100度头平螺栓
NAS1972THRUNAS1980, IfBolt, Flat,1 00 Deg. Head, Torq-Set and Hi-Torque, 108 KSI Shear", was adopted on 13-SEP-95 for use by the Department
Bolt, Flat, 100 Degrees Head, Torq-Set and Hi-Torque, 108 ksi Shear (Rev. 5)
AIA/NAS NAS 1975-1986 (Rev. 5)108ksi 剪力高扭矩及扭矩调整100度头平螺栓
NAS1972THRUNAS1980, IfBolt, Flat, 100 Deg. Head, Torq-Set and Hi-Torque, 108 K S I Shear", was adopted on 13-SEP-95 for use by the Department
Bolt, Flat, 100 Degrees Head, Torq-Set and Hi-Torque, 108 ksi Shear (Rev. 5)
AIA/NAS NAS 1976-1986 (Rev. 5)108ksi 剪力高扭矩及扭矩调整100度头平螺栓
NAS1972THRUNAS1980, IfBolt, Flat, 100 Deg. Head, Torq-Set and Hi-Torque, 108 K S I Shear", was adopted on 13-SEP-95 for use by the Department
Bolt, Flat, 100 Degrees Head, Torq-Set and Hi-Torque, 108 ksi Shear (Rev. 5)
AIA/NAS NAS 1977-1986 (Rev. 5)108ksi 剪力高扭矩及扭矩调整100度头平螺栓
NAS1972THRUNAS1980, IfBolt, Flat, 100 Deg. Head, Torq-Set and Hi-Torque, 108 K S I Shear", was adopted on 13-SEP-95 for use by the Department
Bolt, Flat, 100 Degrees Head, Torq-Set and Hi-Torque, 108 ksi Shear (Rev. 5)
AIA/NAS NAS 1978-1986 (Rev. 5)108ksi 剪力高扭矩及扭矩调整100度头平螺栓
NAS1972THRUNAS1980, IfBolt, Flat, 100 Deg. Head, Torq-Set and Hi-Torque, 108 K S I Shear", was adopted on 13-SEP-95 for use by the Department
Bolt, Flat, 100 Degrees Head, Torq-Set and Hi-Torque, 108 ksi Shear (Rev. 5)
编辑：北检院编辑部
