GM 9984146-1993 内饰部件塑料的涂漆
Despite spot checks possibly performed by Opel, it is the supplier's responsibility that the delivered parts are in line with the Opel drawings
Lacquer, over Plastic, Interior Revision B
SANS 630:2004 高光装饰漆涂料
This standard specifies the requirements for two grades of air-drying gloss enamel paints for use on suitably primed and uncoated steel, wood, masonry
Decorative high gloss enamel paints
T/CNCIA 01008-2018 汽车塑料内饰件涂料
本标准规定了汽车内饰件涂料产品（包括溶剂型和水性涂料）的术语和定义、分类、要求、试验方法、检验规则以及标志、包装和贮存。 本标准适用于溶剂型和水性加热固化
Automobile plastic interior parts paint
GM 9984899-1998 底漆/塑料车轮装饰罩光面漆系统,
In addition the materials and components shall meet the requirements according to the relevant legislations and regulations of the countries
Topcoat System, Basecoat/Clearcoat for Plastic Wheel Trim
FORD WSS-M15J17-A1-2013 油漆，用于塑料、内饰、高光泽的单组分彩色底漆/双组分清漆 *与福特 WSS-M99P1111-A 一起使用*
PAINT, ONE COMPONENT COLOR BASECOAT/TWO COMPONENT CLEARCOAT FOR PLASTIC, INTERIOR, HIGH GLOSS *TO BE USED WITH FORD WSS-M99P1111-A*
FORD WSK-M15J4-A-2012 油漆，两件装，塑料基材，内饰 *用于福特 WSS-M99P1111-A*
PAINT, TWO PACK, PLASTIC SUBSTRATES, INTERIOR *TO BE USED WITH FORD WSS-M99P1111-A*
GSA L-P-519 C-1977 塑料板:高光和光饰面寻迹
This specification covers plastic materialin sheet orr ollform with a glazed or matte finish of such a quality to make it acceptable for use intracing
PLASTIC SHEET: TRACING, GLAZED AND MATTE FINISH
GM 9984262-1993 烯烃塑料,内饰部件,非导电底漆(粘合剂催化剂)
Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion
Primer (Adhesion Promoter) - Nonconductive, Interiors, for Olefinic Plastics
FORD ASL PAINTS-15J-2020 批准来源清单（ASL）-类别油漆和涂层材料-塑料漆-内饰
APPROVED SOURCE LIST (ASL) - CATEGORY PAINTS AND COATING MATERIALS - PAINT ON PLASTIC - INTERIOR
GME 00211-2008 汽车内饰件塑料表面喷漆的一般要求（英语/德语）
GM 9984870-1991 塑料内部高烧制珐琅面漆
In diesen Technischen Lieferbedingungen sind die qualitatsabhangigen Anforderungen dieses Polsterstoffes festgelegt. Die allgemeinen
High Bake Enamel Topcoat, over Plastic, Interior
GM GMN10044-2004 带漆膜的外饰塑料件性能要求
Performance Requirements for Exterior Plastic Parts With Paint Film
FORD ESB-M8P4-A-1978 车内用塑料饰条
PLASTIC TRIM, INTERIOR
FORD WSB-M2G368-A-2015 底漆，粘合剂，塑料装饰表面，内饰 *与福特 WSS-M99P1111-A 一起使用*
PRIMER, ADHESION, PLASTIC TRIM SURFACES, INTERIOR *TO BE USED WITH FORD WSS-M99P1111-A*
FORD ESB-M2P77-A-1978 油漆性能，装饰品的透明塑料饰面
PAINT PERFORMANCE, CLEAR PLASTIC FINISH FOR ORNAMENTS
GM 9984146-1993 内饰部件塑料的涂漆
Despite spot checks possibly performed by Opel, it is the supplier's responsibility that the delivered parts are in line with the Opel drawings
Lacquer, over Plastic, Interior Revision B
SANS 630:2004 高光装饰漆涂料
This standard specifies the requirements for two grades of air-drying gloss enamel paints for use on suitably primed and uncoated steel, wood, masonry
Decorative high gloss enamel paints
T/CNCIA 01008-2018 汽车塑料内饰件涂料
本标准规定了汽车内饰件涂料产品（包括溶剂型和水性涂料）的术语和定义、分类、要求、试验方法、检验规则以及标志、包装和贮存。 本标准适用于溶剂型和水性加热固化
Automobile plastic interior parts paint
GM 9984899-1998 底漆/塑料车轮装饰罩光面漆系统,
In addition the materials and components shall meet the requirements according to the relevant legislations and regulations of the countries
Topcoat System, Basecoat/Clearcoat for Plastic Wheel Trim
FORD WSS-M15J17-A1-2013 油漆，用于塑料、内饰、高光泽的单组分彩色底漆/双组分清漆 *与福特 WSS-M99P1111-A 一起使用*
PAINT, ONE COMPONENT COLOR BASECOAT/TWO COMPONENT CLEARCOAT FOR PLASTIC, INTERIOR, HIGH GLOSS *TO BE USED WITH FORD WSS-M99P1111-A*
FORD WSK-M15J4-A-2012 油漆，两件装，塑料基材，内饰 *用于福特 WSS-M99P1111-A*
PAINT, TWO PACK, PLASTIC SUBSTRATES, INTERIOR *TO BE USED WITH FORD WSS-M99P1111-A*
GSA L-P-519 C-1977 塑料板:高光和光饰面寻迹
This specification covers plastic materialin sheet orr ollform with a glazed or matte finish of such a quality to make it acceptable for use intracing
PLASTIC SHEET: TRACING, GLAZED AND MATTE FINISH
GM 9984262-1993 烯烃塑料,内饰部件,非导电底漆(粘合剂催化剂)
Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion
Primer (Adhesion Promoter) - Nonconductive, Interiors, for Olefinic Plastics
FORD ASL PAINTS-15J-2020 批准来源清单（ASL）-类别油漆和涂层材料-塑料漆-内饰
APPROVED SOURCE LIST (ASL) - CATEGORY PAINTS AND COATING MATERIALS - PAINT ON PLASTIC - INTERIOR
GME 00211-2008 汽车内饰件塑料表面喷漆的一般要求（英语/德语）
GM 9984870-1991 塑料内部高烧制珐琅面漆
In diesen Technischen Lieferbedingungen sind die qualitatsabhangigen Anforderungen dieses Polsterstoffes festgelegt. Die allgemeinen
High Bake Enamel Topcoat, over Plastic, Interior
GM GMN10044-2004 带漆膜的外饰塑料件性能要求
Performance Requirements for Exterior Plastic Parts With Paint Film
FORD ESB-M8P4-A-1978 车内用塑料饰条
PLASTIC TRIM, INTERIOR
FORD WSB-M2G368-A-2015 底漆，粘合剂，塑料装饰表面，内饰 *与福特 WSS-M99P1111-A 一起使用*
PRIMER, ADHESION, PLASTIC TRIM SURFACES, INTERIOR *TO BE USED WITH FORD WSS-M99P1111-A*
FORD ESB-M2P77-A-1978 油漆性能，装饰品的透明塑料饰面
PAINT PERFORMANCE, CLEAR PLASTIC FINISH FOR ORNAMENTS
编辑：北检院编辑部
