塑料模块检测

QB/T 5304-2018 雨水蓄水池用塑料模块

Plastic modules for rainwater cisterns

GB/T 40224-2021 雨水渗透、调蓄、储存用塑料模块

本文件规定了雨水渗透、调蓄、储存用塑料模块的术语和定义、分类和标记、材料、要求、试验方法、检验规则、标志、运输和贮存。 本文件适用于城镇建筑与小区、工业区及市政工程雨水控制与回收利用工程中使用的塑料模块

Plastic boxes used for rainwater infiltration,attenuation and storage

DS/EN 14598-1:2005 增强热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第1部分：名称

1.1 This part of prEN 14598 establishes a data block system for the designation of Sheet Moulding Compounds (SMC) and Bulk Moulding Compounds (BMC)1.2

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation

LST EN 14598-1-2005 增强热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第1部分：名称

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation

UNE-EN 14598-1:2006 增强热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第1部分：名称

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation

DIN EN 14598-1:2005-07 增强热固性模塑料 片状模塑料(SMC)和块状模塑料(BMC)规范 第1部分：名称

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation; German version EN 14598-1:2005

KS B 4164-2000 塑料铸模垫块

이 규격은 플라스틱용 금형에 사용하는 스페이서 블록에 대하여 규정한다

Spacer blocks of moulds for plastics

KS B 4164-2010 塑料铸模垫块

spacerblocks of moulds for plastics

DIN EN 14598-3:2005-07 增强热固性模塑料 片状模塑料(SMC)和块状模塑料(BMC)规范 第3部分：具体要求

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements; German version EN 14598-3:2005

DS/EN 14598-3:2005 增强型热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第3部分：具体要求

This part of prEN 14598 specifies the requirements for physical and chemical properties of Sheet moulding Compounds (SMC) and Bulk Moulding Compound

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements

LST EN 14598-3-2005 增强型热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第3部分：具体要求

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements

UNE-EN 14598-3:2006 增强型热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第3部分：具体要求

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements

DS/EN 14598-2/AC:2006 增强热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第2部分：测试方法和一般要求

This part of prEN 14598 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of Sheet

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements

DS/EN 14598-2:2005 增强热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第2部分：测试方法和一般要求

This part of prEN 14598 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of Sheet

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements

LST EN 14598-2-2005 增强热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第2部分：测试方法和一般要求

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements

QB/T 5304-2018 雨水蓄水池用塑料模块

Plastic modules for rainwater cisterns

GB/T 40224-2021 雨水渗透、调蓄、储存用塑料模块

本文件规定了雨水渗透、调蓄、储存用塑料模块的术语和定义、分类和标记、材料、要求、试验方法、检验规则、标志、运输和贮存。 本文件适用于城镇建筑与小区、工业区及市政工程雨水控制与回收利用工程中使用的塑料模块

Plastic boxes used for rainwater infiltration,attenuation and storage

DS/EN 14598-1:2005 增强热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第1部分：名称

1.1 This part of prEN 14598 establishes a data block system for the designation of Sheet Moulding Compounds (SMC) and Bulk Moulding Compounds (BMC)1.2

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation

LST EN 14598-1-2005 增强热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第1部分：名称

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation

UNE-EN 14598-1:2006 增强热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第1部分：名称

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation

DIN EN 14598-1:2005-07 增强热固性模塑料 片状模塑料(SMC)和块状模塑料(BMC)规范 第1部分：名称

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation; German version EN 14598-1:2005

KS B 4164-2000 塑料铸模垫块

이 규격은 플라스틱용 금형에 사용하는 스페이서 블록에 대하여 규정한다

Spacer blocks of moulds for plastics

KS B 4164-2010 塑料铸模垫块

spacerblocks of moulds for plastics

DIN EN 14598-3:2005-07 增强热固性模塑料 片状模塑料(SMC)和块状模塑料(BMC)规范 第3部分：具体要求

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements; German version EN 14598-3:2005

DS/EN 14598-3:2005 增强型热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第3部分：具体要求

This part of prEN 14598 specifies the requirements for physical and chemical properties of Sheet moulding Compounds (SMC) and Bulk Moulding Compound

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements

LST EN 14598-3-2005 增强型热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第3部分：具体要求

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements

UNE-EN 14598-3:2006 增强型热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第3部分：具体要求

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements

DS/EN 14598-2/AC:2006 增强热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第2部分：测试方法和一般要求

This part of prEN 14598 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of Sheet

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements

DS/EN 14598-2:2005 增强热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第2部分：测试方法和一般要求

This part of prEN 14598 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of Sheet

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements

LST EN 14598-2-2005 增强热固性模塑料 片状模塑料（SMC）和块状模塑料（BMC）规范 第2部分：测试方法和一般要求

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements