汽车塑料燃油管检测

QC/T 798-2008 汽车用多层塑料燃油管

本标准规定了汽车用多层塑料燃油管及管总成的尺寸规格、外观、技术要求、试验方法、检验规则和标志、包装、运输和储存。、本标准适用于工作温度在-40℃到+115℃之间(连续使用温度不应超过90℃)，最大工作压力不超过0.7MPa的多层塑料燃油管

Multi-layers plastic tubing for automotive fuel system

BS ISO 13775-2:2000 汽车用热塑管和软管.石油类燃料用

This part of ISO 13775 specifies test requirements and test methods for extruded thermoplastic tubing and hoses for use in petroleum-based-fuel lines

Thermoplastic tubing and hoses for automotive use - Petroleum-based fuel applications

BS ISO 13775-2:2016 汽车用热塑管和软管.石油类燃料用

Thermoplastic tubing and hoses for automotive use. Petroleum-based-fuel applications

DB34/T 1664-2012 汽车塑料燃油箱

本标准规定了汽车塑料燃油箱（以下简称燃油箱）的术语和定义、要求、试验方法、检验规则、标识、包装、运输和贮存。 本标准适用于汽车用吹塑型塑料箱体，经焊接、组装零配件而成的汽车塑料燃油箱总成

Automotive Plastic Fuel Tank

QC/T 1121-2019 汽车用塑料燃油箱

Plastic fuel tank for automobiles

JASO M316-1980 汽车燃油软管

Fuel hoses for automobiles

BS ISO 13775-1:2000 汽车用热塑管和软管.非燃料应用

This part of ISO 13775 specifies the test requirements and the test methods for extruded thermoplastic tubing and hoses for use in vehicles powered

Thermoplastic tubing and hoses for automotive use - Non-fuel applications

BS ISO 13775-1:2015 汽车用热塑管和软管.非燃料应用

Thermoplastic tubing and hoses for automotive use. Non-fuel applications

KS R 3044-2008 汽车柴油机高压燃料喷射管

이 표준은 자동차용 디젤 엔진에 사용하는 고압 연료 분사관 소재 강관(이하 강관이라 한다

Automotive diesel engines-Steel tubes for high-pressure fuel injection pipes

AS 3570:1998 汽车柴油机燃料

Sets out requirements for automotive diesel fuel (intended for use in high speed diesel engines) which would minimize engine problems, particularly

Automotive diesel fuel

GOST R 51866-2002 汽车燃料.铅汽油.规范

Automotive fuels. Unleaded petrol. Specifications

BS ISO 13775-1:2021 汽车用热塑性管材和软管 非燃料应用

Thermoplastic tubing and hoses for automotive use. Non-fuel applications

SANS 342:2006 汽车用柴油机燃料

specifies two grades of automotive diesel fuel (low sulphur grade and standard grade) suitable for use in compression-ignition engines, including

Automotive diesel fuel

JJF(汽车) 02-2008 汽车速度计校准规范

Automobile Speedometer Calibration Specification

GB/T 20462.2-2006 汽车用热塑性非增强软管和软管.第2部分;石油基燃油用

GB/T 20462的本部分规定了公称内经2mm～14mm的六种型别的内燃机驱动的车辆石油基燃油管线用挤出热塑性非增强软管的结构、类型、尺寸、试验要求和试验方法

Thermoplastic tubing and hoses for automotive use.Part 2:Petroleum-based-fuel applications

QC/T 798-2008 汽车用多层塑料燃油管

本标准规定了汽车用多层塑料燃油管及管总成的尺寸规格、外观、技术要求、试验方法、检验规则和标志、包装、运输和储存。、本标准适用于工作温度在-40℃到+115℃之间(连续使用温度不应超过90℃)，最大工作压力不超过0.7MPa的多层塑料燃油管

Multi-layers plastic tubing for automotive fuel system

BS ISO 13775-2:2000 汽车用热塑管和软管.石油类燃料用

This part of ISO 13775 specifies test requirements and test methods for extruded thermoplastic tubing and hoses for use in petroleum-based-fuel lines

Thermoplastic tubing and hoses for automotive use - Petroleum-based fuel applications

BS ISO 13775-2:2016 汽车用热塑管和软管.石油类燃料用

Thermoplastic tubing and hoses for automotive use. Petroleum-based-fuel applications

DB34/T 1664-2012 汽车塑料燃油箱

本标准规定了汽车塑料燃油箱（以下简称燃油箱）的术语和定义、要求、试验方法、检验规则、标识、包装、运输和贮存。 本标准适用于汽车用吹塑型塑料箱体，经焊接、组装零配件而成的汽车塑料燃油箱总成

Automotive Plastic Fuel Tank

QC/T 1121-2019 汽车用塑料燃油箱

Plastic fuel tank for automobiles

JASO M316-1980 汽车燃油软管

Fuel hoses for automobiles

BS ISO 13775-1:2000 汽车用热塑管和软管.非燃料应用

This part of ISO 13775 specifies the test requirements and the test methods for extruded thermoplastic tubing and hoses for use in vehicles powered

Thermoplastic tubing and hoses for automotive use - Non-fuel applications

BS ISO 13775-1:2015 汽车用热塑管和软管.非燃料应用

Thermoplastic tubing and hoses for automotive use. Non-fuel applications

KS R 3044-2008 汽车柴油机高压燃料喷射管

이 표준은 자동차용 디젤 엔진에 사용하는 고압 연료 분사관 소재 강관(이하 강관이라 한다

Automotive diesel engines-Steel tubes for high-pressure fuel injection pipes

AS 3570:1998 汽车柴油机燃料

Sets out requirements for automotive diesel fuel (intended for use in high speed diesel engines) which would minimize engine problems, particularly

Automotive diesel fuel

GOST R 51866-2002 汽车燃料.铅汽油.规范

Automotive fuels. Unleaded petrol. Specifications

BS ISO 13775-1:2021 汽车用热塑性管材和软管 非燃料应用

Thermoplastic tubing and hoses for automotive use. Non-fuel applications

SANS 342:2006 汽车用柴油机燃料

specifies two grades of automotive diesel fuel (low sulphur grade and standard grade) suitable for use in compression-ignition engines, including

Automotive diesel fuel

JJF(汽车) 02-2008 汽车速度计校准规范

Automobile Speedometer Calibration Specification

GB/T 20462.2-2006 汽车用热塑性非增强软管和软管.第2部分;石油基燃油用

GB/T 20462的本部分规定了公称内经2mm～14mm的六种型别的内燃机驱动的车辆石油基燃油管线用挤出热塑性非增强软管的结构、类型、尺寸、试验要求和试验方法

Thermoplastic tubing and hoses for automotive use.Part 2:Petroleum-based-fuel applications