电子设备用机电开关 微动开关检测

GB/T 13419-1998 电子设备用机电开关 第6部分;微动开关分规范

本分规范适用于质量评定的机电开关类微动开关分门类。它包括额定电压不大于300V和额定电流不大于25A（直流或交流有效值）的微动开关

Electromechanical switches for use in electronic equipment. Part 6: Sectional specification for sensitive switches

KS C IEC 61020-6-2002(2017 电子设备第6部分用机电开关:微动开关分规范

Electromechanical switches for use in electronic equipment－Part 6：Sectional specification for sensitive switches

IEC 61020-6:1991 电子设备用机电开关 第6部分:微动开关的分规范

Prescribes preferred ratings and characteristics, general performance requirements, and selects the appropriate quality assessment procedures and test

Electromechanical switches for use in electronic equipment; part 6: sectional specification for sensitive switches

GB/T 13420-1998 电子设备用机电开关 第6部分:微动开关分规范 第1篇:空白详细规范

空白详细规范是分规范的一种补充性文件，包括详细规范的格式、编排和最少内容的要求。 不符合这些要求的详细规范，不能作为符合IECQ体系要求的标准

Electromechanical switches for use in electronic equipment. Part 6: Sectional specification for sensitive switches. Section 1: Blank detail specification

KS C IEC 61020-6:2002 电子设备用的机电开关.第6部分:微动开关的分规范

이 규격은 전자 기계식 스위치의 정격 전압 300 V 이하, 정격 전류 25 A(d.c

Electromechanical switches for use in electronic equipment－Part 6：Sectional specification for sensitive switches

IEC 61020-6-1:1991 电子设备用机电开关 第6部分:微动开关的分规范 第1节:空白详细规范

Contains requirements for style, lay-out and minimum content of detail specifications

Electromechanical switches for use in electronic equipment; part 6: sectional specification for sensitive switches; section 1: blank detail specification

DIN IEC 61020-6-1:1994 电子设备用的机电开关.第6部分:微动开关的分规范.第1节:空白详细规范

The document is an blank detail specification based on IEC 1020-6

Electromechanical switches for use in electronic equipment; part 6: sectional specification for sensitive switches; section 1: blank detail specification; identical with IEC 61020-6-1:1991

KS C IEC 61020-6-1:2002 电子设备用的机电开关.第6部分:微动开关的分规范.第1节:空白详细规范

서 문 이 규격은 1991년에 발행된 IEC 61020-6-1 Electromecha

Electromechanical switches for use in electronic equipment-Part 6:Sectional specification for sensitive switches-Section 1:Blank detail specification

KS C IEC 61020-6-1:2014 电子设备用的机电开关 第6部分：微动开关的分规范 第1节 空白详细规范

Electromechanical switches for use in electronic equipment－Part 6：Sectional specification for sensitive switches－Section 1：Blank detail specification

IEC 61020-6-2:1994 电子设备用机电开关 第6部分:微动开关的分规范 第2节:电气定额最高电压250V、最大电流5A的单级不密封超小型微动开关的详细规范

Describes complete requirements for the switches corresponding to this detail specification, and the current issues of IEC 1020-1 and IEC 1020-6

Electromechanical switches for use in electronic equipment - Part 6: Sectional specification for sensitive switches - Section 2: Detail specification for one pole, unsealed subminiature sensitive switches, 250 V maximum, 5 A maximum electrical rating

DIN IEC 61020-6:1994 电子设备的机电开关.第6部分:微动开关分规范

The document applies to the sub-family of sensitive switches within the family of electromechanical switches of assessed quality. Sensitive switches

Electromechanical switches for use in electronic equipment; part 6: sectional specification for sensitive switches; identical with IEC 61020-6:1991

SJ/T 10493-1994 电子设备用机电开关详细规范.KND2型波动开关

本规范适用于KND2型波动开关，它是按照IEC 1020-4-1/QC 960201《电子设备用机电开关 第4-1部分：钮子开关空白详细规范》制订的，符合IEC 1020-1/QC 960000《电子设备用机电开关 第1部分：总规范》和IEC 1020-4/QC 960200《电子设备用机电开关

Detail specification for elecromechanical switches for use in electronic equipment waviness switches type KND2

SJ/T 10492-1994 电子设备用机电开关详细规范.KND1型波动开关

本规范适用于KND1型波动开关，它是按照IEC 1020-4-1/QC 960201《电子设备用机电开关 第4-1部分：钮子开关空白详细规范》制订的，符合IEC 1020-1/QC 960000《电子设备用机电开关 第1部分：总规范》和IEC 1020-4/QC 960200《电子设备用机电开关

Detail specification for elecromechanical switches for use in electronic equipment waviness switches type KND1

SJ/T 10489-1994 电子设备用机电开关详细规范.KN3型钮子开关

本规范适用于KN3型钮子开关，它是按照IEC1020-4-1/QC960201《电子设备用机电开关 第4-1部分：钮子开关空白详细规范》制订的。符合IEC1020-1/QC960000《电子设备用机电开关 第1部分：总规范》和IEC1020-4/QC960200《电子设备用机电开关 第4部分

Detail specification for electromechanical switches for use in electronic equipment lever(toggle)switches type KN3

SJ/T 10491-1994 电子设备用机电开关详细规范.KN6型钮子开关

本规范适用于KN6型钮子开关，它是按照IEC 1020-4-1/QC 960201《电子设备用机电开关 第4-1部分：钮子开关空白详细规范》制订的，符合IEC 1020-1/QC 960000《电子设备用机电开关 第1部分：总规范)和IEC 1020-4/QC 960200《电子设备用机电开关

Detail specification for electromechanical switches for use in electronic equipment lever(toggle)switches type KN6

GB/T 13419-1998 电子设备用机电开关 第6部分;微动开关分规范

本分规范适用于质量评定的机电开关类微动开关分门类。它包括额定电压不大于300V和额定电流不大于25A（直流或交流有效值）的微动开关

Electromechanical switches for use in electronic equipment. Part 6: Sectional specification for sensitive switches

KS C IEC 61020-6-2002(2017 电子设备第6部分用机电开关:微动开关分规范

Electromechanical switches for use in electronic equipment－Part 6：Sectional specification for sensitive switches

IEC 61020-6:1991 电子设备用机电开关 第6部分:微动开关的分规范

Prescribes preferred ratings and characteristics, general performance requirements, and selects the appropriate quality assessment procedures and test

Electromechanical switches for use in electronic equipment; part 6: sectional specification for sensitive switches

GB/T 13420-1998 电子设备用机电开关 第6部分:微动开关分规范 第1篇:空白详细规范

空白详细规范是分规范的一种补充性文件，包括详细规范的格式、编排和最少内容的要求。 不符合这些要求的详细规范，不能作为符合IECQ体系要求的标准

Electromechanical switches for use in electronic equipment. Part 6: Sectional specification for sensitive switches. Section 1: Blank detail specification

KS C IEC 61020-6:2002 电子设备用的机电开关.第6部分:微动开关的分规范

이 규격은 전자 기계식 스위치의 정격 전압 300 V 이하, 정격 전류 25 A(d.c

Electromechanical switches for use in electronic equipment－Part 6：Sectional specification for sensitive switches

IEC 61020-6-1:1991 电子设备用机电开关 第6部分:微动开关的分规范 第1节:空白详细规范

Contains requirements for style, lay-out and minimum content of detail specifications

Electromechanical switches for use in electronic equipment; part 6: sectional specification for sensitive switches; section 1: blank detail specification

DIN IEC 61020-6-1:1994 电子设备用的机电开关.第6部分:微动开关的分规范.第1节:空白详细规范

The document is an blank detail specification based on IEC 1020-6

Electromechanical switches for use in electronic equipment; part 6: sectional specification for sensitive switches; section 1: blank detail specification; identical with IEC 61020-6-1:1991

KS C IEC 61020-6-1:2002 电子设备用的机电开关.第6部分:微动开关的分规范.第1节:空白详细规范

서 문 이 규격은 1991년에 발행된 IEC 61020-6-1 Electromecha

Electromechanical switches for use in electronic equipment-Part 6:Sectional specification for sensitive switches-Section 1:Blank detail specification

KS C IEC 61020-6-1:2014 电子设备用的机电开关 第6部分：微动开关的分规范 第1节 空白详细规范

Electromechanical switches for use in electronic equipment－Part 6：Sectional specification for sensitive switches－Section 1：Blank detail specification

IEC 61020-6-2:1994 电子设备用机电开关 第6部分:微动开关的分规范 第2节:电气定额最高电压250V、最大电流5A的单级不密封超小型微动开关的详细规范

Describes complete requirements for the switches corresponding to this detail specification, and the current issues of IEC 1020-1 and IEC 1020-6

Electromechanical switches for use in electronic equipment - Part 6: Sectional specification for sensitive switches - Section 2: Detail specification for one pole, unsealed subminiature sensitive switches, 250 V maximum, 5 A maximum electrical rating

DIN IEC 61020-6:1994 电子设备的机电开关.第6部分:微动开关分规范

The document applies to the sub-family of sensitive switches within the family of electromechanical switches of assessed quality. Sensitive switches

Electromechanical switches for use in electronic equipment; part 6: sectional specification for sensitive switches; identical with IEC 61020-6:1991

SJ/T 10493-1994 电子设备用机电开关详细规范.KND2型波动开关

本规范适用于KND2型波动开关，它是按照IEC 1020-4-1/QC 960201《电子设备用机电开关 第4-1部分：钮子开关空白详细规范》制订的，符合IEC 1020-1/QC 960000《电子设备用机电开关 第1部分：总规范》和IEC 1020-4/QC 960200《电子设备用机电开关

Detail specification for elecromechanical switches for use in electronic equipment waviness switches type KND2

SJ/T 10492-1994 电子设备用机电开关详细规范.KND1型波动开关

本规范适用于KND1型波动开关，它是按照IEC 1020-4-1/QC 960201《电子设备用机电开关 第4-1部分：钮子开关空白详细规范》制订的，符合IEC 1020-1/QC 960000《电子设备用机电开关 第1部分：总规范》和IEC 1020-4/QC 960200《电子设备用机电开关

Detail specification for elecromechanical switches for use in electronic equipment waviness switches type KND1

SJ/T 10489-1994 电子设备用机电开关详细规范.KN3型钮子开关

本规范适用于KN3型钮子开关，它是按照IEC1020-4-1/QC960201《电子设备用机电开关 第4-1部分：钮子开关空白详细规范》制订的。符合IEC1020-1/QC960000《电子设备用机电开关 第1部分：总规范》和IEC1020-4/QC960200《电子设备用机电开关 第4部分

Detail specification for electromechanical switches for use in electronic equipment lever(toggle)switches type KN3

SJ/T 10491-1994 电子设备用机电开关详细规范.KN6型钮子开关

本规范适用于KN6型钮子开关，它是按照IEC 1020-4-1/QC 960201《电子设备用机电开关 第4-1部分：钮子开关空白详细规范》制订的，符合IEC 1020-1/QC 960000《电子设备用机电开关 第1部分：总规范)和IEC 1020-4/QC 960200《电子设备用机电开关

Detail specification for electromechanical switches for use in electronic equipment lever(toggle)switches type KN6