KS B 1533-2016 螺纹式钢制管件
Screwed type steel pipe fittings
T/CCCTA 0040-2023 3PE耐蚀钢制管件
本文件规定了3PE耐蚀钢制管件（以下简称“耐蚀管件”）的耐蚀层结构、规格、技术要求、制造、试验方法、检验规则、标志、搬运和贮存等要求
3PE anticorrosion steel fittings
DIN 2615-1:1992 对焊钢制管件.带有换算压力系数的丁字管接
The document applies to seamless and welded tees having the same wall thicknesses than the steel tubes to be welded on. This tees are used as welding
Steel butt-welding pipes fittings; tees with reduced pressure factor
DIN 2615-2:1992 对焊钢制管件.在全工作压力下使用的丁字管接
The document applies to seamless and welded tees having reinforced wall thickness than the steel tubes to be welded on. This tees are used as welding
Steel butt-welding pipe fittings; tees for use at full service pressure
GB/T 17185-2012 钢制法兰管件
本标准规定了用Class标记的钢制法兰管件的种类及代号、尺寸与公差、技术要求、水压试验、检验标志及包装、本标准适用于公称压力为Class150和Class300的钢制法兰管件
Steel flanged fittings
CNS 2929-1972 螺纹式钢管制管件（配合有缝钢管用）（压力在１６ｋｇ／ｃ㎡以下）
本标准适用于蒸汽、水、气体及液体管系，其使用压力在 16 kg∕cm2 以下之一般配管用之螺纹式钢管件。本标准不适用于高压管系及电线管系之管件
Screwed Type Steel Pipe Fitting
GB/T 17185-1997 钢制法兰管件
本标准规定了公称压力PN为2.0、5.0、11.0、15.0及26.0MPa的碳钢、合金钢和奥氏体不锈钢制 标准型法兰管件（包括弯头、三通、四通、斜三通及异径接头）的尺寸、公差、技术要求、检验和标志
Steel pipe fittings for flanged joint
SY/T 0510-1998 钢制对焊管件
本标准规定了碳钢、低合金钢及不锈钢制造的对焊管件的尺寸、技术要求、试验方法和标记等，其中包括公称直径15-600mm (1/2-24in)的弯头、异径接头、三通、四通和管帽。 本标准适用于石油、化工、电力、船舶、轻工等工业管道所使用的钢制对焊管件。用户如有特殊要求，经供需双方协商，管件可按
Steel but - welding pipe fitting
CEN EN 10241-2000 钢制螺纹管件
Steel Threaded Pipe Fittings
DS/EN 10241:2001 钢制螺纹管件
This European standard specifies requirements for threaded fittings of nominal sizes from DN 6 to DN 150 inclusive, made out of welded or seamless
Steel threaded pipe fittings
LST EN 10241-2001 钢制螺纹管件
Steel threaded pipe fittings
UNE-EN 10241:2001 钢制螺纹管件
Steel threaded pipe fittings.
KS B 1543-2017 钢制对焊管件
Steel butt-welding pipe fittings
KS B 1543-2017(2022 钢制对焊管件
Steel butt-welding pipe fittings
KS B 1543-1986 钢制对焊管件
Steel butt-welding pipe fittings
KS B 1533-2016 螺纹式钢制管件
Screwed type steel pipe fittings
T/CCCTA 0040-2023 3PE耐蚀钢制管件
本文件规定了3PE耐蚀钢制管件（以下简称“耐蚀管件”）的耐蚀层结构、规格、技术要求、制造、试验方法、检验规则、标志、搬运和贮存等要求
3PE anticorrosion steel fittings
DIN 2615-1:1992 对焊钢制管件.带有换算压力系数的丁字管接
The document applies to seamless and welded tees having the same wall thicknesses than the steel tubes to be welded on. This tees are used as welding
Steel butt-welding pipes fittings; tees with reduced pressure factor
DIN 2615-2:1992 对焊钢制管件.在全工作压力下使用的丁字管接
The document applies to seamless and welded tees having reinforced wall thickness than the steel tubes to be welded on. This tees are used as welding
Steel butt-welding pipe fittings; tees for use at full service pressure
GB/T 17185-2012 钢制法兰管件
本标准规定了用Class标记的钢制法兰管件的种类及代号、尺寸与公差、技术要求、水压试验、检验标志及包装、本标准适用于公称压力为Class150和Class300的钢制法兰管件
Steel flanged fittings
CNS 2929-1972 螺纹式钢管制管件（配合有缝钢管用）（压力在１６ｋｇ／ｃ㎡以下）
本标准适用于蒸汽、水、气体及液体管系，其使用压力在 16 kg∕cm2 以下之一般配管用之螺纹式钢管件。本标准不适用于高压管系及电线管系之管件
Screwed Type Steel Pipe Fitting
GB/T 17185-1997 钢制法兰管件
本标准规定了公称压力PN为2.0、5.0、11.0、15.0及26.0MPa的碳钢、合金钢和奥氏体不锈钢制 标准型法兰管件（包括弯头、三通、四通、斜三通及异径接头）的尺寸、公差、技术要求、检验和标志
Steel pipe fittings for flanged joint
SY/T 0510-1998 钢制对焊管件
本标准规定了碳钢、低合金钢及不锈钢制造的对焊管件的尺寸、技术要求、试验方法和标记等，其中包括公称直径15-600mm (1/2-24in)的弯头、异径接头、三通、四通和管帽。 本标准适用于石油、化工、电力、船舶、轻工等工业管道所使用的钢制对焊管件。用户如有特殊要求，经供需双方协商，管件可按
Steel but - welding pipe fitting
CEN EN 10241-2000 钢制螺纹管件
Steel Threaded Pipe Fittings
DS/EN 10241:2001 钢制螺纹管件
This European standard specifies requirements for threaded fittings of nominal sizes from DN 6 to DN 150 inclusive, made out of welded or seamless
Steel threaded pipe fittings
LST EN 10241-2001 钢制螺纹管件
Steel threaded pipe fittings
UNE-EN 10241:2001 钢制螺纹管件
Steel threaded pipe fittings.
KS B 1543-2017 钢制对焊管件
Steel butt-welding pipe fittings
KS B 1543-2017(2022 钢制对焊管件
Steel butt-welding pipe fittings
KS B 1543-1986 钢制对焊管件
Steel butt-welding pipe fittings
编辑：北检院编辑部
