DL/T 515-2004 电站弯管
本标准適用說电站主 FLAN i Si till tk SSS. SC A HE 管可参照使用
Pipe bends for power station
SY/T 5257-1991 钢制弯管
steel elbow
UNI 5194-1970 燃气管用可锻造铁螺纹连接管．弯管；公弯管；内弯管；丁字管；十字管；弯管输送管和丁字输送管
JB/T 2671.1-1998 弯管机.参数
本标准规定了弯管机的基本参数。 本标准适用于金属管材在冷态下弯曲的缠绕式弯管机
Pipe bender parameters
GB/T 28763-2012 数控弯管机
本标准规定了数控弯管机型式与参数、技术要求、精度、试验方法、检验规则、包装、运输与贮存。 本标准适用于金属管材在冷态下弯曲的缠绕式数控弯管机（以下简称弯管机）。 本标准不适用于顶镦型弯管机、弯管流水线或其他专用弯管机
Numerically controlled tube bending machine
HB 5569-1981 弯管接头
elbow joint
HB 5570-1983 弯管接头
elbow joint
DLA MS27234 REV C-2007 90度弯管
Dimensions are in inches. Metric equivalents are given for information only. Unless otherwise specified, break all corners, radius .010/.005 inch
ELBOW TUBE, 90 DEG.
DLA MS27235 REV D-2007 45度弯管
Face of tube must be perpendicular to centerline of the tube within X total indicator reading
ELBOW TUBE, 45 DEG.
AIR FORCE MIL-D-9898 C NOTICE 1-1996 拉拔弯管
MIL-D-9898C is inactive for new design and is no longer used, except for replacement purposes
DRAWING, TUBE BEND
AIR FORCE MIL-D-9898 C-1986 拉拔弯管
This specification is mandatory for use by all Departments and Agencies of the Department of Defense
DRAWING, TUBE BEND
DLA MS27234 REV C VALID NOTICE 1-2013 弯管，90 度
Elbow Tube, 90 Degrees
DLA MS27235 REV D VALID NOTICE 1-2013 弯管，45 度
Elbow Tube, 45 Degrees
AIR FORCE MIL-D-9898 C VALID NOTICE 2-2008 拉制弯管
Drawing, Tube Bend
DL/T 515-2018 电站弯管
Power station elbow
DL/T 515-2004 电站弯管
本标准適用說电站主 FLAN i Si till tk SSS. SC A HE 管可参照使用
Pipe bends for power station
SY/T 5257-1991 钢制弯管
steel elbow
UNI 5194-1970 燃气管用可锻造铁螺纹连接管．弯管；公弯管；内弯管；丁字管；十字管；弯管输送管和丁字输送管
JB/T 2671.1-1998 弯管机.参数
本标准规定了弯管机的基本参数。 本标准适用于金属管材在冷态下弯曲的缠绕式弯管机
Pipe bender parameters
GB/T 28763-2012 数控弯管机
本标准规定了数控弯管机型式与参数、技术要求、精度、试验方法、检验规则、包装、运输与贮存。 本标准适用于金属管材在冷态下弯曲的缠绕式数控弯管机（以下简称弯管机）。 本标准不适用于顶镦型弯管机、弯管流水线或其他专用弯管机
Numerically controlled tube bending machine
HB 5569-1981 弯管接头
elbow joint
HB 5570-1983 弯管接头
elbow joint
DLA MS27234 REV C-2007 90度弯管
Dimensions are in inches. Metric equivalents are given for information only. Unless otherwise specified, break all corners, radius .010/.005 inch
ELBOW TUBE, 90 DEG.
DLA MS27235 REV D-2007 45度弯管
Face of tube must be perpendicular to centerline of the tube within X total indicator reading
ELBOW TUBE, 45 DEG.
AIR FORCE MIL-D-9898 C NOTICE 1-1996 拉拔弯管
MIL-D-9898C is inactive for new design and is no longer used, except for replacement purposes
DRAWING, TUBE BEND
AIR FORCE MIL-D-9898 C-1986 拉拔弯管
This specification is mandatory for use by all Departments and Agencies of the Department of Defense
DRAWING, TUBE BEND
DLA MS27234 REV C VALID NOTICE 1-2013 弯管，90 度
Elbow Tube, 90 Degrees
DLA MS27235 REV D VALID NOTICE 1-2013 弯管，45 度
Elbow Tube, 45 Degrees
AIR FORCE MIL-D-9898 C VALID NOTICE 2-2008 拉制弯管
Drawing, Tube Bend
DL/T 515-2018 电站弯管
Power station elbow
编辑：北检院编辑部
